Last modified by Leon Poon on 2021/07/16 18:40
From version 32.1
edited by Leon Poon
on 2020/09/10 14:25
Change comment: There is no comment for this version
To version 29.1
edited by Leon Poon
on 2020/09/10 13:56
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -7,21 +7,16 @@
7 7  
8 8  19.07.4 is here!
9 9  
10 -Since [[19.07.03>>https://www.codepowered.com/openwrt/v19.07.3/linksys_ea8100/]], as of 19.07.04:
10 +[[https:~~/~~/www.codepowered.com/openwrt/v19.07.4/linksys_ea8100/>>https://www.codepowered.com/openwrt/v19.07.4/linksys_ea8100/]] ([[https:~~/~~/github.com/LeonPoon/openwrt/compare/v19.07.4...v19.07.4-linksys_ea8100>>https://github.com/LeonPoon/openwrt/compare/v19.07.4...v19.07.4-linksys_ea8100]])
11 11  
12 -* Wifi (5Ghz) seem to work at 30-40MB/s with a MacBook Pro.
13 -* **Known issue**: 2.4Ghz wifi performance is really bad. You probably want to disable 2.4Ghz wifi.
14 -
15 -Get images here: [[https:~~/~~/www.codepowered.com/openwrt/v19.07.4/linksys_ea8100/>>https://www.codepowered.com/openwrt/v19.07.4/linksys_ea8100/]] ([[https:~~/~~/github.com/LeonPoon/openwrt/compare/v19.07.4...v19.07.4-linksys_ea8100>>https://github.com/LeonPoon/openwrt/compare/v19.07.4...v19.07.4-linksys_ea8100]])
16 -
17 -**Images do not contain LuCi! (The build process doesn't include it for some reason I have not yet time to figure out.)** You need to follow instructions to get the squashfs.bin flashed, then opkg update and opkg install luci.
18 -
19 19  The EA8100 contains 2 firmware partitions. Using the Linksys UI will flash openwrt into only one of the 2 partitions. The booting process switches partition every few boots, so if you want to always boot into openwrt then you have to flash openwrt into both partitions.
20 20  
21 -How to flash if your router currently has stock Linksys firmware:
14 +How to flash:
22 22  
16 +If your router currently has stock Linksys firmware:
17 +
23 23  1. Flash the "**initramfs-factory.img**" via Linksys UI. Wait for it to start to reboot.
24 -1. Configure your computer to have IP in 192.168.1.0/24 subnet but NOT 192.168.1.1. (so, use 192.168.1.2.) Start ping to 192.168.1.1.
19 +1. Configure your computer to have ip in 192.168.1.0/24 subnet but NOT 192.168.1.1. (so, use 192.168.1.2.) Start ping to 192.168.1.1.
25 25  1. Cross your fingers that the router boots openwrt. Otherwise keep rebooting until it loads the openwrt partition. (Usually 3 times max.) Wait a few minutes from reboot to let it load. If you get ping response from 192.168.1.1 it means openwrt loaded.
26 26  1. Scp the "**squashfs-sysupgrade.bin**" into /tmp in the router. root@192.168.1.1. No password.
27 27  1. Log in as root via SSH into shell. No password.
... ... @@ -34,6 +34,11 @@
34 34  
35 35  Sysupgrade from 19.07.x to another 19.07.y will work. **HOWEVER: **sysupgrade will wipe entire firmware partitions! Backup your files/config before sysupgrade.
36 36  
32 +Since [[19.07.03>>https://www.codepowered.com/openwrt/v19.07.3/linksys_ea8100/]], as of 19.07.04:
33 +
34 +* Wifi (5Ghz) seem to work at 30-40MB/s with a MacBook Pro.
35 +* **Known issue**: 2.4Ghz wifi performance is really bad. 5Ghz seem ok though.
36 +
37 37  = 18.x =
38 38  
39 39  9bebafcb5dfe37f25285fa18fb8bfe7b68011267 (with wifi support) Download: