Changes for page Openwrt for Linksys EA8100
Last modified by Leon Poon on 2021/07/16 18:40
Summary
-
Page properties (2 modified, 0 added, 0 removed)
-
Attachments (0 modified, 0 added, 3 removed)
Details
- Page properties
-
- Parent
-
... ... @@ -1,1 +1,1 @@ 1 -Linksys EA8100.WebHome 1 +Main.Linksys EA8100.WebHome - Content
-
... ... @@ -1,121 +1,33 @@ 1 1 switch0: port 0 = wan, port 1,2,3,4 = lan 2 2 3 -If you brick your router you should be able to recover by soldering the UART pin headers and connecting to the serial. See [[this page for pictures>>ea8100]]. 4 4 4 +[[https:~~/~~/github.com/LeonPoon/openwrt/compare/master...master-linksys_ea8100>>https://github.com/LeonPoon/openwrt/compare/master...master-linksys_ea8100]] 5 5 6 - = 19.07.x=6 +b90086cc98a15a2774382b691f1249f4ad11a1c7 Download (no wifi): 7 7 8 -[[https:~~/~~/www.codepowered.com/openwrt/v19.07.3/linksys_ea8100/>>url:https://www.codepowered.com/openwrt/v19.07.3/linksys_ea8100/]] ([[https:~~/~~/github.com/LeonPoon/openwrt/compare/v19.07.3...v19.07.3-linksys_ea8100>>url:https://github.com/LeonPoon/openwrt/compare/v19.07.3...v19.07.3-linksys_ea8100]]) 8 +* [[initramfs-kernel.bin>>attach:Linksys EA8100.Openwrt for Linksys EA8100.WebHome@openwrt-ramips-mt7621-ea8100-initramfs-kernel.bin]] 9 +* [[squashfs-sysupgrade.bin>>attach:Linksys EA8100.Openwrt for Linksys EA8100.WebHome@openwrt-ramips-mt7621-ea8100-squashfs-sysupgrade.bin]] (accepted as upgrade in factory UI) 9 9 10 -The EA8100 contains 2 firmware partitions. Using the Linksys UI will flash openwrt into only one of the 2 partitions. The booting process switches partition every few boots, so if you want to always boot into openwrt then you have to flash openwrt into both partition. 11 - 12 -How to flash: 13 - 14 -If your router currently has stock Linksys firmware: 15 - 16 -1. flash the "squashfs-factory.img" via Linksys UI, cross your fingers that it boots openwrt when auto rebooting. Otherwise keep rebooting until it loads openwrt. (Usually 3 times max.) 17 -1. access LuCI via LAN. (It's at 192.168.1.1 so you should set connect your computer and configure your computer with an IP on same subnet eg 192.168.1.2/24). Set root password so that SSH server starts. (do not configure/restart.) 18 -1. Scp the "squashfs-sysupgrade.bin" into /tmp in the router. 19 -1. Log in via SSH. 20 -1. Sysupgrade the squashfs-sysupgrade.bin. This should flash the openwrt firmware into both firmware partitions. It auto reboots. 21 - 22 -If you are on my 18.x below, sysupgrade will not work. You have to manually mtd write the 19.07 "kernel-initramfs.bin" and boot into it, then sysupgrade. Back up data before mtd write! 23 - 24 -Subsequently sysupgrade from 19.07.x should work but it will **not **save config! Back up your config and other files in the router before you sysupgrade. 25 - 26 -Wifi seem to work at 30-40MB/s with a MacBook Pro. 27 - 28 - 29 -= 18.x = 30 - 31 -9bebafcb5dfe37f25285fa18fb8bfe7b68011267 (with wifi support) Download: 32 - 33 -* [[initramfs-kernel.bin>>attach:openwrt-ramips-mt7621-linksys_ea8100-initramfs-kernel-9bebafcb5dfe37f25285fa18fb8bfe7b68011267.bin]] 34 -* [[squashfs-sysupgrade.bin>>attach:openwrt-ramips-mt7621-linksys_ea8100-squashfs-sysupgrade-9bebafcb5dfe37f25285fa18fb8bfe7b68011267.bin]] (accepted as upgrade in factory UI) 35 - 36 -Note that sysupgrade to a newer image is not likely to work. 37 - 38 -(% border="1" cellpadding="0" cellspacing="0" style="margin-right:auto; width:auto" %) 39 -|[[image:1567332570723-651.png]] 40 - 41 41 Dmesg: 42 42 43 43 {{code language="plain"}} 44 - 3: Boot system code via Flash (default). 45 - 4: Entr boot command line interface. 46 - 7: Load Boot Loader code then write to Flash via Serial. 47 - 9: Load Boot Loader code then write to Flash via TFTP. 4 48 -You choosed 2 49 - 0 14 +check env def auto_recovery no 15 +check env def auto_recovery yes 16 +check env def boot_part 1 17 +check env def boot_part_ready 3 18 +enabled:1, boot_part:2, boot_part_ready:3 19 +..nand read ret = 0x20000 20 +boot_count:1, next_record:4 21 +boot_count:1, next_record:4 50 50 51 - 52 -2: System Load Linux Kernel then write to Flash via TFTP. 53 - Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N) 54 - Please Input new ones /or Ctrl-C to discard 55 - Input device IP () ==: 56 - Input server IP () ==: 57 - Input Linux Kernel filename (openwrt-ramips-mt7621-linksys_ea8100-initramfs-kernel.bin) ==:openwrt-ramips-mt7621-linksys_ea8100-squashfs-sysupgrade.bin 58 - which kernel partition to update (1/2/3=both) (2) ==:3 59 - 60 - NetTxPacket = 0x8FFE3200 61 - 62 - KSEG1ADDR(NetTxPacket) = 0xAFFE3200 63 - 64 - NetLoop,call eth_halt ! 65 - 66 - NetLoop,call eth_init ! 67 -Trying Eth0 (10/100-M) 68 - 69 - Waitting for RX_DMA_BUSY status Start... done 70 - 71 - 72 - ETH_STATE_ACTIVE!! 73 -TFTP from server ; our IP address is 74 -Filename 'openwrt-ramips-mt7621-linksys_ea8100-squashfs-sysupgrade.bin'. 75 - 76 - TIMEOUT_COUNT=10,Load address: 0x80100000 77 -Loading: Got ARP REPLY, set server/gtwy eth addr () 78 -Got it 79 -################################################################# 80 - ################################################################# 81 - ################################################################# 82 - ################################################################# 83 - ################################################################# 84 - ################################################################# 85 - ################################################################# 86 - ################################################################# 87 - ################################################################# 88 - ################################################################# 89 - ################################################################# 90 - ################################################################# 91 - ################################################################# 92 - ################################################################# 93 - ################################################################# 94 - ################################################################# 95 - ################################################################# 96 - ################################################ 97 -done 98 -Bytes transferred = 5898496 (5a0100 hex) 99 -LoadAddr=80100000 NetBootFileXferSize= 005a0100 100 -ranand_erase: start:180000, len:20000 101 -..ranand_erase: start:1a0000, len:20000 102 -..ranand_erase: start:1c0000, len:20000 103 -... 104 -.(5192)offs=7471104 piece=0 piece_size=256 rc=0 105 -Done! 106 -ranand_erase: start:2980000, len:20000 107 -..ranand_erase: start:29a0000, len:20000 108 -..ranand_erase: start:29c0000, len:20000 109 -... 110 -.(5192)offs=49676288 piece=0 piece_size=256 rc=0 111 -Done! 112 -## Booting image at bc180000 ... 113 - Image Name: MIPS OpenWrt Linux-4.14.141 23 +3: System Boot system code via Flash. 24 +## Booting image at be980000 ... 25 + Image Name: MIPS OpenWrt Linux-4.14.101 114 114 Image Type: MIPS Linux Kernel Image (lzma compressed) 115 - Data Size: 2010110Bytes = 1.9MB27 + Data Size: 1908285 Bytes = 1.8 MB 116 116 Load Address: 80001000 117 117 Entry Point: 80001000 118 -.............................. .Verifying Checksum ... OK30 +.............................. Verifying Checksum ... OK 119 119 Uncompressing Kernel Image ... OK 120 120 No initrd 121 121 ## Transferring control to Linux (at address 80001000) ... ... ... @@ -123,7 +123,7 @@ 123 123 124 124 Starting kernel ... 125 125 126 -[ 0.000000] Linux version 4.14.1 41 () (gcc version 7.4.0 (OpenWrt GCC 7.4.0 r10942-9bebafcb5d)) #0 SMP SunSep1 06:04:50201938 +[ 0.000000] Linux version 4.14.101 () (gcc version 7.4.0 (OpenWrt GCC 7.4.0 r9033-cbee2131d6)) #0 SMP Sat Feb 16 05:28:27 2019 127 127 [ 0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3 128 128 [ 0.000000] bootconsole [early0] enabled 129 129 [ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc) ... ... @@ -142,16 +142,16 @@ 142 142 [ 0.000000] Early memory node ranges 143 143 [ 0.000000] node 0: [mem 0x0000000000000000-0x000000000fffffff] 144 144 [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff] 145 -[ 0.000000] random: get_random_bytes called from start_kernel+0x9 c/0x4d8with crng_init=0146 -[ 0.000000] percpu: Embedded 14 pages/cpu s26 064r8192 d23088u57344147 -[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 6 496057 +[ 0.000000] random: get_random_bytes called from start_kernel+0x90/0x4a4 with crng_init=0 58 +[ 0.000000] percpu: Embedded 14 pages/cpu @8120f000 s26192 r8192 d22960 u57344 59 +[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 65024 148 148 [ 0.000000] Kernel command line: console=ttyS0,115200n8 rootfstype=squashfs,jffs2 149 149 [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) 150 150 [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) 151 151 [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) 152 -[ 0.000000] Writing ErrCtl register=0002c42 0153 -[ 0.000000] Readback ErrCtl register=0002c42 0154 -[ 0.000000] Memory: 25 1700K/262144K available (4796K kernel code, 251K rwdata, 1040K rodata,1260K init, 254K bss,10444K reserved, 0K cma-reserved, 0K highmem)64 +[ 0.000000] Writing ErrCtl register=0002c42c 65 +[ 0.000000] Readback ErrCtl register=0002c42c 66 +[ 0.000000] Memory: 253304K/262144K available (4502K kernel code, 233K rwdata, 1000K rodata, 268K init, 248K bss, 8840K reserved, 0K cma-reserved, 0K highmem) 155 155 [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 156 156 [ 0.000000] Hierarchical RCU implementation. 157 157 [ 0.000000] NR_IRQS: 256 ... ... @@ -159,244 +159,210 @@ 159 159 [ 0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns 160 160 [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4343773742 ns 161 161 [ 0.000009] sched_clock: 32 bits at 440MHz, resolution 2ns, wraps every 4880645118ns 162 -[ 0.007802] Calibrating delay loop... 586.13 BogoMIPS (lpj=2930688) 163 -[ 0.073969] pid_max: default: 32768 minimum: 301 164 -[ 0.078775] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) 165 -[ 0.085284] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) 166 -[ 0.094340] Hierarchical SRCU implementation. 167 -[ 0.099495] smp: Bringing up secondary CPUs ... 168 -[ 0.114811] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. 169 -[ 0.114820] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes 170 -[ 0.114831] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. 171 -[ 0.114963] CPU1 revision is: 0001992f (MIPS 1004Kc) 172 -[ 0.164211] Synchronize counters for CPU 1: done. 173 -[ 0.208189] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. 174 -[ 0.208197] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes 175 -[ 0.208206] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. 176 -[ 0.208284] CPU2 revision is: 0001992f (MIPS 1004Kc) 177 -[ 0.255179] Synchronize counters for CPU 2: done. 178 -[ 0.295789] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. 179 -[ 0.295797] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes 180 -[ 0.295805] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. 181 -[ 0.295885] CPU3 revision is: 0001992f (MIPS 1004Kc) 182 -[ 0.340367] Synchronize counters for CPU 3: done. 183 -[ 0.370232] smp: Brought up 1 node, 4 CPUs 184 -[ 0.378204] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns 185 -[ 0.388001] futex hash table entries: 1024 (order: 3, 32768 bytes) 186 -[ 0.394408] pinctrl core: initialized pinctrl subsystem 187 -[ 0.401009] NET: Registered protocol family 16 188 -[ 0.415266] pull PCIe RST: RALINK_RSTCTRL = 4000000 189 -[ 0.720548] release PCIe RST: RALINK_RSTCTRL = 7000000 190 -[ 0.725598] ***** Xtal 40MHz ***** 191 -[ 0.728952] release PCIe RST: RALINK_RSTCTRL = 7000000 192 -[ 0.734049] Port 0 N_FTS = 1b102800 193 -[ 0.737517] Port 1 N_FTS = 1b102800 194 -[ 0.740963] Port 2 N_FTS = 1b102800 195 -[ 1.896358] PCIE2 no card, disable it(RST&CLK) 196 -[ 1.900719] -> 21007f2 197 -[ 1.903123] PCIE0 enabled 198 -[ 1.905712] PCIE1 enabled 199 -[ 1.908316] PCI host bridge /pcie@1e140000 ranges: 200 -[ 1.913096] MEM 0x0000000060000000..0x000000006fffffff 201 -[ 1.918245] IO 0x000000001e160000..0x000000001e16ffff 202 -[ 1.923451] PCI coherence region base: 0xbfbf8000, mask/settings: 0x60000000 203 -[ 1.939415] mt7621_gpio 1e000600.gpio: registering 32 gpios 204 -[ 1.945254] mt7621_gpio 1e000600.gpio: registering 32 gpios 205 -[ 1.950961] mt7621_gpio 1e000600.gpio: registering 32 gpios 206 -[ 1.958178] PCI host bridge to bus 0000:00 207 -[ 1.962213] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff] 208 -[ 1.969068] pci_bus 0000:00: root bus resource [io 0xffffffff] 209 -[ 1.974896] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0] 210 -[ 1.981655] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] 211 -[ 1.990318] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring 212 -[ 1.998262] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring 213 -[ 2.007510] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000] 214 -[ 2.014070] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000] 215 -[ 2.020937] pci 0000:00:01.0: BAR 0: no space for [mem size 0x80000000] 216 -[ 2.027521] pci 0000:00:01.0: BAR 0: failed to assign [mem size 0x80000000] 217 -[ 2.034415] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff] 218 -[ 2.041173] pci 0000:00:01.0: BAR 8: assigned [mem 0x60100000-0x601fffff] 219 -[ 2.047897] pci 0000:00:00.0: BAR 1: assigned [mem 0x60200000-0x6020ffff] 220 -[ 2.054657] pci 0000:00:01.0: BAR 1: assigned [mem 0x60210000-0x6021ffff] 221 -[ 2.061377] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit] 222 -[ 2.068661] pci 0000:00:00.0: PCI bridge to [bus 01] 223 -[ 2.073551] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff] 224 -[ 2.080327] pci 0000:02:00.0: BAR 0: assigned [mem 0x60100000-0x601fffff 64bit] 225 -[ 2.087559] pci 0000:00:01.0: PCI bridge to [bus 02] 226 -[ 2.092502] pci 0000:00:01.0: bridge window [mem 0x60100000-0x601fffff] 227 -[ 2.100582] clocksource: Switched to clocksource GIC 228 -[ 2.107275] NET: Registered protocol family 2 229 -[ 2.112196] TCP established hash table entries: 2048 (order: 1, 8192 bytes) 230 -[ 2.119081] TCP bind hash table entries: 2048 (order: 2, 16384 bytes) 231 -[ 2.125539] TCP: Hash tables configured (established 2048 bind 2048) 232 -[ 2.131955] UDP hash table entries: 256 (order: 1, 8192 bytes) 233 -[ 2.137713] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) 234 -[ 2.144212] NET: Registered protocol family 1 235 -[ 2.380532] 4 CPUs re-calibrate udelay(lpj = 2924544) 236 -[ 2.387039] Crashlog allocated RAM at address 0x3f00000 237 -[ 2.392460] workingset: timestamp_bits=14 max_order=16 bucket_order=2 238 -[ 2.408000] squashfs: version 4.0 (2009/01/31) Phillip Lougher 239 -[ 2.413806] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. 240 -[ 2.425815] random: fast init done 241 -[ 2.430745] io scheduler noop registered 242 -[ 2.434579] io scheduler deadline registered (default) 243 -[ 2.440747] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled 244 -[ 2.448257] console [ttyS0] disabled 245 -[ 2.451855] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 19, base_baud = 3125000) is a 16550A 246 -[ 2.460836] console [ttyS0] enabled 247 -[ 2.460836] console [ttyS0] enabled 248 -[ 2.467691] bootconsole [early0] disabled 249 -[ 2.467691] bootconsole [early0] disabled 250 -[ 2.477567] MediaTek Nand driver init, version v2.1 Fix AHB virt2phys error 251 -[ 2.484816] Enable NFI Clock 252 -[ 2.487689] # MTK NAND # : Use HW ECC 253 -[ 2.491382] Device not found, ID: c2f1 254 -[ 2.495110] Not Support this Device! 255 -[ 2.498835] chip_mode=00000001 256 -[ 2.501893] Support this Device in MTK table! c2f1 257 -[ 2.506840] [NAND]select ecc bit:4, sparesize :64 spare_per_sector=16 258 -[ 2.513320] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xf1 259 -[ 2.519642] nand: Macronix NAND 128MiB 3,3V 8-bit 260 -[ 2.524347] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 261 -[ 2.531927] Scanning device for bad blocks 262 -[ 2.819771] 7 fixed-partitions partitions found on MTD device MT7621-NAND 263 -[ 2.826546] Creating 7 MTD partitions on "MT7621-NAND": 264 -[ 2.831774] 0x000000000000-0x000000080000 : "uboot" 265 -[ 2.837706] 0x000000080000-0x0000000c0000 : "uboot_env" 266 -[ 2.843891] 0x0000000c0000-0x000000100000 : "factory" 267 -[ 2.849892] 0x000000100000-0x000000140000 : "s_env" 268 -[ 2.855720] 0x000000140000-0x000000180000 : "devinfo" 269 -[ 2.861732] 0x000000180000-0x000002980000 : "firmware1" 270 -[ 2.870032] 0x000002980000-0x000005180000 : "firmware2" 271 -[ 2.877154] 1 uboot-env-boot_part partitions found on MTD device firmware2 272 -[ 2.884061] 0x000002980000-0x000005180000 : "firmware" 273 -[ 3.438509] 2 uimage-fw partitions found on MTD device firmware 274 -[ 3.444473] 0x000002980000-0x000002b80000 : "kernel" 275 -[ 3.450603] 0x000002b80000-0x000005180000 : "ubi" 276 -[ 3.456742] [mtk_nand] probe successfully! 277 -[ 3.461570] Signature matched and data read! 278 -[ 3.465818] load_fact_bbt success 1023 279 -[ 3.470276] libphy: Fixed MDIO Bus: probed 280 -[ 3.542951] mtd_read_prop_mac: find prop "hw_mac_addr" in devinfo(max 0x40000) from 0x0 281 -[ 3.550970] mtd_read_prop_mac: hw_mac_addr= 282 -[ 3.556774] libphy: mdio: probed 283 -[ 4.961009] mtk_soc_eth 1e100000.ethernet: loaded mt7530 driver 284 -[ 4.967662] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 21 285 -[ 4.978262] NET: Registered protocol family 10 286 -[ 4.984286] Segment Routing with IPv6 287 -[ 4.988020] NET: Registered protocol family 17 288 -[ 4.992556] 8021q: 802.1Q VLAN Support v1.8 289 -[ 4.999621] UBI: auto-attach mtd9 290 -[ 5.003015] ubi0: attaching mtd9 291 -[ 5.033798] UBI: EOF marker found, PEBs from 25 will be erased 292 -[ 5.039967] ubi0: scanning is finished 293 -[ 5.081872] ubi0: volume 1 ("rootfs_data") re-sized from 9 to 258 LEBs 294 -[ 5.089203] ubi0: attached mtd9 (name "ubi", size 38 MiB) 295 -[ 5.094644] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes 296 -[ 5.101543] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 297 -[ 5.108298] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 298 -[ 5.115245] ubi0: good PEBs: 297, bad PEBs: 7, corrupted PEBs: 0 299 -[ 5.121247] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128 300 -[ 5.128436] ubi0: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 301 -[ 5.137541] ubi0: available PEBs: 0, total reserved PEBs: 297, PEBs reserved for bad PEB handling: 13 302 -[ 5.146764] ubi0: background thread "ubi_bgt0d" started, PID 378 303 -[ 5.148847] block ubiblock0_0: created from ubi0:0(rootfs) 304 -[ 5.158262] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem 305 -[ 5.165234] hctosys: unable to open rtc device (rtc0) 306 -[ 5.183831] VFS: Mounted root (squashfs filesystem) readonly on device 254:0. 307 -[ 5.195491] Freeing unused kernel memory: 1260K 308 -[ 5.200022] This architecture does not have kernel memory protection. 309 -[ 5.783744] init: Console is alive 310 -[ 5.787378] init: - watchdog - 311 -[ 6.295000] mtk_soc_eth 1e100000.ethernet eth0: port 1 link up 312 -[ 6.502425] kmodloader: loading kernel modules from /etc/modules-boot.d/* 313 -[ 6.591413] usbcore: registered new interface driver usbfs 314 -[ 6.596966] usbcore: registered new interface driver hub 315 -[ 6.602453] usbcore: registered new device driver usb 316 -[ 6.615285] SCSI subsystem initialized 317 -[ 6.626976] xhci-mtk 1e1c0000.xhci: 1e1c0000.xhci supply vbus not found, using dummy regulator 318 -[ 6.635689] xhci-mtk 1e1c0000.xhci: 1e1c0000.xhci supply vusb33 not found, using dummy regulator 319 -[ 6.644627] xhci-mtk 1e1c0000.xhci: xHCI Host Controller 320 -[ 6.649947] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 1 321 -[ 6.660739] xhci-mtk 1e1c0000.xhci: hcc params 0x01401198 hci version 0x96 quirks 0x0000000000210010 322 -[ 6.669906] xhci-mtk 1e1c0000.xhci: irq 20, io mem 0x1e1c0000 323 -[ 6.676639] hub 1-0:1.0: USB hub found 324 -[ 6.680467] hub 1-0:1.0: 2 ports detected 325 -[ 6.685052] xhci-mtk 1e1c0000.xhci: xHCI Host Controller 326 -[ 6.690366] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 2 327 -[ 6.697886] xhci-mtk 1e1c0000.xhci: Host supports USB 3.0 SuperSpeed 328 -[ 6.704507] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. 329 -[ 6.713446] hub 2-0:1.0: USB hub found 330 -[ 6.717275] hub 2-0:1.0: 1 port detected 331 -[ 6.727313] usbcore: registered new interface driver usb-storage 332 -[ 6.733578] kmodloader: done loading kernel modules from /etc/modules-boot.d/* 333 -[ 6.750877] init: - preinit - 334 -[ 7.180814] usb 2-1: new SuperSpeed USB device number 2 using xhci-mtk 335 -[ 7.212805] random: procd: uninitialized urandom read (4 bytes read) 336 -[ 7.212971] usb-storage 2-1:1.0: USB Mass Storage device detected 337 -[ 7.225920] scsi host0: usb-storage 2-1:1.0 338 -[ 7.366240] mtk_soc_eth 1e100000.ethernet: PPE started 74 +[ 0.007805] Calibrating delay loop... 586.13 BogoMIPS (lpj=2930688) 75 +[ 0.073978] pid_max: default: 32768 minimum: 301 76 +[ 0.078744] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) 77 +[ 0.085252] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) 78 +[ 0.094034] Hierarchical SRCU implementation. 79 +[ 0.099185] smp: Bringing up secondary CPUs ... 80 +[ 0.109505] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. 81 +[ 0.109515] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes 82 +[ 0.109526] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. 83 +[ 0.109664] CPU1 revision is: 0001992f (MIPS 1004Kc) 84 +[ 0.163934] Synchronize counters for CPU 1: done. 85 +[ 0.203356] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. 86 +[ 0.203365] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes 87 +[ 0.203372] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. 88 +[ 0.203446] CPU2 revision is: 0001992f (MIPS 1004Kc) 89 +[ 0.255085] Synchronize counters for CPU 2: done. 90 +[ 0.290669] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. 91 +[ 0.290678] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes 92 +[ 0.290686] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. 93 +[ 0.290767] CPU3 revision is: 0001992f (MIPS 1004Kc) 94 +[ 0.340270] Synchronize counters for CPU 3: done. 95 +[ 0.370137] smp: Brought up 1 node, 4 CPUs 96 +[ 0.377732] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns 97 +[ 0.387523] futex hash table entries: 1024 (order: 3, 32768 bytes) 98 +[ 0.393811] pinctrl core: initialized pinctrl subsystem 99 +[ 0.400270] NET: Registered protocol family 16 100 +[ 0.423063] mt7621_gpio 1e000600.gpio: registering 32 gpios 101 +[ 0.428878] mt7621_gpio 1e000600.gpio: registering 32 gpios 102 +[ 0.434658] mt7621_gpio 1e000600.gpio: registering 32 gpios 103 +[ 0.442956] clocksource: Switched to clocksource GIC 104 +[ 0.449425] NET: Registered protocol family 2 105 +[ 0.454419] TCP established hash table entries: 2048 (order: 1, 8192 bytes) 106 +[ 0.461303] TCP bind hash table entries: 2048 (order: 2, 16384 bytes) 107 +[ 0.467778] TCP: Hash tables configured (established 2048 bind 2048) 108 +[ 0.474212] UDP hash table entries: 256 (order: 1, 8192 bytes) 109 +[ 0.479979] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) 110 +[ 0.486452] NET: Registered protocol family 1 111 +[ 0.722896] 4 CPUs re-calibrate udelay(lpj = 2924544) 112 +[ 0.729302] Crashlog allocated RAM at address 0x3f00000 113 +[ 0.734701] workingset: timestamp_bits=30 max_order=16 bucket_order=0 114 +[ 0.748195] squashfs: version 4.0 (2009/01/31) Phillip Lougher 115 +[ 0.753975] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. 116 +[ 0.765554] random: fast init done 117 +[ 0.770526] io scheduler noop registered 118 +[ 0.774396] io scheduler deadline registered (default) 119 +[ 0.780409] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled 120 +[ 0.788106] console [ttyS0] disabled 121 +[ 0.791645] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 18, base_baud = 3125000) is a 16550A 122 +[ 0.800653] console [ttyS0] enabled 123 +[ 0.800653] console [ttyS0] enabled 124 +[ 0.807523] bootconsole [early0] disabled 125 +[ 0.807523] bootconsole [early0] disabled 126 +[ 0.816146] cacheinfo: Unable to detect cache hierarchy for CPU 0 127 +[ 0.823038] MediaTek Nand driver init, version v2.1 Fix AHB virt2phys error 128 +[ 0.830119] Enable NFI Clock 129 +[ 0.833044] # MTK NAND # : Use HW ECC 130 +[ 0.836708] Device not found, ID: c2f1 131 +[ 0.840433] Not Support this Device! 132 +[ 0.844177] chip_mode=00000001 133 +[ 0.847217] Support this Device in MTK table! c2f1 134 +[ 0.852163] [NAND]select ecc bit:4, sparesize :64 spare_per_sector=16 135 +[ 0.858632] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xf1 136 +[ 0.864966] nand: Macronix NAND 128MiB 3,3V 8-bit 137 +[ 0.869648] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 138 +[ 0.877212] Scanning device for bad blocks 139 +[ 0.898080] Bad eraseblock 71 at 0x0000008e0000 140 +[ 0.967695] Bad eraseblock 349 at 0x000002ba0000 141 +[ 0.978049] Bad eraseblock 374 at 0x000002ec0000 142 +[ 0.987933] Bad eraseblock 397 at 0x0000031a0000 143 +[ 1.006268] Bad eraseblock 456 at 0x000003900000 144 +[ 1.021533] Bad eraseblock 502 at 0x000003ec0000 145 +[ 1.034940] Bad eraseblock 540 at 0x000004380000 146 +[ 1.050681] Bad eraseblock 588 at 0x000004980000 147 +[ 1.107262] Bad eraseblock 810 at 0x000006540000 148 +[ 1.129339] Bad eraseblock 885 at 0x000006ea0000 149 +[ 1.166421] 7 fixed-partitions partitions found on MTD device MT7621-NAND 150 +[ 1.173195] Creating 7 MTD partitions on "MT7621-NAND": 151 +[ 1.178405] 0x000000000000-0x000000080000 : "uboot" 152 +[ 1.184240] 0x000000080000-0x0000000c0000 : "uboot_env" 153 +[ 1.190298] 0x0000000c0000-0x000000100000 : "factory" 154 +[ 1.196219] 0x000000100000-0x000000140000 : "s_env" 155 +[ 1.201900] 0x000000140000-0x000000180000 : "devinfo" 156 +[ 1.207850] 0x000000180000-0x000002980000 : "firmware1" 157 +[ 1.216116] 0x000002980000-0x000005180000 : "firmware2" 158 +[ 1.223224] 1 uboot-env-boot_part partitions found on MTD device firmware2 159 +[ 1.230090] 0x000002980000-0x000005180000 : "firmware" 160 +[ 1.784436] 2 uimage-fw partitions found on MTD device firmware 161 +[ 1.790355] 0x000002980000-0x000002b60000 : "kernel" 162 +[ 1.796251] 0x000002b60000-0x000005180000 : "ubi" 163 +[ 1.802130] [mtk_nand] probe successfully! 164 +[ 1.806957] Signature matched and data read! 165 +[ 1.811205] load_fact_bbt success 1023 166 +[ 1.815701] libphy: Fixed MDIO Bus: probed 167 +[ 1.885315] mtd_read_prop_mac: find prop "hw_mac_addr" in devinfo(max 0x40000) from 0x0 168 +[ 1.893332] mtd_read_prop_mac: hw_mac_addr=XX:YY:ZZ:00:11:33 169 +[ 1.899142] libphy: mdio: probed 170 +[ 3.302014] mtk_soc_eth 1e100000.ethernet: loaded mt7530 driver 171 +[ 3.308669] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 20 172 +[ 3.319426] NET: Registered protocol family 10 173 +[ 3.325219] Segment Routing with IPv6 174 +[ 3.328949] NET: Registered protocol family 17 175 +[ 3.333457] 8021q: 802.1Q VLAN Support v1.8 176 +[ 3.340506] UBI: auto-attach mtd9 177 +[ 3.343893] ubi0: attaching mtd9 178 +[ 3.363286] UBI: EOF marker found, PEBs from 15 will be erased 179 +[ 3.369474] ubi0: scanning is finished 180 +[ 3.411360] ubi0: volume 1 ("rootfs_data") re-sized from 9 to 269 LEBs 181 +[ 3.418731] ubi0: attached mtd9 (name "ubi", size 38 MiB) 182 +[ 3.424164] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes 183 +[ 3.431006] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 184 +[ 3.437780] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 185 +[ 3.444725] ubi0: good PEBs: 298, bad PEBs: 7, corrupted PEBs: 0 186 +[ 3.450701] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128 187 +[ 3.457906] ubi0: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 1203044710 188 +[ 3.467015] ubi0: available PEBs: 0, total reserved PEBs: 298, PEBs reserved for bad PEB handling: 13 189 +[ 3.476230] ubi0: background thread "ubi_bgt0d" started, PID 359 190 +[ 3.477972] block ubiblock0_0: created from ubi0:0(rootfs) 191 +[ 3.487716] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem 192 +[ 3.494673] hctosys: unable to open rtc device (rtc0) 193 +[ 3.519930] VFS: Mounted root (squashfs filesystem) readonly on device 254:0. 194 +[ 3.527684] Freeing unused kernel memory: 268K 195 +[ 3.532122] This architecture does not have kernel memory protection. 196 +[ 4.017012] init: Console is alive 197 +[ 4.020616] init: - watchdog - 198 +[ 4.354210] kmodloader: loading kernel modules from /etc/modules-boot.d/* 199 +[ 4.443714] usbcore: registered new interface driver usbfs 200 +[ 4.449260] usbcore: registered new interface driver hub 201 +[ 4.454739] usbcore: registered new device driver usb 202 +[ 4.467426] SCSI subsystem initialized 203 +[ 4.480878] xhci-mtk 1e1c0000.xhci: 1e1c0000.xhci supply vbus not found, using dummy regulator 204 +[ 4.489588] xhci-mtk 1e1c0000.xhci: 1e1c0000.xhci supply vusb33 not found, using dummy regulator 205 +[ 4.498507] xhci-mtk 1e1c0000.xhci: xHCI Host Controller 206 +[ 4.503843] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 1 207 +[ 4.523114] xhci-mtk 1e1c0000.xhci: hcc params 0x01401198 hci version 0x96 quirks 0x0000000000210010 208 +[ 4.532283] xhci-mtk 1e1c0000.xhci: irq 19, io mem 0x1e1c0000 209 +[ 4.538971] hub 1-0:1.0: USB hub found 210 +[ 4.542796] hub 1-0:1.0: 2 ports detected 211 +[ 4.547400] xhci-mtk 1e1c0000.xhci: xHCI Host Controller 212 +[ 4.552722] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 2 213 +[ 4.560210] xhci-mtk 1e1c0000.xhci: Host supports USB 3.0 SuperSpeed 214 +[ 4.560493] mtk_soc_eth 1e100000.ethernet eth0: port 4 link up 215 +[ 4.566816] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. 216 +[ 4.581320] hub 2-0:1.0: USB hub found 217 +[ 4.585161] hub 2-0:1.0: 1 port detected 218 +[ 4.593449] usbcore: registered new interface driver usb-storage 219 +[ 4.599693] kmodloader: done loading kernel modules from /etc/modules-boot.d/* 220 +[ 4.623240] init: - preinit - 221 +[ 5.073028] usb 1-2: new high-speed USB device number 2 using xhci-mtk 222 +[ 5.221107] mtk_soc_eth 1e100000.ethernet: PPE started 223 +[ 5.255985] usb-storage 1-2:1.0: USB Mass Storage device detected 224 +[ 5.262845] scsi host0: usb-storage 1-2:1.0 339 339 Press the [f] key and hit [enter] to enter failsafe mode 340 340 Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level 341 -[ 10.582466] UBIFS (ubi0:1): default file-system created 342 -[ 10.589130] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 496 343 -[ 10.700430] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data" 344 -[ 10.708276] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes 345 -[ 10.718161] UBIFS (ubi0:1): FS size: 31490048 bytes (30 MiB, 248 LEBs), journal size 1523712 bytes (1 MiB, 12 LEBs) 346 -[ 10.728565] UBIFS (ubi0:1): reserved for root: 1487352 bytes (1452 KiB) 347 -[ 10.735166] UBIFS (ubi0:1): media format: w4/r0 (latest is w5/r0), UUID , small LPT model 348 -[ 10.749347] mount_root: overlay filesystem has not been fully initialized yet 349 -[ 10.756981] mount_root: switching to ubifs overlay 350 -[ 10.781065] urandom-seed: Seed file not found (/etc/urandom.seed) 351 -[ 10.861172] mtk_soc_eth 1e100000.ethernet: 0x100 = 0x6060000c, 0x10c = 0x80818 352 -[ 10.876085] procd: - early - 353 -[ 10.879061] procd: - watchdog - 354 -[ 11.550737] procd: - watchdog - 355 -[ 11.554202] procd: - ubus - 356 -[ 11.583502] random: ubusd: uninitialized urandom read (4 bytes read) 357 -[ 11.611421] random: ubusd: uninitialized urandom read (4 bytes read) 358 -[ 11.618117] random: ubusd: uninitialized urandom read (4 bytes read) 359 -[ 11.625387] procd: - init - 227 +[ 5.312718] random: procd: uninitialized urandom read (4 bytes read) 228 +[ 6.273781] scsi 0:0:0:0: Direct-Access SanDisk Ultra Fit 1.00 PQ: 0 ANSI: 6 229 +[ 6.283479] sd 0:0:0:0: [sda] 60063744 512-byte logical blocks: (30.8 GB/28.6 GiB) 230 +[ 6.291556] sd 0:0:0:0: [sda] Write Protect is off 231 +[ 6.297040] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA 232 +[ 6.313010] sd 0:0:0:0: [sda] Attached SCSI removable disk 233 +[ 8.450677] UBIFS (ubi0:1): default file-system created 234 +[ 8.457372] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 474 235 +[ 8.568317] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data" 236 +[ 8.576154] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes 237 +[ 8.586040] UBIFS (ubi0:1): FS size: 32886784 bytes (31 MiB, 259 LEBs), journal size 1650688 bytes (1 MiB, 13 LEBs) 238 +[ 8.596442] UBIFS (ubi0:1): reserved for root: 1553323 bytes (1516 KiB) 239 +[ 8.603051] UBIFS (ubi0:1): media format: w4/r0 (latest is w5/r0), UUID D42C5178-C937-4CB4-94EE-0031FFF6550A, small LPT model 240 +[ 8.617248] mount_root: overlay filesystem has not been fully initialized yet 241 +[ 8.624849] mount_root: switching to ubifs overlay 242 +[ 8.647505] urandom-seed: Seed file not found (/etc/urandom.seed) 243 +[ 8.728797] mtk_soc_eth 1e100000.ethernet: 0x100 = 0x6060000c, 0x10c = 0x80818 244 +[ 8.743450] procd: - early - 245 +[ 8.746426] procd: - watchdog - 246 +[ 9.403107] procd: - watchdog - 247 +[ 9.406559] procd: - ubus - 248 +[ 9.457080] random: ubusd: uninitialized urandom read (4 bytes read) 249 +[ 9.464255] random: ubusd: uninitialized urandom read (4 bytes read) 250 +[ 9.470985] random: ubusd: uninitialized urandom read (4 bytes read) 251 +[ 9.478186] procd: - init - 360 360 Please press Enter to activate this console. 361 -[ 12.046531] kmodloader: loading kernel modules from /etc/modules.d/* 362 -[ 12.057746] ip6_tables: (C) 2000-2006 Netfilter Core Team 363 -[ 12.069204] Loading modules backported from Linux version v5.3-rc4-0-gd45331b00ddb 364 -[ 12.076775] Backport generated by backports.git v5.3-rc4-1-0-g4ec72687 365 -[ 12.085114] ip_tables: (C) 2000-2006 Netfilter Core Team 366 -[ 12.096731] nf_conntrack version 0.5.0 (4096 buckets, 16384 max) 367 -[ 12.127574] urngd: v1.0.0 started. 368 -[ 12.145053] xt_time: kernel timezone is -0000 369 -[ 12.214244] bus=0x1, slot = 0x0, irq=0x0 370 -[ 12.218201] PCI: Enabling device 0000:00:00.0 (0004 -> 0006) 371 -[ 12.241178] mt7615e 0000:01:00.0: HW/SW Version: 0x8a108a10, Build Time: 20180518100604a 372 -[ 12.241178] 373 -[ 12.266469] random: crng init done 374 -[ 12.269877] random: 6 urandom warning(s) missed due to ratelimiting 375 -[ 12.456236] mt7615e 0000:01:00.0: N9 Firmware Version: _reserved_, Build Time: 20190103180756 376 -[ 12.471995] mt7615e 0000:01:00.0: CR4 Firmware Version: _reserved_, Build Time: 20181207140436 377 -+ýýrýýýýýýýbus=0x2, slot = 0x1, irq=0x0 378 -[ 20.131310] PCI: Enabling device 0000:00:01.0 (0004 -> 0006) 379 -[ 20.161193] mt7615e 0000:02:00.0: HW/SW Version: 0x8a108a10, Build Time: 20180518100604a 380 -[ 20.161193] 381 -[ 20.185604] mt7615e 0000:02:00.0: N9 Firmware Version: _reserved_, Build Time: 20190103180756 382 -[ 20.200746] mt7615e 0000:02:00.0: CR4 Firmware Version: _reserved_, Build Time: 20181207140436 383 -[ 27.852570] PPP generic driver version 2.4.2 384 -[ 27.858358] NET: Registered protocol family 24 385 -[ 27.866716] kmodloader: done loading kernel modules from /etc/modules.d/* 386 -[ 41.276638] mtk_soc_eth 1e100000.ethernet: PPE started 387 -[ 41.287935] br-lan: port 1(eth0.2) entered blocking state 388 -[ 41.293420] br-lan: port 1(eth0.2) entered disabled state 389 -[ 41.299522] device eth0.2 entered promiscuous mode 390 -[ 41.304484] device eth0 entered promiscuous mode 391 -[ 41.311947] br-lan: port 1(eth0.2) entered blocking state 392 -[ 41.317384] br-lan: port 1(eth0.2) entered forwarding state 393 -[ 41.323511] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready 394 -[ 42.321086] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready 253 +[ 9.714720] kmodloader: loading kernel modules from /etc/modules.d/* 254 +[ 9.724486] ip6_tables: (C) 2000-2006 Netfilter Core Team 255 +[ 9.738298] ip_tables: (C) 2000-2006 Netfilter Core Team 256 +[ 9.749820] nf_conntrack version 0.5.0 (4096 buckets, 16384 max) 257 +[ 9.790837] xt_time: kernel timezone is -0000 258 +[ 9.801201] PPP generic driver version 2.4.2 259 +[ 9.806822] NET: Registered protocol family 24 260 +[ 9.813785] kmodloader: done loading kernel modules from /etc/modules.d/* 261 +[ 10.951148] urandom_read: 5 callbacks suppressed 262 +[ 10.951161] random: jshn: uninitialized urandom read (4 bytes read) 263 +[ 16.501675] mtk_soc_eth 1e100000.ethernet: PPE started 264 +[ 16.512395] br-lan: port 1(eth0.2) entered blocking state 265 +[ 16.517965] br-lan: port 1(eth0.2) entered disabled state 266 +[ 16.523873] device eth0.2 entered promiscuous mode 267 +[ 16.528744] device eth0 entered promiscuous mode 268 +[ 16.537326] br-lan: port 1(eth0.2) entered blocking state 269 +[ 16.542760] br-lan: port 1(eth0.2) entered forwarding state 270 +[ 16.548768] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready 271 +[ 17.553672] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready 272 +[ 21.883773] random: crng init done 273 + 395 395 396 396 276 +BusyBox v1.30.1 () built-in shell (ash) 397 397 398 -BusyBox v1.31.0 () built-in shell (ash) 399 - 400 400 _______ ________ __ 401 401 | |.-----.-----.-----.| | | |.----.| |_ 402 402 | - || _ | -__| || | | || _|| _| ... ... @@ -403,7 +403,7 @@ 403 403 |_______|| __|_____|__|__||________||__| |____| 404 404 |__| W I R E L E S S F R E E D O M 405 405 ----------------------------------------------------- 406 - OpenWrt SNAPSHOT, r 10942-9bebafcb5d284 + OpenWrt SNAPSHOT, r9254+122-3b40121530 407 407 ----------------------------------------------------- 408 408 === WARNING! ===================================== 409 409 There is no root password defined on this device! ... ... @@ -410,344 +410,15 @@ 410 410 Use the "passwd" command to set up a new password 411 411 in order to prevent unauthorized SSH logins. 412 412 -------------------------------------------------- 413 -root@OpenWrt:/# ifconfig -a 414 -br-lan Link encap:Ethernet HWaddr 415 - inet addr:192.168.1.1 Bcast:192.168.1.255 Mask:255.255.255.0 416 - inet6 addr: fde0:62db:5134::1/60 Scope:Global 417 - inet6 addr: fe80::/64 Scope:Link 418 - UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 419 - RX packets:41 errors:0 dropped:0 overruns:0 frame:0 420 - TX packets:13 errors:0 dropped:0 overruns:0 carrier:0 421 - collisions:0 txqueuelen:1000 422 - RX bytes:8012 (7.8 KiB) TX bytes:2126 (2.0 KiB) 423 - 424 -eth0 Link encap:Ethernet HWaddr 425 - inet6 addr: fe80::/64 Scope:Link 426 - UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 427 - RX packets:102 errors:0 dropped:0 overruns:0 frame:0 428 - TX packets:47 errors:0 dropped:0 overruns:0 carrier:0 429 - collisions:0 txqueuelen:1000 430 - RX bytes:19418 (18.9 KiB) TX bytes:8199 (8.0 KiB) 431 - Interrupt:21 432 - 433 -eth0.1 Link encap:Ethernet HWaddr 434 - inet6 addr: fe80::/64 Scope:Link 435 - UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 436 - RX packets:0 errors:0 dropped:0 overruns:0 frame:0 437 - TX packets:20 errors:0 dropped:0 overruns:0 carrier:0 438 - collisions:0 txqueuelen:1000 439 - RX bytes:0 (0.0 B) TX bytes:3368 (3.2 KiB) 440 - 441 -eth0.2 Link encap:Ethernet HWaddr 442 - UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 443 - RX packets:41 errors:0 dropped:0 overruns:0 frame:0 444 - TX packets:13 errors:0 dropped:0 overruns:0 carrier:0 445 - collisions:0 txqueuelen:1000 446 - RX bytes:8012 (7.8 KiB) TX bytes:2126 (2.0 KiB) 447 - 448 -lo Link encap:Local Loopback 449 - inet addr:127.0.0.1 Mask:255.0.0.0 450 - inet6 addr: ::1/128 Scope:Host 451 - UP LOOPBACK RUNNING MTU:65536 Metric:1 452 - RX packets:28 errors:0 dropped:0 overruns:0 frame:0 453 - TX packets:28 errors:0 dropped:0 overruns:0 carrier:0 454 - collisions:0 txqueuelen:1000 455 - RX bytes:1904 (1.8 KiB) TX bytes:1904 (1.8 KiB) 456 - 457 -wlan0 Link encap:Ethernet HWaddr 458 - BROADCAST MULTICAST MTU:1500 Metric:1 459 - RX packets:0 errors:0 dropped:0 overruns:0 frame:0 460 - TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 461 - collisions:0 txqueuelen:1000 462 - RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) 463 - 464 -wlan1 Link encap:Ethernet HWaddr 465 - BROADCAST MULTICAST MTU:1500 Metric:1 466 - RX packets:0 errors:0 dropped:0 overruns:0 frame:0 467 - TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 468 - collisions:0 txqueuelen:1000 469 - RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) 470 - 471 -root@OpenWrt:/# ls -l 472 -drwxr-xr-x 2 root root 778 Sep 1 06:04 bin 473 -drwxr-xr-x 4 root root 1300 Sep 1 06:05 dev 474 -drwxr-xr-x 1 root root 512 Sep 1 06:05 etc 475 --rwxr-xr-x 1 root root 78 Dec 30 2018 init 476 -drwxr-xr-x 11 root root 426 Sep 1 06:04 lib 477 -drwxr-xr-x 2 root root 3 Sep 1 06:04 mnt 478 -drwxr-xr-x 4 root root 360 Sep 1 06:05 overlay 479 -dr-xr-xr-x 73 root root 0 Jan 1 1970 proc 480 -drwxr-xr-x 16 root root 223 Sep 1 06:04 rom 481 -drwxr-xr-x 2 root root 3 Sep 1 06:04 root 482 -drwxr-xr-x 2 root root 822 Sep 1 06:04 sbin 483 -dr-xr-xr-x 11 root root 0 Jan 1 1970 sys 484 -drwxrwxrwt 15 root root 380 Sep 1 06:05 tmp 485 -drwxr-xr-x 7 root root 89 Sep 1 06:04 usr 486 -lrwxrwxrwx 1 root root 3 Sep 1 06:04 var -> tmp 487 -drwxr-xr-x 2 root root 3 Sep 1 06:04 www 488 -root@OpenWrt:/# ps 489 - PID USER VSZ STAT COMMAND 490 - 1 root 1576 S /sbin/procd 491 - 2 root 0 SW [kthreadd] 492 - 3 root 0 IW [kworker/0:0] 493 - 4 root 0 IW< [kworker/0:0H] 494 - 5 root 0 IW [kworker/u8:0] 495 - 6 root 0 IW< [mm_percpu_wq] 496 - 7 root 0 SW [ksoftirqd/0] 497 - 8 root 0 IW [rcu_sched] 498 - 9 root 0 IW [rcu_bh] 499 - 10 root 0 SW [migration/0] 500 - 11 root 0 SW [cpuhp/0] 501 - 12 root 0 SW [cpuhp/1] 502 - 13 root 0 SW [migration/1] 503 - 14 root 0 SW [ksoftirqd/1] 504 - 16 root 0 IW< [kworker/1:0H] 505 - 17 root 0 SW [cpuhp/2] 506 - 18 root 0 SW [migration/2] 507 - 19 root 0 SW [ksoftirqd/2] 508 - 21 root 0 IW< [kworker/2:0H] 509 - 22 root 0 SW [cpuhp/3] 510 - 23 root 0 SW [migration/3] 511 - 24 root 0 SW [ksoftirqd/3] 512 - 25 root 0 IW [kworker/3:0] 513 - 26 root 0 IW< [kworker/3:0H] 514 - 27 root 0 IW< [netns] 515 - 41 root 0 IW [kworker/u8:3] 516 - 68 root 0 IW [kworker/3:1] 517 - 69 root 0 IW [kworker/2:1] 518 - 138 root 0 IW [kworker/1:1] 519 - 139 root 0 SW [oom_reaper] 520 - 140 root 0 IW< [writeback] 521 - 142 root 0 SW [kcompactd0] 522 - 143 root 0 IW< [crypto] 523 - 145 root 0 IW< [kblockd] 524 - 175 root 0 IW< [watchdogd] 525 - 199 root 0 SW [kswapd0] 526 - 268 root 0 IW< [pencrypt] 527 - 270 root 0 IW< [pdecrypt] 528 - 366 root 0 IW< [ipv6_addrconf] 529 - 378 root 0 SW [ubi_bgt0d] 530 - 383 root 0 IW< [kworker/0:1H] 531 - 384 root 0 IW< [kworker/2:1H] 532 - 385 root 0 IW [kworker/2:2] 533 - 386 root 0 IW< [kworker/3:1H] 534 - 389 root 0 IW< [kworker/1:1H] 535 - 429 root 0 IW [kworker/0:2] 536 - 437 root 0 IW [kworker/1:2] 537 - 453 root 0 SW [scsi_eh_0] 538 - 454 root 0 IW< [scsi_tmf_0] 539 - 455 root 0 SW [usb-storage] 540 - 496 root 0 SW [ubifs_bgt0_1] 541 - 573 root 1220 S /sbin/ubusd 542 - 574 root 1220 S /bin/ash --login 543 - 591 root 1028 S /sbin/urngd 544 - 660 root 0 IW< [cfg80211] 545 - 1012 root 1248 S /sbin/logd -S 64 546 - 1074 dnsmasq 1344 S /usr/sbin/dnsmasq -C /var/etc/dnsmasq.conf.cfg01411c 547 - 1111 root 1080 S /usr/sbin/dropbear -F -P /var/run/dropbear.1.pid -p 548 - 1168 root 1700 S /sbin/netifd 549 - 1204 root 1448 S /usr/sbin/odhcpd 550 - 1360 root 1212 S udhcpc -p /var/run/udhcpc-eth0.1.pid -s /lib/netifd/ 551 - 1361 root 1052 S odhcp6c -s /lib/netifd/dhcpv6.script -P0 -t120 eth0. 552 - 1391 root 1212 S< /usr/sbin/ntpd -n -N -S /usr/sbin/ntpd-hotplug -p 0. 553 - 1720 root 1212 R ps 554 -root@OpenWrt:/etc# ping www.google.co 555 -PING www.google.co (): 56 data bytes 556 -64 bytes from : seq=0 ttl=52 time=4.718 ms 557 -^C 558 ---- www.google.co ping statistics --- 559 -1 packets transmitted, 1 packets received, 0% packet loss 560 -round-trip min/avg/max = 4.718/4.718/4.718 ms 561 -root@OpenWrt:/etc# ping www.google.com 562 -PING www.google.com (): 56 data bytes 563 -64 bytes from : seq=0 ttl=47 time=4.927 ms 564 -64 bytes from : seq=1 ttl=47 time=4.687 ms 565 -^C 566 ---- www.google.com ping statistics --- 567 -2 packets transmitted, 2 packets received, 0% packet loss 568 -round-trip min/avg/max = 4.687/4.807/4.927 ms 569 -root@OpenWrt:/etc# opkg update 570 -Downloading http://downloads.openwrt.org/snapshots/targets/ramips/mt7621/packages/Packages.gz 571 -Updated list of available packages in /var/opkg-lists/openwrt_core 572 -Downloading http://downloads.openwrt.org/snapshots/targets/ramips/mt7621/packages/Packages.sig 573 -Signature check passed. 574 -Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/base/Packages.gz 575 -Updated list of available packages in /var/opkg-lists/openwrt_base 576 -Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/base/Packages.sig 577 -Signature check passed. 578 -Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/Packages.gz 579 -Updated list of available packages in /var/opkg-lists/openwrt_luci 580 -Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/Packages.sig 581 -Signature check passed. 582 -Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/packages/Packages.gz 583 -Updated list of available packages in /var/opkg-lists/openwrt_packages 584 -Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/packages/Packages.sig 585 -Signature check passed. 586 -Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/routing/Packages.gz 587 -Updated list of available packages in /var/opkg-lists/openwrt_routing 588 -Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/routing/Packages.sig 589 -Signature check passed. 590 -Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/telephony/Packages.gz 591 -Updated list of available packages in /var/opkg-lists/openwrt_telephony 592 -Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/telephony/Packages.sig 593 -Signature check passed. 594 -root@OpenWrt:/etc# opkg install luci 595 -Installing luci (git-19.241.65047-dffe9ca-1) to root... 596 -Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/luci_git-19.241.65047-dffe9ca-1_all.ipk 597 -Installing uhttpd (2019-08-17-6b03f960-3) to root... 598 -Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/base/uhttpd_2019-08-17-6b03f960-3_mipsel_24kc.ipk 599 -Installing liblua5.1.5 (5.1.5-5) to root... 600 -Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/base/liblua5.1.5_5.1.5-5_mipsel_24kc.ipk 601 -Installing lua (5.1.5-5) to root... 602 -Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/base/lua_5.1.5-5_mipsel_24kc.ipk 603 -Installing luci-lib-nixio (git-19.241.65047-dffe9ca-1) to root... 604 -Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/luci-lib-nixio_git-19.241.65047-dffe9ca-1_mipsel_24kc.ipk 605 -Installing luci-lib-ip (git-19.241.65047-dffe9ca-1) to root... 606 -Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/luci-lib-ip_git-19.241.65047-dffe9ca-1_mipsel_24kc.ipk 607 -Installing rpcd (2019-06-05-89bfaa42-3) to root... 608 -Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/base/rpcd_2019-06-05-89bfaa42-3_mipsel_24kc.ipk 609 -Installing libubus-lua (2018-10-06-221ce7e7-1) to root... 610 -Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/base/libubus-lua_2018-10-06-221ce7e7-1_mipsel_24kc.ipk 611 -Installing luci-lib-jsonc (git-19.241.65047-dffe9ca-1) to root... 612 -Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/luci-lib-jsonc_git-19.241.65047-dffe9ca-1_mipsel_24kc.ipk 613 -Installing liblucihttp0 (2019-07-05-a34a17d5-1) to root... 614 -Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/liblucihttp0_2019-07-05-a34a17d5-1_mipsel_24kc.ipk 615 -Installing liblucihttp-lua (2019-07-05-a34a17d5-1) to root... 616 -Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/liblucihttp-lua_2019-07-05-a34a17d5-1_mipsel_24kc.ipk 617 -Installing luci-base (git-19.241.65047-dffe9ca-1) to root... 618 -Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/luci-base_git-19.241.65047-dffe9ca-1_mipsel_24kc.ipk 619 -Installing libiwinfo-lua (2019-08-28-a9f95570-1) to root... 620 -Downloading http://downloads.openwrt.org/snapshots/targets/ramips/mt7621/packages/libiwinfo-lua_2019-08-28-a9f95570-1_mipsel_24kc.ipk 621 -Installing luci-mod-status (git-19.241.65047-dffe9ca-1) to root... 622 -Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/luci-mod-status_git-19.241.65047-dffe9ca-1_mipsel_24kc.ipk 623 -Installing luci-mod-system (git-19.241.65047-dffe9ca-1) to root... 624 -Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/luci-mod-system_git-19.241.65047-dffe9ca-1_all.ipk 625 -Installing luci-mod-network (git-19.241.65047-dffe9ca-1) to root... 626 -Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/luci-mod-network_git-19.241.65047-dffe9ca-1_all.ipk 627 -Installing luci-mod-admin-full (git-19.241.65047-dffe9ca-1) to root... 628 -Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/luci-mod-admin-full_git-19.241.65047-dffe9ca-1_all.ipk 629 -Installing luci-theme-bootstrap (git-19.241.65047-dffe9ca-1) to root... 630 -Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/luci-theme-bootstrap_git-19.241.65047-dffe9ca-1_all.ipk 631 -Installing luci-app-firewall (git-19.241.65047-dffe9ca-1) to root... 632 -Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/luci-app-firewall_git-19.241.65047-dffe9ca-1_all.ipk 633 -Installing luci-app-opkg (git-19.241.65047-dffe9ca-1) to root... 634 -Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/luci-app-opkg_git-19.241.65047-dffe9ca-1_all.ipk 635 -Installing luci-proto-ppp (git-19.241.65047-dffe9ca-1) to root... 636 -Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/luci-proto-ppp_git-19.241.65047-dffe9ca-1_all.ipk 637 -Installing luci-proto-ipv6 (git-19.241.65047-dffe9ca-1) to root... 638 -Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/luci-proto-ipv6_git-19.241.65047-dffe9ca-1_all.ipk 639 -Installing rpcd-mod-rrdns (20170710) to root... 640 -Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/rpcd-mod-rrdns_20170710_mipsel_24kc.ipk 641 -Configuring liblucihttp0. 642 -Configuring luci-app-opkg. 643 -Configuring rpcd. 644 -Configuring liblua5.1.5. 645 -Configuring luci-lib-ip. 646 -Configuring libubus-lua. 647 -Configuring libiwinfo-lua. 648 -Configuring lua. 649 -Configuring luci-lib-nixio. 650 -Configuring luci-lib-jsonc. 651 -Configuring liblucihttp-lua. 652 -Configuring luci-base. 653 -Configuring luci-mod-system. 654 -Configuring luci-theme-bootstrap. 655 -Configuring luci-mod-status. 656 -Configuring luci-app-firewall. 657 -Configuring luci-proto-ppp. 658 -Configuring luci-mod-network. 659 -Configuring luci-mod-admin-full. 660 -Configuring luci-proto-ipv6. 661 -Configuring uhttpd. 662 -Configuring rpcd-mod-rrdns. 663 -Configuring luci. 664 -root@OpenWrt:/etc# df -h 291 +root@OpenWrt:/# free 292 + total used free shared buff/cache available 293 +Mem: 253572 23256 224316 60 6000 203516 294 +Swap: 0 0 0 295 +root@OpenWrt:/# df -h 665 665 Filesystem Size Used Available Use% Mounted on 666 -/dev/root 2.8M2.8M 0 100% /rom667 -tmpfs 123. 5M764.0K 122.8M1% /tmp668 -/dev/ubi0_1 2 7.1M1.4M24.3M5% /overlay669 -overlayfs:/overlay 2 7.1M1.4M24.3M5% /297 +/dev/root 1.5M 1.5M 0 100% /rom 298 +tmpfs 123.8M 60.0K 123.8M 0% /tmp 299 +/dev/ubi0_1 28.3M 36.0K 26.8M 0% /overlay 300 +overlayfs:/overlay 28.3M 36.0K 26.8M 0% / 670 670 tmpfs 512.0K 0 512.0K 0% /dev 671 -root@OpenWrt:/etc# [ 2075.963720] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready 672 -[ 2075.973245] br-lan: port 2(wlan0) entered blocking state 673 -[ 2075.978551] br-lan: port 2(wlan0) entered disabled state 674 -[ 2075.984368] device wlan0 entered promiscuous mode 675 -[ 2087.165173] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready 676 -[ 2087.171890] br-lan: port 2(wlan0) entered blocking state 677 -[ 2087.177194] br-lan: port 2(wlan0) entered forwarding state 678 -[ 2096.494533] device wlan0 left promiscuous mode 679 -[ 2096.499322] br-lan: port 2(wlan0) entered disabled state 680 -[ 2097.382887] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready 681 -[ 2097.393568] br-lan: port 2(wlan0) entered blocking state 682 -[ 2097.398924] br-lan: port 2(wlan0) entered disabled state 683 -[ 2097.404922] device wlan0 entered promiscuous mode 684 -[ 2097.409972] br-lan: port 2(wlan0) entered blocking state 685 -[ 2097.415296] br-lan: port 2(wlan0) entered forwarding state 686 -[ 2097.749351] br-lan: port 2(wlan0) entered disabled state 687 -[ 2107.953875] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready 688 -[ 2107.960561] br-lan: port 2(wlan0) entered blocking state 689 -[ 2107.965861] br-lan: port 2(wlan0) entered forwarding state 690 -[ 2117.964353] device wlan0 left promiscuous mode 691 -[ 2117.969130] br-lan: port 2(wlan0) entered disabled state 692 -[ 2118.782586] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready 693 -[ 2118.792816] br-lan: port 2(wlan0) entered blocking state 694 -[ 2118.798173] br-lan: port 2(wlan0) entered disabled state 695 -[ 2118.804171] device wlan0 entered promiscuous mode 696 -[ 2118.809362] br-lan: port 2(wlan0) entered blocking state 697 -[ 2118.814692] br-lan: port 2(wlan0) entered forwarding state 698 -[ 2119.189273] br-lan: port 2(wlan0) entered disabled state 699 -[ 2130.258107] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready 700 -[ 2130.264811] br-lan: port 2(wlan0) entered blocking state 701 -[ 2130.270163] br-lan: port 2(wlan0) entered forwarding state 702 -[ 2245.748473] device wlan0 left promiscuous mode 703 -[ 2245.753145] br-lan: port 2(wlan0) entered disabled state 704 -[ 2246.536062] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready 705 -[ 2246.546273] br-lan: port 2(wlan0) entered blocking state 706 -[ 2246.551680] br-lan: port 2(wlan0) entered disabled state 707 -[ 2246.557667] device wlan0 entered promiscuous mode 708 -[ 2246.562855] br-lan: port 2(wlan0) entered blocking state 709 -[ 2246.568267] br-lan: port 2(wlan0) entered forwarding state 710 -[ 2246.838430] br-lan: port 2(wlan0) entered disabled state 711 -[ 2246.948147] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready 712 -[ 2246.954850] br-lan: port 2(wlan1) entered blocking state 713 -[ 2246.960197] br-lan: port 2(wlan1) entered forwarding state 714 - 715 -root@OpenWrt:/etc# 716 -root@OpenWrt:/etc# uci show wireless 717 -wireless.radio0=wifi-device 718 -wireless.radio0.type='mac80211' 719 -wireless.radio0.channel='11' 720 -wireless.radio0.hwmode='11g' 721 -wireless.radio0.path='pci0000:00/0000:00:00.0/0000:01:00.0' 722 -wireless.radio0.country='00' 723 -wireless.radio0.legacy_rates='1' 724 -wireless.radio0.htmode='HT20' 725 -wireless.default_radio0=wifi-iface 726 -wireless.default_radio0.device='radio0' 727 -wireless.default_radio0.network='lan' 728 -wireless.default_radio0.mode='ap' 729 -wireless.default_radio0.encryption='psk2' 730 -wireless.default_radio0.key='qwerty1234' 731 -wireless.default_radio0.ssid='asdf' 732 -wireless.radio1=wifi-device 733 -wireless.radio1.type='mac80211' 734 -wireless.radio1.channel='36' 735 -wireless.radio1.hwmode='11a' 736 -wireless.radio1.path='pci0000:00/0000:00:01.0/0000:02:00.0' 737 -wireless.radio1.htmode='VHT80' 738 -wireless.radio1.__toggle='Enable' 739 -wireless.radio1.country='00' 740 -wireless.radio1.legacy_rates='1' 741 -wireless.default_radio1=wifi-iface 742 -wireless.default_radio1.device='radio1' 743 -wireless.default_radio1.network='lan' 744 -wireless.default_radio1.mode='ap' 745 -wireless.default_radio1.ssid='asdf' 746 -wireless.default_radio1.encryption='psk2' 747 -wireless.default_radio1.key='qwerty1234' 748 -root@OpenWrt:/etc# 749 749 {{/code}} 750 - 751 -Firmware: 752 - 753 -./staging_dir/target-mipsel_24kc_glibc/root-ramips/lib/firmware/mediatek/mt7615_rom_patch.bin
- 1567332570723-651.png
-
- Author
-
... ... @@ -1,1 +1,0 @@ 1 -XWiki.CodePowered - Size
-
... ... @@ -1,1 +1,0 @@ 1 -166.8 KB - Content
- openwrt-ramips-mt7621-linksys_ea8100-initramfs-kernel-9bebafcb5dfe37f25285fa18fb8bfe7b68011267.bin
-
- Author
-
... ... @@ -1,1 +1,0 @@ 1 -XWiki.CodePowered - Size
-
... ... @@ -1,1 +1,0 @@ 1 -4.5 MB - Content
- openwrt-ramips-mt7621-linksys_ea8100-squashfs-sysupgrade-9bebafcb5dfe37f25285fa18fb8bfe7b68011267.bin
-
- Author
-
... ... @@ -1,1 +1,0 @@ 1 -XWiki.CodePowered - Size
-
... ... @@ -1,1 +1,0 @@ 1 -5.6 MB - Content