Last modified by Leon Poon on 2021/07/16 18:40
From version 24.1
edited by Leon Poon
on 2020/05/31 14:27
Change comment: There is no comment for this version
To version 11.1
edited by Leon Poon
on 2019/09/01 10:13
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -1,39 +1,8 @@
1 1  switch0: port 0 = wan, port 1,2,3,4 = lan
2 2  
3 -If you brick your router you should be able to recover by soldering the UART pin headers and connecting to the serial. See [[this page for pictures>>doc:Linksys EA8100.WebHome]].
4 4  
4 +[[https:~~/~~/github.com/LeonPoon/openwrt/compare/master...master-linksys_ea8100>>https://github.com/LeonPoon/openwrt/compare/master...master-linksys_ea8100]]
5 5  
6 -= 19.07.x =
7 -
8 -[[https:~~/~~/www.codepowered.com/openwrt/v19.07.3/linksys_ea8100/>>url:https://www.codepowered.com/openwrt/v19.07.3/linksys_ea8100/]] ([[https:~~/~~/github.com/LeonPoon/openwrt/compare/v19.07.3...v19.07.3-linksys_ea8100>>url:https://github.com/LeonPoon/openwrt/compare/v19.07.3...v19.07.3-linksys_ea8100]])
9 -
10 -The EA8100 contains 2 firmware partitions. Using the Linksys UI will flash openwrt into only one of the 2 partitions. The booting process switches partition every few boots, so if you want to always boot into openwrt then you have to flash openwrt into both partitions.
11 -
12 -How to flash:
13 -
14 -If your router currently has stock Linksys firmware:
15 -
16 -1. Flash the "squashfs-factory.img" via Linksys UI, Wait for it to start to reboot.
17 -1. Configure your computer to have ip in 192.168.1.0/24 subnet but NOT 192.168.1.1. (so, use 192.168.1.2.) Start ping to 192.168.1.1.
18 -1. Cross your fingers that the router boots openwrt. Otherwise keep rebooting until it loads the openwrt partition. (Usually 3 times max.) Wait a few minutes from reboot to let it load. If you get response from ping 192.168.1.1 it means openwrt loaded.
19 -1. Scp the "squashfs-sysupgrade.bin" into /tmp in the router. root@192.168.1.1. No password.
20 -1. Log in as root via SSH into shell. No password
21 -1. Sysupgrade the uploaded squashfs-sysupgrade.bin. This should flash the openwrt firmware into both firmware partitions. It auto reboots.
22 -1. opkg update
23 -1. opkg install luci
24 -1. Access LuCI via http:~/~/192.168.1.1/. You can now configure.
25 -
26 -If you are on my 18.x below, sysupgrade will not work. You have to manually mtd write the 19.07 "kernel-initramfs.bin" into the nand and boot/log into it (192.168.1.1), then sysupgrade.
27 -
28 -Sysupgrade will wipe entire firmware partitions! Backup your files/config before sysupgrade.
29 -
30 -Subsequently sysupgrade from 19.07.x should work.
31 -
32 -Wifi seem to work at 30-40MB/s with a MacBook Pro.
33 -
34 -
35 -= 18.x =
36 -
37 37  9bebafcb5dfe37f25285fa18fb8bfe7b68011267 (with wifi support) Download:
38 38  
39 39  * [[initramfs-kernel.bin>>attach:openwrt-ramips-mt7621-linksys_ea8100-initramfs-kernel-9bebafcb5dfe37f25285fa18fb8bfe7b68011267.bin]]
... ... @@ -41,7 +41,7 @@
41 41  
42 42  Note that sysupgrade to a newer image is not likely to work.
43 43  
44 -(% border="1" cellpadding="0" cellspacing="0" style="margin-right:auto; width:auto" %)
13 +(% border="1" cellpadding="0" cellspacing="0" style="margin-right:auto; width: auto" %)
45 45  |[[image:1567332570723-651.png]]
46 46  
47 47  Dmesg:
... ... @@ -753,7 +753,3 @@
753 753  wireless.default_radio1.key='qwerty1234'
754 754  root@OpenWrt:/etc#
755 755  {{/code}}
756 -
757 -Firmware:
758 -
759 -./staging_dir/target-mipsel_24kc_glibc/root-ramips/lib/firmware/mediatek/mt7615_rom_patch.bin