Last modified by Leon Poon on 2021/07/16 18:40
From version 27.1
edited by Leon Poon
on 2020/08/15 03:39
Change comment: There is no comment for this version
To version 19.1
edited by Leon Poon
on 2020/05/31 11:57
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -13,27 +13,24 @@
13 13  
14 14  If your router currently has stock Linksys firmware:
15 15  
16 -1. Flash the "initramfs-factory.img" via Linksys UI. Wait for it to start to reboot.
16 +1. Flash the "squashfs-factory.img" via Linksys UI, Wait for it to start to reboot.
17 17  1. Configure your computer to have ip in 192.168.1.0/24 subnet but NOT 192.168.1.1. (so, use 192.168.1.2.) Start ping to 192.168.1.1.
18 -1. Cross your fingers that the router boots openwrt. Otherwise keep rebooting until it loads the openwrt partition. (Usually 3 times max.) Wait a few minutes from reboot to let it load. If you get ping response from 192.168.1.1 it means openwrt loaded.
19 -1. Scp the "squashfs-sysupgrade.bin" into /tmp in the router. root@192.168.1.1. No password.
20 -1. Log in as root via SSH into shell. No password.
21 -1. Sysupgrade the uploaded squashfs-sysupgrade.bin. This should flash the openwrt firmware into both firmware partitions. It auto reboots.
22 -1. opkg update
23 -1. opkg install luci
24 -1. Access LuCI via http:~/~/192.168.1.1/. You can now configure.
18 +1. Cross your fingers that the router boots openwrt. Otherwise keep rebooting until it loads the openwrt partition. (Usually 3 times max.) Wait a few minutes from reboot to let it load. If you get response from ping 192.168.1.1 it means openwrt loaded.
19 +1. Access LuCI via LAN. (http:~/~/192.168.1.1). Set root password so that SSH server starts. (Do not configure/restart.) This root password is only temporary.
20 +1. Scp the "squashfs-sysupgrade.bin" into /tmp in the router.
21 +1. Log in as root via SSH and the password you set.
22 +1. Sysupgrade the squashfs-sysupgrade.bin. This should flash the openwrt firmware into both firmware partitions. It auto reboots.
23 +1. Access LuCI via 192.168.1.1 again. You can configure for real now.
25 25  
26 -If you are on my 18.x below, sysupgrade will not work. You have to manually mtd write the 19.07 "kernel-initramfs.bin" into the nand and boot/log into it (192.168.1.1), then sysupgrade.
25 +If you are on my 18.x below, sysupgrade will not work. You have to manually mtd write the 19.07 "kernel-initramfs.bin" into the nand and boot into it, then sysupgrade.
27 27  
28 28  Sysupgrade will wipe entire firmware partitions! Backup your files/config before sysupgrade.
29 29  
30 30  Subsequently sysupgrade from 19.07.x should work.
31 31  
32 -Wifi (5Ghz) seem to work at 30-40MB/s with a MacBook Pro.
31 +Wifi seem to work at 30-40MB/s with a MacBook Pro.
33 33  
34 -Known issue: 2.4Ghz wifi performance is really bad. 5Ghz seem ok though.
35 35  
36 -
37 37  = 18.x =
38 38  
39 39  9bebafcb5dfe37f25285fa18fb8bfe7b68011267 (with wifi support) Download: