Last modified by Leon Poon on 2021/07/16 18:40
From version 2.1
edited by Leon Poon
on 2019/02/16 05:55
Change comment: There is no comment for this version
To version 57.1
edited by Leon Poon
on 2021/07/16 10:40
Change comment: There is no comment for this version

Summary

Details

Page properties
Parent
... ... @@ -1,1 +1,1 @@
1 -Main.Linksys EA8100.WebHome
1 +Linksys EA8100.WebHome
Content
... ... @@ -1,37 +1,194 @@
1 1  switch0: port 0 = wan, port 1,2,3,4 = lan
2 2  
3 +If you brick your router you should be able to recover by soldering the UART pin headers and connecting to the serial. See [[this page for pictures>>doc:Linksys EA8100.WebHome]].
3 3  
4 -[[https:~~/~~/github.com/LeonPoon/openwrt/compare/master...master-linksys_ea8100>>https://github.com/LeonPoon/openwrt/compare/master...master-linksys_ea8100]]
5 += 21.02.x =
5 5  
6 -b90086cc98a15a2774382b691f1249f4ad11a1c7:
7 +Thanks to [[this patch>>https://github.com/openwrt/openwrt/commit/97df795b78dc572ea2ec105ccbf8af27cc4b4d8e]], EA8100 is now supported from openwrt 21.02.
7 7  
8 -<code>
9 +The 21.02 release is currently at RC3. You can get it from [[openwrt firmware selector>>https://firmware-selector.openwrt.org/?version=21.02.0-rc3&target=ramips%2Fmt7621&id=linksys_ea8100-v1]] page.
9 9  
10 -check env def auto_recovery no
11 -check env def auto_recovery yes
12 -check env def boot_part 1
13 -check env def boot_part_ready 3
14 -enabled:1, boot_part:2, boot_part_ready:3
15 -..nand read ret = 0x20000
16 -boot_count:1, next_record:4
17 -boot_count:1, next_record:4
11 +Both 2.4Ghz and 5Ghz wifi are working fine.
18 18  
19 -3: System Boot system code via Flash.
20 -~#~# Booting image at be980000 ...
21 - Image Name: MIPS OpenWrt Linux-4.14.101
13 +If you are already on 19.07, please do not sysupgrade with 21.02 sysupgrade.bin, because sysupgrade.bin format in 21.02 is not supported by 19.07 sysupgrade utility.
14 +
15 +21.02 images:
16 +
17 +{{code language="none"}}
18 +openwrt-21.02.0-rc3-ramips-mt7621-linksys_ea8100-v1-initramfs-kernel.bin: u-boot legacy uImage, MIPS OpenWrt Linux-5.4.124, Linux/MIPS, OS Kernel Image (Not compressed), 4912189 bytes, Sun Jun 13 22:02:19 2021, Load Address: 0x80001000, Entry Point: 0x80001000, Header CRC: 0x9C4276B9, Data CRC: 0xBC5373AC
19 +openwrt-21.02.0-rc3-ramips-mt7621-linksys_ea8100-v1-squashfs-factory.bin: u-boot legacy uImage, MIPS OpenWrt Linux-5.4.124, Linux/MIPS, OS Kernel Image (Not compressed), 2357363 bytes, Sun Jun 13 22:02:19 2021, Load Address: 0x80001000, Entry Point: 0x80001000, Header CRC: 0xAC8B8E31, Data CRC: 0xC42A191A
20 +openwrt-21.02.0-rc3-ramips-mt7621-linksys_ea8100-v1-squashfs-sysupgrade.bin: POSIX tar archive (GNU)
21 +{{/code}}
22 +
23 +(% class="wikigeneratedid" %)
24 +19.07:
25 +
26 +{{code language="none"}}
27 +openwrt-ramips-mt7621-ea8100-initramfs-factory.img: u-boot legacy uImage, MIPS OpenWrt Linux-4.14.221, Linux/MIPS, OS Kernel Image (lzma), 5049994 bytes, Mon Feb 15 15:22:37 2021, Load Address: 0x80001000, Entry Point: 0x80001000, Header CRC: 0x9EAE22DC, Data CRC: 0x739C919A
28 +openwrt-ramips-mt7621-ea8100-initramfs-kernel.bin: u-boot legacy uImage, MIPS OpenWrt Linux-4.14.221, Linux/MIPS, OS Kernel Image (lzma), 5049994 bytes, Mon Feb 15 15:22:37 2021, Load Address: 0x80001000, Entry Point: 0x80001000, Header CRC: 0x9EAE22DC, Data CRC: 0x739C919A
29 +openwrt-ramips-mt7621-ea8100-squashfs-factory.img: u-boot legacy uImage, MIPS OpenWrt Linux-4.14.221, Linux/MIPS, OS Kernel Image (lzma), 2012291 bytes, Mon Feb 15 15:22:37 2021, Load Address: 0x80001000, Entry Point: 0x80001000, Header CRC: 0xD210527A, Data CRC: 0x404E16F6
30 +openwrt-ramips-mt7621-ea8100-squashfs-sysupgrade.bin: u-boot legacy uImage, MIPS OpenWrt Linux-4.14.221, Linux/MIPS, OS Kernel Image (lzma), 2012291 bytes, Mon Feb 15 15:22:37 2021, Load Address: 0x80001000, Entry Point: 0x80001000, Header CRC: 0xD210527A, Data CRC: 0x404E16F6
31 +{{/code}}
32 +
33 +
34 +
35 +Flashing 21.02 squashfs-sysupgrade.bin using sysupgrade in 19.07 will soft brick your router. (Sysupgrade will likely reject the image anyway, and you will have to use force flag if you really want to do it.)
36 +
37 +If you insist, force flashing the 21.02 squashfs-factory.bin should allow you to succeed in the upgrade. (Not tested.)
38 +
39 += 19.07.x =
40 +
41 +Openwrt 19.07.7 for EA8100 is here!
42 +
43 +Since [[19.07.03>>https://www.codepowered.com/openwrt/v19.07.3/linksys_ea8100/]], as of 19.07.07:
44 +
45 +* Wifi (5Ghz) seem to work at 30-40MB/s with a MacBook Pro.
46 +* **Known issue**: 2.4Ghz wifi performance is really bad. You probably want to disable 2.4Ghz wifi.
47 +
48 +UPDATED 2020-12-10 the 19.07.04 and later builds now includes LuCi!
49 +
50 +(% class="box warningmessage" %)
51 +(((
52 +Always use a PC connected to the device via wired ethernet for flashing firmwares.
53 +)))
54 +
55 +Follow these instructions:
56 +
57 +1. Download ##[[initramfs-factory.img>>https://www.codepowered.com/openwrt/v19.07.7/bin/targets/ramips/mt7621/openwrt-ramips-mt7621-ea8100-initramfs-factory.img]]## and ##[[squashfs-sysupgrade.bin>>https://www.codepowered.com/openwrt/v19.07.7/bin/targets/ramips/mt7621/openwrt-ramips-mt7621-ea8100-squashfs-sysupgrade.bin||style="background-color: rgb(255, 255, 255);"]]##
58 +1. Access Linksys UI (default [[http:~~/~~/192.168.10.1/>>http://192.168.10.1/]]). Flash **##initramfs-factory.img##**. It will reboot.
59 +1. Wait for Openwrt to boot so that you get to LuCi at [[http:~~/~~/192.168.1.1/>>http://192.168.1.1/]]. You might need to restart your PC so that it gets a ##192.168.1.x## address from openwrt. Once you get LuCI, do NOT configure yet! It's not ready.
60 +1. Flash **##squashfs-sysupgrade.bin##** via LuCi
61 +1. Wait for it to reboot. Now you can configure!
62 +
63 +For kernel modules, replace the relevant link in your ##/etc/opkg/distfeeds.conf(% class="small" %) (%%)##with this:
64 +
65 +{{code language="none"}}
66 +src/gz openwrt_core https://www.codepowered.com/openwrt/v19.07.7/bin/targets/ramips/mt7621/packages
67 +{{/code}}
68 +
69 +If you are on my 18.x below, sysupgrading to a 19.07 image will not work. You have to manually mtd write the 19.07 "kernel-initramfs.bin" into the nand and boot/log into it (192.168.1.1), then sysupgrade.
70 +
71 +Sysupgrade from 19.07.x to another 19.07.y will work. You can also upgrade via LuCI.
72 +
73 +{{warning}}
74 +Upgrading images will wipe entire firmware partitions! Backup your files/config before sysupgrade. It will reset router ip to 192.168.1.1.
75 +{{/warning}}
76 +
77 +--**Images do not contain LuCi! (The build process doesn't include it for some reason I have not yet time to figure out.)** You need to have the **squashfs-sysupgrade.bin** flashed, then install LuCI. (See instructions below.)--
78 +
79 +--The EA8100 contains 2 firmware partitions. Using the Linksys UI will flash openwrt into only one of the 2 partitions. The booting process switches partition every few boots, so if you want to always boot into openwrt then you have to flash openwrt into both partitions.--
80 +
81 +--How to flash if your router currently has stock Linksys firmware:--
82 +
83 +1. --Download the "**openwrt-ramips-mt7621-ea8100-initramfs-kernel-factory.img**" from link above, and flash it via Linksys UI. Wait for it to start to reboot.--
84 +1. --Configure your computer to have IP in ##192.168.1.2/255.255.255.0##.--
85 +1. --Check that your router booted Openwrt by visiting [[http:~~/~~/192.168.1.1/>>http://192.168.1.1/]]. It is in Openwrt if you see a white screen with message: "Index of /." Do a reboot if you see Linksys UI instead, then check again when it boots. --
86 +1. --Download the "**openwrt-ramips-mt7621-ea8100-squashfs-sysupgrade.bin**" from link above, and upload it into ##/tmp## in the router via SFTP. You can use [[winscp>>doc:How to WinSCP.WebHome]] if on Windows. [[root@192.168.1.1>>mailto:root@192.168.1.1]] (No password).--
87 +1. --Ssh into [[root@192.168.1.1>>mailto:root@192.168.1.1]] (no password). Use [[putty>>doc:How to Putty.WebHome]] to ssh if you are on Windows.--
88 +1. --In the ssh shell run: ##sysupgrade /tmp/openwrt-ramips-mt7621-ea8100-squashfs-sysupgrade.bin##--
89 +1. --It automatically reboots after a short while. Log in via SSH again. Check you are online by pinging 8.8.8.8 when in SSH.--
90 +1. --Run: ##opkg update##--
91 +1. --Run: ##**opkg install luci**##--
92 +1. --Access LuCI via [[http:~~/~~/192.168.1.1/>>http://192.168.1.1/]]. You can now configure.--
93 +
94 += 18.x =
95 +
96 +9bebafcb5dfe37f25285fa18fb8bfe7b68011267 (with wifi support) Download:
97 +
98 +* [[initramfs-kernel.bin>>attach:openwrt-ramips-mt7621-linksys_ea8100-initramfs-kernel-9bebafcb5dfe37f25285fa18fb8bfe7b68011267.bin]]
99 +* [[squashfs-sysupgrade.bin>>attach:openwrt-ramips-mt7621-linksys_ea8100-squashfs-sysupgrade-9bebafcb5dfe37f25285fa18fb8bfe7b68011267.bin]] (accepted as upgrade in factory UI)
100 +
101 +Note that sysupgrade to a newer image is not likely to work.
102 +
103 +(% border="1" cellpadding="0" cellspacing="0" style="margin-right:auto; width:auto" %)
104 +|[[image:1567332570723-651.png]]
105 +
106 +Dmesg:
107 +
108 +{{code language="plain"}}
109 + 3: Boot system code via Flash (default).
110 + 4: Entr boot command line interface.
111 + 7: Load Boot Loader code then write to Flash via Serial.
112 + 9: Load Boot Loader code then write to Flash via TFTP. 4
113 +You choosed 2
114 + 0
115 +
116 +
117 +2: System Load Linux Kernel then write to Flash via TFTP.
118 + Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N)
119 + Please Input new ones /or Ctrl-C to discard
120 + Input device IP () ==:
121 + Input server IP () ==:
122 + Input Linux Kernel filename (openwrt-ramips-mt7621-linksys_ea8100-initramfs-kernel.bin) ==:openwrt-ramips-mt7621-linksys_ea8100-squashfs-sysupgrade.bin
123 + which kernel partition to update (1/2/3=both) (2) ==:3
124 +
125 + NetTxPacket = 0x8FFE3200
126 +
127 + KSEG1ADDR(NetTxPacket) = 0xAFFE3200
128 +
129 + NetLoop,call eth_halt !
130 +
131 + NetLoop,call eth_init !
132 +Trying Eth0 (10/100-M)
133 +
134 + Waitting for RX_DMA_BUSY status Start... done
135 +
136 +
137 + ETH_STATE_ACTIVE!!
138 +TFTP from server ; our IP address is
139 +Filename 'openwrt-ramips-mt7621-linksys_ea8100-squashfs-sysupgrade.bin'.
140 +
141 + TIMEOUT_COUNT=10,Load address: 0x80100000
142 +Loading: Got ARP REPLY, set server/gtwy eth addr ()
143 +Got it
144 +#################################################################
145 + #################################################################
146 + #################################################################
147 + #################################################################
148 + #################################################################
149 + #################################################################
150 + #################################################################
151 + #################################################################
152 + #################################################################
153 + #################################################################
154 + #################################################################
155 + #################################################################
156 + #################################################################
157 + #################################################################
158 + #################################################################
159 + #################################################################
160 + #################################################################
161 + ################################################
162 +done
163 +Bytes transferred = 5898496 (5a0100 hex)
164 +LoadAddr=80100000 NetBootFileXferSize= 005a0100
165 +ranand_erase: start:180000, len:20000
166 +..ranand_erase: start:1a0000, len:20000
167 +..ranand_erase: start:1c0000, len:20000
168 +...
169 +.(5192)offs=7471104 piece=0 piece_size=256 rc=0
170 +Done!
171 +ranand_erase: start:2980000, len:20000
172 +..ranand_erase: start:29a0000, len:20000
173 +..ranand_erase: start:29c0000, len:20000
174 +...
175 +.(5192)offs=49676288 piece=0 piece_size=256 rc=0
176 +Done!
177 +## Booting image at bc180000 ...
178 + Image Name: MIPS OpenWrt Linux-4.14.141
22 22   Image Type: MIPS Linux Kernel Image (lzma compressed)
23 - Data Size: 1908285 Bytes = 1.8 MB
180 + Data Size: 2010110 Bytes = 1.9 MB
24 24   Load Address: 80001000
25 25   Entry Point: 80001000
26 -.............................. Verifying Checksum ... OK
183 +............................... Verifying Checksum ... OK
27 27   Uncompressing Kernel Image ... OK
28 28  No initrd
29 -~#~# Transferring control to Linux (at address 80001000) ...
30 -~#~# Giving linux memsize in MB, 256
186 +## Transferring control to Linux (at address 80001000) ...
187 +## Giving linux memsize in MB, 256
31 31  
32 32  Starting kernel ...
33 33  
34 -[ 0.000000] Linux version 4.14.101 () (gcc version 7.4.0 (OpenWrt GCC 7.4.0 r9033-cbee2131d6)) #0 SMP Sat Feb 16 05:28:27 2019
191 +[ 0.000000] Linux version 4.14.141 () (gcc version 7.4.0 (OpenWrt GCC 7.4.0 r10942-9bebafcb5d)) #0 SMP Sun Sep 1 06:04:50 2019
35 35  [ 0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3
36 36  [ 0.000000] bootconsole [early0] enabled
37 37  [ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
... ... @@ -50,16 +50,16 @@
50 50  [ 0.000000] Early memory node ranges
51 51  [ 0.000000] node 0: [mem 0x0000000000000000-0x000000000fffffff]
52 52  [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff]
53 -[ 0.000000] random: get_random_bytes called from start_kernel+0x90/0x4a4 with crng_init=0
54 -[ 0.000000] percpu: Embedded 14 pages/cpu @8120f000 s26192 r8192 d22960 u57344
55 -[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 65024
210 +[ 0.000000] random: get_random_bytes called from start_kernel+0x9c/0x4d8 with crng_init=0
211 +[ 0.000000] percpu: Embedded 14 pages/cpu s26064 r8192 d23088 u57344
212 +[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 64960
56 56  [ 0.000000] Kernel command line: console=ttyS0,115200n8 rootfstype=squashfs,jffs2
57 57  [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
58 58  [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
59 59  [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
60 -[ 0.000000] Writing ErrCtl register=0002c42c
61 -[ 0.000000] Readback ErrCtl register=0002c42c
62 -[ 0.000000] Memory: 253304K/262144K available (4502K kernel code, 233K rwdata, 1000K rodata, 268K init, 248K bss, 8840K reserved, 0K cma-reserved, 0K highmem)
217 +[ 0.000000] Writing ErrCtl register=0002c420
218 +[ 0.000000] Readback ErrCtl register=0002c420
219 +[ 0.000000] Memory: 251700K/262144K available (4796K kernel code, 251K rwdata, 1040K rodata, 1260K init, 254K bss, 10444K reserved, 0K cma-reserved, 0K highmem)
63 63  [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
64 64  [ 0.000000] Hierarchical RCU implementation.
65 65  [ 0.000000] NR_IRQS: 256
... ... @@ -67,231 +67,595 @@
67 67  [ 0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns
68 68  [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4343773742 ns
69 69  [ 0.000009] sched_clock: 32 bits at 440MHz, resolution 2ns, wraps every 4880645118ns
70 -[ 0.007805] Calibrating delay loop... 586.13 BogoMIPS (lpj=2930688)
71 -[ 0.073978] pid_max: default: 32768 minimum: 301
72 -[ 0.078744] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
73 -[ 0.085252] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
74 -[ 0.094034] Hierarchical SRCU implementation.
75 -[ 0.099185] smp: Bringing up secondary CPUs ...
76 -[ 0.109505] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
77 -[ 0.109515] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
78 -[ 0.109526] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
79 -[ 0.109664] CPU1 revision is: 0001992f (MIPS 1004Kc)
80 -[ 0.163934] Synchronize counters for CPU 1: done.
81 -[ 0.203356] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
82 -[ 0.203365] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
83 -[ 0.203372] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
84 -[ 0.203446] CPU2 revision is: 0001992f (MIPS 1004Kc)
85 -[ 0.255085] Synchronize counters for CPU 2: done.
86 -[ 0.290669] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
87 -[ 0.290678] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
88 -[ 0.290686] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
89 -[ 0.290767] CPU3 revision is: 0001992f (MIPS 1004Kc)
90 -[ 0.340270] Synchronize counters for CPU 3: done.
91 -[ 0.370137] smp: Brought up 1 node, 4 CPUs
92 -[ 0.377732] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
93 -[ 0.387523] futex hash table entries: 1024 (order: 3, 32768 bytes)
94 -[ 0.393811] pinctrl core: initialized pinctrl subsystem
95 -[ 0.400270] NET: Registered protocol family 16
96 -[ 0.423063] mt7621_gpio 1e000600.gpio: registering 32 gpios
97 -[ 0.428878] mt7621_gpio 1e000600.gpio: registering 32 gpios
98 -[ 0.434658] mt7621_gpio 1e000600.gpio: registering 32 gpios
99 -[ 0.442956] clocksource: Switched to clocksource GIC
100 -[ 0.449425] NET: Registered protocol family 2
101 -[ 0.454419] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
102 -[ 0.461303] TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
103 -[ 0.467778] TCP: Hash tables configured (established 2048 bind 2048)
104 -[ 0.474212] UDP hash table entries: 256 (order: 1, 8192 bytes)
105 -[ 0.479979] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
106 -[ 0.486452] NET: Registered protocol family 1
107 -[ 0.722896] 4 CPUs re-calibrate udelay(lpj = 2924544)
108 -[ 0.729302] Crashlog allocated RAM at address 0x3f00000
109 -[ 0.734701] workingset: timestamp_bits=30 max_order=16 bucket_order=0
110 -[ 0.748195] squashfs: version 4.0 (2009/01/31) Phillip Lougher
111 -[ 0.753975] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
112 -[ 0.765554] random: fast init done
113 -[ 0.770526] io scheduler noop registered
114 -[ 0.774396] io scheduler deadline registered (default)
115 -[ 0.780409] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled
116 -[ 0.788106] console [ttyS0] disabled
117 -[ 0.791645] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 18, base_baud = 3125000) is a 16550A
118 -[ 0.800653] console [ttyS0] enabled
119 -[ 0.800653] console [ttyS0] enabled
120 -[ 0.807523] bootconsole [early0] disabled
121 -[ 0.807523] bootconsole [early0] disabled
122 -[ 0.816146] cacheinfo: Unable to detect cache hierarchy for CPU 0
123 -[ 0.823038] MediaTek Nand driver init, version v2.1 Fix AHB virt2phys error
124 -[ 0.830119] Enable NFI Clock
125 -[ 0.833044] # MTK NAND # : Use HW ECC
126 -[ 0.836708] Device not found, ID: c2f1
127 -[ 0.840433] Not Support this Device!
128 -[ 0.844177] chip_mode=00000001
129 -[ 0.847217] Support this Device in MTK table! c2f1
130 -[ 0.852163] [NAND]select ecc bit:4, sparesize :64 spare_per_sector=16
131 -[ 0.858632] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xf1
132 -[ 0.864966] nand: Macronix NAND 128MiB 3,3V 8-bit
133 -[ 0.869648] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
134 -[ 0.877212] Scanning device for bad blocks
135 -[ 0.898080] Bad eraseblock 71 at 0x0000008e0000
136 -[ 0.967695] Bad eraseblock 349 at 0x000002ba0000
137 -[ 0.978049] Bad eraseblock 374 at 0x000002ec0000
138 -[ 0.987933] Bad eraseblock 397 at 0x0000031a0000
139 -[ 1.006268] Bad eraseblock 456 at 0x000003900000
140 -[ 1.021533] Bad eraseblock 502 at 0x000003ec0000
141 -[ 1.034940] Bad eraseblock 540 at 0x000004380000
142 -[ 1.050681] Bad eraseblock 588 at 0x000004980000
143 -[ 1.107262] Bad eraseblock 810 at 0x000006540000
144 -[ 1.129339] Bad eraseblock 885 at 0x000006ea0000
145 -[ 1.166421] 7 fixed-partitions partitions found on MTD device MT7621-NAND
146 -[ 1.173195] Creating 7 MTD partitions on "MT7621-NAND":
147 -[ 1.178405] 0x000000000000-0x000000080000 : "uboot"
148 -[ 1.184240] 0x000000080000-0x0000000c0000 : "uboot_env"
149 -[ 1.190298] 0x0000000c0000-0x000000100000 : "factory"
150 -[ 1.196219] 0x000000100000-0x000000140000 : "s_env"
151 -[ 1.201900] 0x000000140000-0x000000180000 : "devinfo"
152 -[ 1.207850] 0x000000180000-0x000002980000 : "firmware1"
153 -[ 1.216116] 0x000002980000-0x000005180000 : "firmware2"
154 -[ 1.223224] 1 uboot-env-boot_part partitions found on MTD device firmware2
155 -[ 1.230090] 0x000002980000-0x000005180000 : "firmware"
156 -[ 1.784436] 2 uimage-fw partitions found on MTD device firmware
157 -[ 1.790355] 0x000002980000-0x000002b60000 : "kernel"
158 -[ 1.796251] 0x000002b60000-0x000005180000 : "ubi"
159 -[ 1.802130] [mtk_nand] probe successfully!
160 -[ 1.806957] Signature matched and data read!
161 -[ 1.811205] load_fact_bbt success 1023
162 -[ 1.815701] libphy: Fixed MDIO Bus: probed
163 -[ 1.885315] mtd_read_prop_mac: find prop "hw_mac_addr" in devinfo(max 0x40000) from 0x0
164 -[ 1.893332] mtd_read_prop_mac: hw_mac_addr=XX:YY:ZZ:00:11:33
165 -[ 1.899142] libphy: mdio: probed
166 -[ 3.302014] mtk_soc_eth 1e100000.ethernet: loaded mt7530 driver
167 -[ 3.308669] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 20
168 -[ 3.319426] NET: Registered protocol family 10
169 -[ 3.325219] Segment Routing with IPv6
170 -[ 3.328949] NET: Registered protocol family 17
171 -[ 3.333457] 8021q: 802.1Q VLAN Support v1.8
172 -[ 3.340506] UBI: auto-attach mtd9
173 -[ 3.343893] ubi0: attaching mtd9
174 -[ 3.363286] UBI: EOF marker found, PEBs from 15 will be erased
175 -[ 3.369474] ubi0: scanning is finished
176 -[ 3.411360] ubi0: volume 1 ("rootfs_data") re-sized from 9 to 269 LEBs
177 -[ 3.418731] ubi0: attached mtd9 (name "ubi", size 38 MiB)
178 -[ 3.424164] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
179 -[ 3.431006] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
180 -[ 3.437780] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
181 -[ 3.444725] ubi0: good PEBs: 298, bad PEBs: 7, corrupted PEBs: 0
182 -[ 3.450701] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
183 -[ 3.457906] ubi0: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 1203044710
184 -[ 3.467015] ubi0: available PEBs: 0, total reserved PEBs: 298, PEBs reserved for bad PEB handling: 13
185 -[ 3.476230] ubi0: background thread "ubi_bgt0d" started, PID 359
186 -[ 3.477972] block ubiblock0_0: created from ubi0:0(rootfs)
187 -[ 3.487716] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem
188 -[ 3.494673] hctosys: unable to open rtc device (rtc0)
189 -[ 3.519930] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
190 -[ 3.527684] Freeing unused kernel memory: 268K
191 -[ 3.532122] This architecture does not have kernel memory protection.
192 -[ 4.017012] init: Console is alive
193 -[ 4.020616] init: - watchdog -
194 -[ 4.354210] kmodloader: loading kernel modules from /etc/modules-boot.d/*
195 -[ 4.443714] usbcore: registered new interface driver usbfs
196 -[ 4.449260] usbcore: registered new interface driver hub
197 -[ 4.454739] usbcore: registered new device driver usb
198 -[ 4.467426] SCSI subsystem initialized
199 -[ 4.480878] xhci-mtk 1e1c0000.xhci: 1e1c0000.xhci supply vbus not found, using dummy regulator
200 -[ 4.489588] xhci-mtk 1e1c0000.xhci: 1e1c0000.xhci supply vusb33 not found, using dummy regulator
201 -[ 4.498507] xhci-mtk 1e1c0000.xhci: xHCI Host Controller
202 -[ 4.503843] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 1
203 -[ 4.523114] xhci-mtk 1e1c0000.xhci: hcc params 0x01401198 hci version 0x96 quirks 0x0000000000210010
204 -[ 4.532283] xhci-mtk 1e1c0000.xhci: irq 19, io mem 0x1e1c0000
205 -[ 4.538971] hub 1-0:1.0: USB hub found
206 -[ 4.542796] hub 1-0:1.0: 2 ports detected
207 -[ 4.547400] xhci-mtk 1e1c0000.xhci: xHCI Host Controller
208 -[ 4.552722] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 2
209 -[ 4.560210] xhci-mtk 1e1c0000.xhci: Host supports USB 3.0 SuperSpeed
210 -[ 4.560493] mtk_soc_eth 1e100000.ethernet eth0: port 4 link up
211 -[ 4.566816] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
212 -[ 4.581320] hub 2-0:1.0: USB hub found
213 -[ 4.585161] hub 2-0:1.0: 1 port detected
214 -[ 4.593449] usbcore: registered new interface driver usb-storage
215 -[ 4.599693] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
216 -[ 4.623240] init: - preinit -
217 -[ 5.073028] usb 1-2: new high-speed USB device number 2 using xhci-mtk
218 -[ 5.221107] mtk_soc_eth 1e100000.ethernet: PPE started
219 -[ 5.255985] usb-storage 1-2:1.0: USB Mass Storage device detected
220 -[ 5.262845] scsi host0: usb-storage 1-2:1.0
227 +[ 0.007802] Calibrating delay loop... 586.13 BogoMIPS (lpj=2930688)
228 +[ 0.073969] pid_max: default: 32768 minimum: 301
229 +[ 0.078775] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
230 +[ 0.085284] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
231 +[ 0.094340] Hierarchical SRCU implementation.
232 +[ 0.099495] smp: Bringing up secondary CPUs ...
233 +[ 0.114811] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
234 +[ 0.114820] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
235 +[ 0.114831] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
236 +[ 0.114963] CPU1 revision is: 0001992f (MIPS 1004Kc)
237 +[ 0.164211] Synchronize counters for CPU 1: done.
238 +[ 0.208189] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
239 +[ 0.208197] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
240 +[ 0.208206] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
241 +[ 0.208284] CPU2 revision is: 0001992f (MIPS 1004Kc)
242 +[ 0.255179] Synchronize counters for CPU 2: done.
243 +[ 0.295789] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
244 +[ 0.295797] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
245 +[ 0.295805] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
246 +[ 0.295885] CPU3 revision is: 0001992f (MIPS 1004Kc)
247 +[ 0.340367] Synchronize counters for CPU 3: done.
248 +[ 0.370232] smp: Brought up 1 node, 4 CPUs
249 +[ 0.378204] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
250 +[ 0.388001] futex hash table entries: 1024 (order: 3, 32768 bytes)
251 +[ 0.394408] pinctrl core: initialized pinctrl subsystem
252 +[ 0.401009] NET: Registered protocol family 16
253 +[ 0.415266] pull PCIe RST: RALINK_RSTCTRL = 4000000
254 +[ 0.720548] release PCIe RST: RALINK_RSTCTRL = 7000000
255 +[ 0.725598] ***** Xtal 40MHz *****
256 +[ 0.728952] release PCIe RST: RALINK_RSTCTRL = 7000000
257 +[ 0.734049] Port 0 N_FTS = 1b102800
258 +[ 0.737517] Port 1 N_FTS = 1b102800
259 +[ 0.740963] Port 2 N_FTS = 1b102800
260 +[ 1.896358] PCIE2 no card, disable it(RST&CLK)
261 +[ 1.900719] -> 21007f2
262 +[ 1.903123] PCIE0 enabled
263 +[ 1.905712] PCIE1 enabled
264 +[ 1.908316] PCI host bridge /pcie@1e140000 ranges:
265 +[ 1.913096] MEM 0x0000000060000000..0x000000006fffffff
266 +[ 1.918245] IO 0x000000001e160000..0x000000001e16ffff
267 +[ 1.923451] PCI coherence region base: 0xbfbf8000, mask/settings: 0x60000000
268 +[ 1.939415] mt7621_gpio 1e000600.gpio: registering 32 gpios
269 +[ 1.945254] mt7621_gpio 1e000600.gpio: registering 32 gpios
270 +[ 1.950961] mt7621_gpio 1e000600.gpio: registering 32 gpios
271 +[ 1.958178] PCI host bridge to bus 0000:00
272 +[ 1.962213] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
273 +[ 1.969068] pci_bus 0000:00: root bus resource [io 0xffffffff]
274 +[ 1.974896] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
275 +[ 1.981655] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
276 +[ 1.990318] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
277 +[ 1.998262] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
278 +[ 2.007510] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
279 +[ 2.014070] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
280 +[ 2.020937] pci 0000:00:01.0: BAR 0: no space for [mem size 0x80000000]
281 +[ 2.027521] pci 0000:00:01.0: BAR 0: failed to assign [mem size 0x80000000]
282 +[ 2.034415] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
283 +[ 2.041173] pci 0000:00:01.0: BAR 8: assigned [mem 0x60100000-0x601fffff]
284 +[ 2.047897] pci 0000:00:00.0: BAR 1: assigned [mem 0x60200000-0x6020ffff]
285 +[ 2.054657] pci 0000:00:01.0: BAR 1: assigned [mem 0x60210000-0x6021ffff]
286 +[ 2.061377] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit]
287 +[ 2.068661] pci 0000:00:00.0: PCI bridge to [bus 01]
288 +[ 2.073551] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff]
289 +[ 2.080327] pci 0000:02:00.0: BAR 0: assigned [mem 0x60100000-0x601fffff 64bit]
290 +[ 2.087559] pci 0000:00:01.0: PCI bridge to [bus 02]
291 +[ 2.092502] pci 0000:00:01.0: bridge window [mem 0x60100000-0x601fffff]
292 +[ 2.100582] clocksource: Switched to clocksource GIC
293 +[ 2.107275] NET: Registered protocol family 2
294 +[ 2.112196] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
295 +[ 2.119081] TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
296 +[ 2.125539] TCP: Hash tables configured (established 2048 bind 2048)
297 +[ 2.131955] UDP hash table entries: 256 (order: 1, 8192 bytes)
298 +[ 2.137713] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
299 +[ 2.144212] NET: Registered protocol family 1
300 +[ 2.380532] 4 CPUs re-calibrate udelay(lpj = 2924544)
301 +[ 2.387039] Crashlog allocated RAM at address 0x3f00000
302 +[ 2.392460] workingset: timestamp_bits=14 max_order=16 bucket_order=2
303 +[ 2.408000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
304 +[ 2.413806] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
305 +[ 2.425815] random: fast init done
306 +[ 2.430745] io scheduler noop registered
307 +[ 2.434579] io scheduler deadline registered (default)
308 +[ 2.440747] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled
309 +[ 2.448257] console [ttyS0] disabled
310 +[ 2.451855] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 19, base_baud = 3125000) is a 16550A
311 +[ 2.460836] console [ttyS0] enabled
312 +[ 2.460836] console [ttyS0] enabled
313 +[ 2.467691] bootconsole [early0] disabled
314 +[ 2.467691] bootconsole [early0] disabled
315 +[ 2.477567] MediaTek Nand driver init, version v2.1 Fix AHB virt2phys error
316 +[ 2.484816] Enable NFI Clock
317 +[ 2.487689] # MTK NAND # : Use HW ECC
318 +[ 2.491382] Device not found, ID: c2f1
319 +[ 2.495110] Not Support this Device!
320 +[ 2.498835] chip_mode=00000001
321 +[ 2.501893] Support this Device in MTK table! c2f1
322 +[ 2.506840] [NAND]select ecc bit:4, sparesize :64 spare_per_sector=16
323 +[ 2.513320] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xf1
324 +[ 2.519642] nand: Macronix NAND 128MiB 3,3V 8-bit
325 +[ 2.524347] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
326 +[ 2.531927] Scanning device for bad blocks
327 +[ 2.819771] 7 fixed-partitions partitions found on MTD device MT7621-NAND
328 +[ 2.826546] Creating 7 MTD partitions on "MT7621-NAND":
329 +[ 2.831774] 0x000000000000-0x000000080000 : "uboot"
330 +[ 2.837706] 0x000000080000-0x0000000c0000 : "uboot_env"
331 +[ 2.843891] 0x0000000c0000-0x000000100000 : "factory"
332 +[ 2.849892] 0x000000100000-0x000000140000 : "s_env"
333 +[ 2.855720] 0x000000140000-0x000000180000 : "devinfo"
334 +[ 2.861732] 0x000000180000-0x000002980000 : "firmware1"
335 +[ 2.870032] 0x000002980000-0x000005180000 : "firmware2"
336 +[ 2.877154] 1 uboot-env-boot_part partitions found on MTD device firmware2
337 +[ 2.884061] 0x000002980000-0x000005180000 : "firmware"
338 +[ 3.438509] 2 uimage-fw partitions found on MTD device firmware
339 +[ 3.444473] 0x000002980000-0x000002b80000 : "kernel"
340 +[ 3.450603] 0x000002b80000-0x000005180000 : "ubi"
341 +[ 3.456742] [mtk_nand] probe successfully!
342 +[ 3.461570] Signature matched and data read!
343 +[ 3.465818] load_fact_bbt success 1023
344 +[ 3.470276] libphy: Fixed MDIO Bus: probed
345 +[ 3.542951] mtd_read_prop_mac: find prop "hw_mac_addr" in devinfo(max 0x40000) from 0x0
346 +[ 3.550970] mtd_read_prop_mac: hw_mac_addr=
347 +[ 3.556774] libphy: mdio: probed
348 +[ 4.961009] mtk_soc_eth 1e100000.ethernet: loaded mt7530 driver
349 +[ 4.967662] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 21
350 +[ 4.978262] NET: Registered protocol family 10
351 +[ 4.984286] Segment Routing with IPv6
352 +[ 4.988020] NET: Registered protocol family 17
353 +[ 4.992556] 8021q: 802.1Q VLAN Support v1.8
354 +[ 4.999621] UBI: auto-attach mtd9
355 +[ 5.003015] ubi0: attaching mtd9
356 +[ 5.033798] UBI: EOF marker found, PEBs from 25 will be erased
357 +[ 5.039967] ubi0: scanning is finished
358 +[ 5.081872] ubi0: volume 1 ("rootfs_data") re-sized from 9 to 258 LEBs
359 +[ 5.089203] ubi0: attached mtd9 (name "ubi", size 38 MiB)
360 +[ 5.094644] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
361 +[ 5.101543] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
362 +[ 5.108298] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
363 +[ 5.115245] ubi0: good PEBs: 297, bad PEBs: 7, corrupted PEBs: 0
364 +[ 5.121247] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
365 +[ 5.128436] ubi0: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number:
366 +[ 5.137541] ubi0: available PEBs: 0, total reserved PEBs: 297, PEBs reserved for bad PEB handling: 13
367 +[ 5.146764] ubi0: background thread "ubi_bgt0d" started, PID 378
368 +[ 5.148847] block ubiblock0_0: created from ubi0:0(rootfs)
369 +[ 5.158262] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem
370 +[ 5.165234] hctosys: unable to open rtc device (rtc0)
371 +[ 5.183831] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
372 +[ 5.195491] Freeing unused kernel memory: 1260K
373 +[ 5.200022] This architecture does not have kernel memory protection.
374 +[ 5.783744] init: Console is alive
375 +[ 5.787378] init: - watchdog -
376 +[ 6.295000] mtk_soc_eth 1e100000.ethernet eth0: port 1 link up
377 +[ 6.502425] kmodloader: loading kernel modules from /etc/modules-boot.d/*
378 +[ 6.591413] usbcore: registered new interface driver usbfs
379 +[ 6.596966] usbcore: registered new interface driver hub
380 +[ 6.602453] usbcore: registered new device driver usb
381 +[ 6.615285] SCSI subsystem initialized
382 +[ 6.626976] xhci-mtk 1e1c0000.xhci: 1e1c0000.xhci supply vbus not found, using dummy regulator
383 +[ 6.635689] xhci-mtk 1e1c0000.xhci: 1e1c0000.xhci supply vusb33 not found, using dummy regulator
384 +[ 6.644627] xhci-mtk 1e1c0000.xhci: xHCI Host Controller
385 +[ 6.649947] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 1
386 +[ 6.660739] xhci-mtk 1e1c0000.xhci: hcc params 0x01401198 hci version 0x96 quirks 0x0000000000210010
387 +[ 6.669906] xhci-mtk 1e1c0000.xhci: irq 20, io mem 0x1e1c0000
388 +[ 6.676639] hub 1-0:1.0: USB hub found
389 +[ 6.680467] hub 1-0:1.0: 2 ports detected
390 +[ 6.685052] xhci-mtk 1e1c0000.xhci: xHCI Host Controller
391 +[ 6.690366] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 2
392 +[ 6.697886] xhci-mtk 1e1c0000.xhci: Host supports USB 3.0 SuperSpeed
393 +[ 6.704507] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
394 +[ 6.713446] hub 2-0:1.0: USB hub found
395 +[ 6.717275] hub 2-0:1.0: 1 port detected
396 +[ 6.727313] usbcore: registered new interface driver usb-storage
397 +[ 6.733578] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
398 +[ 6.750877] init: - preinit -
399 +[ 7.180814] usb 2-1: new SuperSpeed USB device number 2 using xhci-mtk
400 +[ 7.212805] random: procd: uninitialized urandom read (4 bytes read)
401 +[ 7.212971] usb-storage 2-1:1.0: USB Mass Storage device detected
402 +[ 7.225920] scsi host0: usb-storage 2-1:1.0
403 +[ 7.366240] mtk_soc_eth 1e100000.ethernet: PPE started
221 221  Press the [f] key and hit [enter] to enter failsafe mode
222 222  Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
223 -[ 5.312718] random: procd: uninitialized urandom read (4 bytes read)
224 -[ 6.273781] scsi 0:0:0:0: Direct-Access SanDisk Ultra Fit 1.00 PQ: 0 ANSI: 6
225 -[ 6.283479] sd 0:0:0:0: [sda] 60063744 512-byte logical blocks: (30.8 GB/28.6 GiB)
226 -[ 6.291556] sd 0:0:0:0: [sda] Write Protect is off
227 -[ 6.297040] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
228 -[ 6.313010] sd 0:0:0:0: [sda] Attached SCSI removable disk
229 -[ 8.450677] UBIFS (ubi0:1): default file-system created
230 -[ 8.457372] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 474
231 -[ 8.568317] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
232 -[ 8.576154] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
233 -[ 8.586040] UBIFS (ubi0:1): FS size: 32886784 bytes (31 MiB, 259 LEBs), journal size 1650688 bytes (1 MiB, 13 LEBs)
234 -[ 8.596442] UBIFS (ubi0:1): reserved for root: 1553323 bytes (1516 KiB)
235 -[ 8.603051] UBIFS (ubi0:1): media format: w4/r0 (latest is w5/r0), UUID D42C5178-C937-4CB4-94EE-0031FFF6550A, small LPT model
236 -[ 8.617248] mount_root: overlay filesystem has not been fully initialized yet
237 -[ 8.624849] mount_root: switching to ubifs overlay
238 -[ 8.647505] urandom-seed: Seed file not found (/etc/urandom.seed)
239 -[ 8.728797] mtk_soc_eth 1e100000.ethernet: 0x100 = 0x6060000c, 0x10c = 0x80818
240 -[ 8.743450] procd: - early -
241 -[ 8.746426] procd: - watchdog -
242 -[ 9.403107] procd: - watchdog -
243 -[ 9.406559] procd: - ubus -
244 -[ 9.457080] random: ubusd: uninitialized urandom read (4 bytes read)
245 -[ 9.464255] random: ubusd: uninitialized urandom read (4 bytes read)
246 -[ 9.470985] random: ubusd: uninitialized urandom read (4 bytes read)
247 -[ 9.478186] procd: - init -
406 +[ 10.582466] UBIFS (ubi0:1): default file-system created
407 +[ 10.589130] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 496
408 +[ 10.700430] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
409 +[ 10.708276] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
410 +[ 10.718161] UBIFS (ubi0:1): FS size: 31490048 bytes (30 MiB, 248 LEBs), journal size 1523712 bytes (1 MiB, 12 LEBs)
411 +[ 10.728565] UBIFS (ubi0:1): reserved for root: 1487352 bytes (1452 KiB)
412 +[ 10.735166] UBIFS (ubi0:1): media format: w4/r0 (latest is w5/r0), UUID , small LPT model
413 +[ 10.749347] mount_root: overlay filesystem has not been fully initialized yet
414 +[ 10.756981] mount_root: switching to ubifs overlay
415 +[ 10.781065] urandom-seed: Seed file not found (/etc/urandom.seed)
416 +[ 10.861172] mtk_soc_eth 1e100000.ethernet: 0x100 = 0x6060000c, 0x10c = 0x80818
417 +[ 10.876085] procd: - early -
418 +[ 10.879061] procd: - watchdog -
419 +[ 11.550737] procd: - watchdog -
420 +[ 11.554202] procd: - ubus -
421 +[ 11.583502] random: ubusd: uninitialized urandom read (4 bytes read)
422 +[ 11.611421] random: ubusd: uninitialized urandom read (4 bytes read)
423 +[ 11.618117] random: ubusd: uninitialized urandom read (4 bytes read)
424 +[ 11.625387] procd: - init -
248 248  Please press Enter to activate this console.
249 -[ 9.714720] kmodloader: loading kernel modules from /etc/modules.d/*
250 -[ 9.724486] ip6_tables: (C) 2000-2006 Netfilter Core Team
251 -[ 9.738298] ip_tables: (C) 2000-2006 Netfilter Core Team
252 -[ 9.749820] nf_conntrack version 0.5.0 (4096 buckets, 16384 max)
253 -[ 9.790837] xt_time: kernel timezone is -0000
254 -[ 9.801201] PPP generic driver version 2.4.2
255 -[ 9.806822] NET: Registered protocol family 24
256 -[ 9.813785] kmodloader: done loading kernel modules from /etc/modules.d/*
257 -[ 10.951148] urandom_read: 5 callbacks suppressed
258 -[ 10.951161] random: jshn: uninitialized urandom read (4 bytes read)
259 -[ 16.501675] mtk_soc_eth 1e100000.ethernet: PPE started
260 -[ 16.512395] br-lan: port 1(eth0.2) entered blocking state
261 -[ 16.517965] br-lan: port 1(eth0.2) entered disabled state
262 -[ 16.523873] device eth0.2 entered promiscuous mode
263 -[ 16.528744] device eth0 entered promiscuous mode
264 -[ 16.537326] br-lan: port 1(eth0.2) entered blocking state
265 -[ 16.542760] br-lan: port 1(eth0.2) entered forwarding state
266 -[ 16.548768] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
267 -[ 17.553672] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
268 -[ 21.883773] random: crng init done
269 -
426 +[ 12.046531] kmodloader: loading kernel modules from /etc/modules.d/*
427 +[ 12.057746] ip6_tables: (C) 2000-2006 Netfilter Core Team
428 +[ 12.069204] Loading modules backported from Linux version v5.3-rc4-0-gd45331b00ddb
429 +[ 12.076775] Backport generated by backports.git v5.3-rc4-1-0-g4ec72687
430 +[ 12.085114] ip_tables: (C) 2000-2006 Netfilter Core Team
431 +[ 12.096731] nf_conntrack version 0.5.0 (4096 buckets, 16384 max)
432 +[ 12.127574] urngd: v1.0.0 started.
433 +[ 12.145053] xt_time: kernel timezone is -0000
434 +[ 12.214244] bus=0x1, slot = 0x0, irq=0x0
435 +[ 12.218201] PCI: Enabling device 0000:00:00.0 (0004 -> 0006)
436 +[ 12.241178] mt7615e 0000:01:00.0: HW/SW Version: 0x8a108a10, Build Time: 20180518100604a
437 +[ 12.241178]
438 +[ 12.266469] random: crng init done
439 +[ 12.269877] random: 6 urandom warning(s) missed due to ratelimiting
440 +[ 12.456236] mt7615e 0000:01:00.0: N9 Firmware Version: _reserved_, Build Time: 20190103180756
441 +[ 12.471995] mt7615e 0000:01:00.0: CR4 Firmware Version: _reserved_, Build Time: 20181207140436
442 ++ýýrýýýýýýýbus=0x2, slot = 0x1, irq=0x0
443 +[ 20.131310] PCI: Enabling device 0000:00:01.0 (0004 -> 0006)
444 +[ 20.161193] mt7615e 0000:02:00.0: HW/SW Version: 0x8a108a10, Build Time: 20180518100604a
445 +[ 20.161193]
446 +[ 20.185604] mt7615e 0000:02:00.0: N9 Firmware Version: _reserved_, Build Time: 20190103180756
447 +[ 20.200746] mt7615e 0000:02:00.0: CR4 Firmware Version: _reserved_, Build Time: 20181207140436
448 +[ 27.852570] PPP generic driver version 2.4.2
449 +[ 27.858358] NET: Registered protocol family 24
450 +[ 27.866716] kmodloader: done loading kernel modules from /etc/modules.d/*
451 +[ 41.276638] mtk_soc_eth 1e100000.ethernet: PPE started
452 +[ 41.287935] br-lan: port 1(eth0.2) entered blocking state
453 +[ 41.293420] br-lan: port 1(eth0.2) entered disabled state
454 +[ 41.299522] device eth0.2 entered promiscuous mode
455 +[ 41.304484] device eth0 entered promiscuous mode
456 +[ 41.311947] br-lan: port 1(eth0.2) entered blocking state
457 +[ 41.317384] br-lan: port 1(eth0.2) entered forwarding state
458 +[ 41.323511] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
459 +[ 42.321086] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
270 270  
271 271  
272 -BusyBox v1.30.1 () built-in shell (ash)
273 273  
274 - ~_~_~_~_~_~__ ~_~_~_~_~_~_~_~_ ~_~_
275 - ~| |.~-~-~-~--.~-~-~-~--.~-~-~-~--.| | | |.~-~-~-~-.| |_
276 - ~| - || _ | -~_~_| || | | || _|| _|
277 - ~|~_~_~_~_~_~__|| ~_~_|~_~_~_~__|~_~_|~_~_||~_~_~_~_~_~_~_~_||~_~_| |~_~_~_~_|
278 - ~|~_~_| W I R E L E S S F R E E D O M
279 - ~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~--
280 - OpenWrt SNAPSHOT, r9254+122-3b40121530
281 - ~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~--
282 -~=== WARNING! =====================================
463 +BusyBox v1.31.0 () built-in shell (ash)
464 +
465 + _______ ________ __
466 + | |.-----.-----.-----.| | | |.----.| |_
467 + | - || _ | -__| || | | || _|| _|
468 + |_______|| __|_____|__|__||________||__| |____|
469 + |__| W I R E L E S S F R E E D O M
470 + -----------------------------------------------------
471 + OpenWrt SNAPSHOT, r10942-9bebafcb5d
472 + -----------------------------------------------------
473 +=== WARNING! =====================================
283 283  There is no root password defined on this device!
284 284  Use the "passwd" command to set up a new password
285 285  in order to prevent unauthorized SSH logins.
286 -~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-~-
287 -root@OpenWrt:/# free
288 - total used free shared buff/cache available
289 -Mem: 253572 23256 224316 60 6000 203516
290 -Swap: 0 0 0
291 -root@OpenWrt:/# df -h
477 +--------------------------------------------------
478 +root@OpenWrt:/# ifconfig -a
479 +br-lan Link encap:Ethernet HWaddr
480 + inet addr:192.168.1.1 Bcast:192.168.1.255 Mask:255.255.255.0
481 + inet6 addr: fde0:62db:5134::1/60 Scope:Global
482 + inet6 addr: fe80::/64 Scope:Link
483 + UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
484 + RX packets:41 errors:0 dropped:0 overruns:0 frame:0
485 + TX packets:13 errors:0 dropped:0 overruns:0 carrier:0
486 + collisions:0 txqueuelen:1000
487 + RX bytes:8012 (7.8 KiB) TX bytes:2126 (2.0 KiB)
488 +
489 +eth0 Link encap:Ethernet HWaddr
490 + inet6 addr: fe80::/64 Scope:Link
491 + UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
492 + RX packets:102 errors:0 dropped:0 overruns:0 frame:0
493 + TX packets:47 errors:0 dropped:0 overruns:0 carrier:0
494 + collisions:0 txqueuelen:1000
495 + RX bytes:19418 (18.9 KiB) TX bytes:8199 (8.0 KiB)
496 + Interrupt:21
497 +
498 +eth0.1 Link encap:Ethernet HWaddr
499 + inet6 addr: fe80::/64 Scope:Link
500 + UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
501 + RX packets:0 errors:0 dropped:0 overruns:0 frame:0
502 + TX packets:20 errors:0 dropped:0 overruns:0 carrier:0
503 + collisions:0 txqueuelen:1000
504 + RX bytes:0 (0.0 B) TX bytes:3368 (3.2 KiB)
505 +
506 +eth0.2 Link encap:Ethernet HWaddr
507 + UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
508 + RX packets:41 errors:0 dropped:0 overruns:0 frame:0
509 + TX packets:13 errors:0 dropped:0 overruns:0 carrier:0
510 + collisions:0 txqueuelen:1000
511 + RX bytes:8012 (7.8 KiB) TX bytes:2126 (2.0 KiB)
512 +
513 +lo Link encap:Local Loopback
514 + inet addr:127.0.0.1 Mask:255.0.0.0
515 + inet6 addr: ::1/128 Scope:Host
516 + UP LOOPBACK RUNNING MTU:65536 Metric:1
517 + RX packets:28 errors:0 dropped:0 overruns:0 frame:0
518 + TX packets:28 errors:0 dropped:0 overruns:0 carrier:0
519 + collisions:0 txqueuelen:1000
520 + RX bytes:1904 (1.8 KiB) TX bytes:1904 (1.8 KiB)
521 +
522 +wlan0 Link encap:Ethernet HWaddr
523 + BROADCAST MULTICAST MTU:1500 Metric:1
524 + RX packets:0 errors:0 dropped:0 overruns:0 frame:0
525 + TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
526 + collisions:0 txqueuelen:1000
527 + RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
528 +
529 +wlan1 Link encap:Ethernet HWaddr
530 + BROADCAST MULTICAST MTU:1500 Metric:1
531 + RX packets:0 errors:0 dropped:0 overruns:0 frame:0
532 + TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
533 + collisions:0 txqueuelen:1000
534 + RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
535 +
536 +root@OpenWrt:/# ls -l
537 +drwxr-xr-x 2 root root 778 Sep 1 06:04 bin
538 +drwxr-xr-x 4 root root 1300 Sep 1 06:05 dev
539 +drwxr-xr-x 1 root root 512 Sep 1 06:05 etc
540 +-rwxr-xr-x 1 root root 78 Dec 30 2018 init
541 +drwxr-xr-x 11 root root 426 Sep 1 06:04 lib
542 +drwxr-xr-x 2 root root 3 Sep 1 06:04 mnt
543 +drwxr-xr-x 4 root root 360 Sep 1 06:05 overlay
544 +dr-xr-xr-x 73 root root 0 Jan 1 1970 proc
545 +drwxr-xr-x 16 root root 223 Sep 1 06:04 rom
546 +drwxr-xr-x 2 root root 3 Sep 1 06:04 root
547 +drwxr-xr-x 2 root root 822 Sep 1 06:04 sbin
548 +dr-xr-xr-x 11 root root 0 Jan 1 1970 sys
549 +drwxrwxrwt 15 root root 380 Sep 1 06:05 tmp
550 +drwxr-xr-x 7 root root 89 Sep 1 06:04 usr
551 +lrwxrwxrwx 1 root root 3 Sep 1 06:04 var -> tmp
552 +drwxr-xr-x 2 root root 3 Sep 1 06:04 www
553 +root@OpenWrt:/# ps
554 + PID USER VSZ STAT COMMAND
555 + 1 root 1576 S /sbin/procd
556 + 2 root 0 SW [kthreadd]
557 + 3 root 0 IW [kworker/0:0]
558 + 4 root 0 IW< [kworker/0:0H]
559 + 5 root 0 IW [kworker/u8:0]
560 + 6 root 0 IW< [mm_percpu_wq]
561 + 7 root 0 SW [ksoftirqd/0]
562 + 8 root 0 IW [rcu_sched]
563 + 9 root 0 IW [rcu_bh]
564 + 10 root 0 SW [migration/0]
565 + 11 root 0 SW [cpuhp/0]
566 + 12 root 0 SW [cpuhp/1]
567 + 13 root 0 SW [migration/1]
568 + 14 root 0 SW [ksoftirqd/1]
569 + 16 root 0 IW< [kworker/1:0H]
570 + 17 root 0 SW [cpuhp/2]
571 + 18 root 0 SW [migration/2]
572 + 19 root 0 SW [ksoftirqd/2]
573 + 21 root 0 IW< [kworker/2:0H]
574 + 22 root 0 SW [cpuhp/3]
575 + 23 root 0 SW [migration/3]
576 + 24 root 0 SW [ksoftirqd/3]
577 + 25 root 0 IW [kworker/3:0]
578 + 26 root 0 IW< [kworker/3:0H]
579 + 27 root 0 IW< [netns]
580 + 41 root 0 IW [kworker/u8:3]
581 + 68 root 0 IW [kworker/3:1]
582 + 69 root 0 IW [kworker/2:1]
583 + 138 root 0 IW [kworker/1:1]
584 + 139 root 0 SW [oom_reaper]
585 + 140 root 0 IW< [writeback]
586 + 142 root 0 SW [kcompactd0]
587 + 143 root 0 IW< [crypto]
588 + 145 root 0 IW< [kblockd]
589 + 175 root 0 IW< [watchdogd]
590 + 199 root 0 SW [kswapd0]
591 + 268 root 0 IW< [pencrypt]
592 + 270 root 0 IW< [pdecrypt]
593 + 366 root 0 IW< [ipv6_addrconf]
594 + 378 root 0 SW [ubi_bgt0d]
595 + 383 root 0 IW< [kworker/0:1H]
596 + 384 root 0 IW< [kworker/2:1H]
597 + 385 root 0 IW [kworker/2:2]
598 + 386 root 0 IW< [kworker/3:1H]
599 + 389 root 0 IW< [kworker/1:1H]
600 + 429 root 0 IW [kworker/0:2]
601 + 437 root 0 IW [kworker/1:2]
602 + 453 root 0 SW [scsi_eh_0]
603 + 454 root 0 IW< [scsi_tmf_0]
604 + 455 root 0 SW [usb-storage]
605 + 496 root 0 SW [ubifs_bgt0_1]
606 + 573 root 1220 S /sbin/ubusd
607 + 574 root 1220 S /bin/ash --login
608 + 591 root 1028 S /sbin/urngd
609 + 660 root 0 IW< [cfg80211]
610 + 1012 root 1248 S /sbin/logd -S 64
611 + 1074 dnsmasq 1344 S /usr/sbin/dnsmasq -C /var/etc/dnsmasq.conf.cfg01411c
612 + 1111 root 1080 S /usr/sbin/dropbear -F -P /var/run/dropbear.1.pid -p
613 + 1168 root 1700 S /sbin/netifd
614 + 1204 root 1448 S /usr/sbin/odhcpd
615 + 1360 root 1212 S udhcpc -p /var/run/udhcpc-eth0.1.pid -s /lib/netifd/
616 + 1361 root 1052 S odhcp6c -s /lib/netifd/dhcpv6.script -P0 -t120 eth0.
617 + 1391 root 1212 S< /usr/sbin/ntpd -n -N -S /usr/sbin/ntpd-hotplug -p 0.
618 + 1720 root 1212 R ps
619 +root@OpenWrt:/etc# ping www.google.co
620 +PING www.google.co (): 56 data bytes
621 +64 bytes from : seq=0 ttl=52 time=4.718 ms
622 +^C
623 +--- www.google.co ping statistics ---
624 +1 packets transmitted, 1 packets received, 0% packet loss
625 +round-trip min/avg/max = 4.718/4.718/4.718 ms
626 +root@OpenWrt:/etc# ping www.google.com
627 +PING www.google.com (): 56 data bytes
628 +64 bytes from : seq=0 ttl=47 time=4.927 ms
629 +64 bytes from : seq=1 ttl=47 time=4.687 ms
630 +^C
631 +--- www.google.com ping statistics ---
632 +2 packets transmitted, 2 packets received, 0% packet loss
633 +round-trip min/avg/max = 4.687/4.807/4.927 ms
634 +root@OpenWrt:/etc# opkg update
635 +Downloading http://downloads.openwrt.org/snapshots/targets/ramips/mt7621/packages/Packages.gz
636 +Updated list of available packages in /var/opkg-lists/openwrt_core
637 +Downloading http://downloads.openwrt.org/snapshots/targets/ramips/mt7621/packages/Packages.sig
638 +Signature check passed.
639 +Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/base/Packages.gz
640 +Updated list of available packages in /var/opkg-lists/openwrt_base
641 +Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/base/Packages.sig
642 +Signature check passed.
643 +Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/Packages.gz
644 +Updated list of available packages in /var/opkg-lists/openwrt_luci
645 +Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/Packages.sig
646 +Signature check passed.
647 +Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/packages/Packages.gz
648 +Updated list of available packages in /var/opkg-lists/openwrt_packages
649 +Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/packages/Packages.sig
650 +Signature check passed.
651 +Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/routing/Packages.gz
652 +Updated list of available packages in /var/opkg-lists/openwrt_routing
653 +Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/routing/Packages.sig
654 +Signature check passed.
655 +Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/telephony/Packages.gz
656 +Updated list of available packages in /var/opkg-lists/openwrt_telephony
657 +Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/telephony/Packages.sig
658 +Signature check passed.
659 +root@OpenWrt:/etc# opkg install luci
660 +Installing luci (git-19.241.65047-dffe9ca-1) to root...
661 +Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/luci_git-19.241.65047-dffe9ca-1_all.ipk
662 +Installing uhttpd (2019-08-17-6b03f960-3) to root...
663 +Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/base/uhttpd_2019-08-17-6b03f960-3_mipsel_24kc.ipk
664 +Installing liblua5.1.5 (5.1.5-5) to root...
665 +Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/base/liblua5.1.5_5.1.5-5_mipsel_24kc.ipk
666 +Installing lua (5.1.5-5) to root...
667 +Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/base/lua_5.1.5-5_mipsel_24kc.ipk
668 +Installing luci-lib-nixio (git-19.241.65047-dffe9ca-1) to root...
669 +Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/luci-lib-nixio_git-19.241.65047-dffe9ca-1_mipsel_24kc.ipk
670 +Installing luci-lib-ip (git-19.241.65047-dffe9ca-1) to root...
671 +Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/luci-lib-ip_git-19.241.65047-dffe9ca-1_mipsel_24kc.ipk
672 +Installing rpcd (2019-06-05-89bfaa42-3) to root...
673 +Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/base/rpcd_2019-06-05-89bfaa42-3_mipsel_24kc.ipk
674 +Installing libubus-lua (2018-10-06-221ce7e7-1) to root...
675 +Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/base/libubus-lua_2018-10-06-221ce7e7-1_mipsel_24kc.ipk
676 +Installing luci-lib-jsonc (git-19.241.65047-dffe9ca-1) to root...
677 +Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/luci-lib-jsonc_git-19.241.65047-dffe9ca-1_mipsel_24kc.ipk
678 +Installing liblucihttp0 (2019-07-05-a34a17d5-1) to root...
679 +Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/liblucihttp0_2019-07-05-a34a17d5-1_mipsel_24kc.ipk
680 +Installing liblucihttp-lua (2019-07-05-a34a17d5-1) to root...
681 +Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/liblucihttp-lua_2019-07-05-a34a17d5-1_mipsel_24kc.ipk
682 +Installing luci-base (git-19.241.65047-dffe9ca-1) to root...
683 +Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/luci-base_git-19.241.65047-dffe9ca-1_mipsel_24kc.ipk
684 +Installing libiwinfo-lua (2019-08-28-a9f95570-1) to root...
685 +Downloading http://downloads.openwrt.org/snapshots/targets/ramips/mt7621/packages/libiwinfo-lua_2019-08-28-a9f95570-1_mipsel_24kc.ipk
686 +Installing luci-mod-status (git-19.241.65047-dffe9ca-1) to root...
687 +Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/luci-mod-status_git-19.241.65047-dffe9ca-1_mipsel_24kc.ipk
688 +Installing luci-mod-system (git-19.241.65047-dffe9ca-1) to root...
689 +Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/luci-mod-system_git-19.241.65047-dffe9ca-1_all.ipk
690 +Installing luci-mod-network (git-19.241.65047-dffe9ca-1) to root...
691 +Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/luci-mod-network_git-19.241.65047-dffe9ca-1_all.ipk
692 +Installing luci-mod-admin-full (git-19.241.65047-dffe9ca-1) to root...
693 +Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/luci-mod-admin-full_git-19.241.65047-dffe9ca-1_all.ipk
694 +Installing luci-theme-bootstrap (git-19.241.65047-dffe9ca-1) to root...
695 +Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/luci-theme-bootstrap_git-19.241.65047-dffe9ca-1_all.ipk
696 +Installing luci-app-firewall (git-19.241.65047-dffe9ca-1) to root...
697 +Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/luci-app-firewall_git-19.241.65047-dffe9ca-1_all.ipk
698 +Installing luci-app-opkg (git-19.241.65047-dffe9ca-1) to root...
699 +Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/luci-app-opkg_git-19.241.65047-dffe9ca-1_all.ipk
700 +Installing luci-proto-ppp (git-19.241.65047-dffe9ca-1) to root...
701 +Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/luci-proto-ppp_git-19.241.65047-dffe9ca-1_all.ipk
702 +Installing luci-proto-ipv6 (git-19.241.65047-dffe9ca-1) to root...
703 +Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/luci-proto-ipv6_git-19.241.65047-dffe9ca-1_all.ipk
704 +Installing rpcd-mod-rrdns (20170710) to root...
705 +Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/rpcd-mod-rrdns_20170710_mipsel_24kc.ipk
706 +Configuring liblucihttp0.
707 +Configuring luci-app-opkg.
708 +Configuring rpcd.
709 +Configuring liblua5.1.5.
710 +Configuring luci-lib-ip.
711 +Configuring libubus-lua.
712 +Configuring libiwinfo-lua.
713 +Configuring lua.
714 +Configuring luci-lib-nixio.
715 +Configuring luci-lib-jsonc.
716 +Configuring liblucihttp-lua.
717 +Configuring luci-base.
718 +Configuring luci-mod-system.
719 +Configuring luci-theme-bootstrap.
720 +Configuring luci-mod-status.
721 +Configuring luci-app-firewall.
722 +Configuring luci-proto-ppp.
723 +Configuring luci-mod-network.
724 +Configuring luci-mod-admin-full.
725 +Configuring luci-proto-ipv6.
726 +Configuring uhttpd.
727 +Configuring rpcd-mod-rrdns.
728 +Configuring luci.
729 +root@OpenWrt:/etc# df -h
292 292  Filesystem Size Used Available Use% Mounted on
293 -/dev/root 1.5M 1.5M 0 100% /rom
294 -tmpfs 123.8M 60.0K 123.8M 0% /tmp
295 -/dev/ubi0_1 28.3M 36.0K 26.8M 0% /overlay
296 -overlayfs:/overlay 28.3M 36.0K 26.8M 0% /
297 -tmpfs 512.0K 0 512.0K 0% /dev</code>
731 +/dev/root 2.8M 2.8M 0 100% /rom
732 +tmpfs 123.5M 764.0K 122.8M 1% /tmp
733 +/dev/ubi0_1 27.1M 1.4M 24.3M 5% /overlay
734 +overlayfs:/overlay 27.1M 1.4M 24.3M 5% /
735 +tmpfs 512.0K 0 512.0K 0% /dev
736 +root@OpenWrt:/etc# [ 2075.963720] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
737 +[ 2075.973245] br-lan: port 2(wlan0) entered blocking state
738 +[ 2075.978551] br-lan: port 2(wlan0) entered disabled state
739 +[ 2075.984368] device wlan0 entered promiscuous mode
740 +[ 2087.165173] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
741 +[ 2087.171890] br-lan: port 2(wlan0) entered blocking state
742 +[ 2087.177194] br-lan: port 2(wlan0) entered forwarding state
743 +[ 2096.494533] device wlan0 left promiscuous mode
744 +[ 2096.499322] br-lan: port 2(wlan0) entered disabled state
745 +[ 2097.382887] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
746 +[ 2097.393568] br-lan: port 2(wlan0) entered blocking state
747 +[ 2097.398924] br-lan: port 2(wlan0) entered disabled state
748 +[ 2097.404922] device wlan0 entered promiscuous mode
749 +[ 2097.409972] br-lan: port 2(wlan0) entered blocking state
750 +[ 2097.415296] br-lan: port 2(wlan0) entered forwarding state
751 +[ 2097.749351] br-lan: port 2(wlan0) entered disabled state
752 +[ 2107.953875] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
753 +[ 2107.960561] br-lan: port 2(wlan0) entered blocking state
754 +[ 2107.965861] br-lan: port 2(wlan0) entered forwarding state
755 +[ 2117.964353] device wlan0 left promiscuous mode
756 +[ 2117.969130] br-lan: port 2(wlan0) entered disabled state
757 +[ 2118.782586] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
758 +[ 2118.792816] br-lan: port 2(wlan0) entered blocking state
759 +[ 2118.798173] br-lan: port 2(wlan0) entered disabled state
760 +[ 2118.804171] device wlan0 entered promiscuous mode
761 +[ 2118.809362] br-lan: port 2(wlan0) entered blocking state
762 +[ 2118.814692] br-lan: port 2(wlan0) entered forwarding state
763 +[ 2119.189273] br-lan: port 2(wlan0) entered disabled state
764 +[ 2130.258107] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
765 +[ 2130.264811] br-lan: port 2(wlan0) entered blocking state
766 +[ 2130.270163] br-lan: port 2(wlan0) entered forwarding state
767 +[ 2245.748473] device wlan0 left promiscuous mode
768 +[ 2245.753145] br-lan: port 2(wlan0) entered disabled state
769 +[ 2246.536062] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
770 +[ 2246.546273] br-lan: port 2(wlan0) entered blocking state
771 +[ 2246.551680] br-lan: port 2(wlan0) entered disabled state
772 +[ 2246.557667] device wlan0 entered promiscuous mode
773 +[ 2246.562855] br-lan: port 2(wlan0) entered blocking state
774 +[ 2246.568267] br-lan: port 2(wlan0) entered forwarding state
775 +[ 2246.838430] br-lan: port 2(wlan0) entered disabled state
776 +[ 2246.948147] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
777 +[ 2246.954850] br-lan: port 2(wlan1) entered blocking state
778 +[ 2246.960197] br-lan: port 2(wlan1) entered forwarding state
779 +
780 +root@OpenWrt:/etc#
781 +root@OpenWrt:/etc# uci show wireless
782 +wireless.radio0=wifi-device
783 +wireless.radio0.type='mac80211'
784 +wireless.radio0.channel='11'
785 +wireless.radio0.hwmode='11g'
786 +wireless.radio0.path='pci0000:00/0000:00:00.0/0000:01:00.0'
787 +wireless.radio0.country='00'
788 +wireless.radio0.legacy_rates='1'
789 +wireless.radio0.htmode='HT20'
790 +wireless.default_radio0=wifi-iface
791 +wireless.default_radio0.device='radio0'
792 +wireless.default_radio0.network='lan'
793 +wireless.default_radio0.mode='ap'
794 +wireless.default_radio0.encryption='psk2'
795 +wireless.default_radio0.key='qwerty1234'
796 +wireless.default_radio0.ssid='asdf'
797 +wireless.radio1=wifi-device
798 +wireless.radio1.type='mac80211'
799 +wireless.radio1.channel='36'
800 +wireless.radio1.hwmode='11a'
801 +wireless.radio1.path='pci0000:00/0000:00:01.0/0000:02:00.0'
802 +wireless.radio1.htmode='VHT80'
803 +wireless.radio1.__toggle='Enable'
804 +wireless.radio1.country='00'
805 +wireless.radio1.legacy_rates='1'
806 +wireless.default_radio1=wifi-iface
807 +wireless.default_radio1.device='radio1'
808 +wireless.default_radio1.network='lan'
809 +wireless.default_radio1.mode='ap'
810 +wireless.default_radio1.ssid='asdf'
811 +wireless.default_radio1.encryption='psk2'
812 +wireless.default_radio1.key='qwerty1234'
813 +root@OpenWrt:/etc#
814 +{{/code}}
815 +
816 +Firmware:
817 +
818 +./staging_dir/target-mipsel_24kc_glibc/root-ramips/lib/firmware/mediatek/mt7615_rom_patch.bin
1567332570723-651.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.CodePowered
Size
... ... @@ -1,0 +1,1 @@
1 +166.8 KB
Content
openwrt-ramips-mt7621-ea8100-initramfs-kernel.bin
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.CodePowered
Size
... ... @@ -1,0 +1,1 @@
1 +3.2 MB
Content
openwrt-ramips-mt7621-ea8100-squashfs-sysupgrade.bin
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.CodePowered
Size
... ... @@ -1,0 +1,1 @@
1 +4.3 MB
Content
openwrt-ramips-mt7621-linksys_ea8100-initramfs-kernel-9bebafcb5dfe37f25285fa18fb8bfe7b68011267.bin
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.CodePowered
Size
... ... @@ -1,0 +1,1 @@
1 +4.5 MB
Content
openwrt-ramips-mt7621-linksys_ea8100-squashfs-sysupgrade-9bebafcb5dfe37f25285fa18fb8bfe7b68011267.bin
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.CodePowered
Size
... ... @@ -1,0 +1,1 @@
1 +5.6 MB
Content
XWiki.XWikiComments[0]
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.ugene
Comment
... ... @@ -1,0 +1,1 @@
1 +Thanks for sharing!
Date
... ... @@ -1,0 +1,1 @@
1 +2019-05-09 16:42:45.0