Last modified by Leon Poon on 2021/07/16 18:40
From version 34.1
edited by Leon Poon
on 2020/09/10 14:46
Change comment: There is no comment for this version
To version 11.1
edited by Leon Poon
on 2019/09/01 10:13
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -1,42 +1,8 @@
1 1  switch0: port 0 = wan, port 1,2,3,4 = lan
2 2  
3 -If you brick your router you should be able to recover by soldering the UART pin headers and connecting to the serial. See [[this page for pictures>>doc:Linksys EA8100.WebHome]].
4 4  
4 +[[https:~~/~~/github.com/LeonPoon/openwrt/compare/master...master-linksys_ea8100>>https://github.com/LeonPoon/openwrt/compare/master...master-linksys_ea8100]]
5 5  
6 -= 19.07.x =
7 -
8 -Openwrt 19.07.4 for EA8100 is here!
9 -
10 -Get images here: [[https:~~/~~/www.codepowered.com/openwrt/v19.07.4/linksys_ea8100/>>https://www.codepowered.com/openwrt/v19.07.4/linksys_ea8100/]] ([[https:~~/~~/github.com/LeonPoon/openwrt/compare/v19.07.4...v19.07.4-linksys_ea8100>>https://github.com/LeonPoon/openwrt/compare/v19.07.4...v19.07.4-linksys_ea8100]])
11 -
12 -Since [[19.07.03>>https://www.codepowered.com/openwrt/v19.07.3/linksys_ea8100/]], as of 19.07.04:
13 -
14 -* Wifi (5Ghz) seem to work at 30-40MB/s with a MacBook Pro.
15 -* **Known issue**: 2.4Ghz wifi performance is really bad. You probably want to disable 2.4Ghz wifi.
16 -
17 -**Images do not contain LuCi! (The build process doesn't include it for some reason I have not yet time to figure out.)** You need to have the **squashfs-sysupgrade.bin** flashed, then install LuCI. (See instructions below.)
18 -
19 -The EA8100 contains 2 firmware partitions. Using the Linksys UI will flash openwrt into only one of the 2 partitions. The booting process switches partition every few boots, so if you want to always boot into openwrt then you have to flash openwrt into both partitions.
20 -
21 -How to flash if your router currently has stock Linksys firmware:
22 -
23 -1. Download the "**openwrt-ramips-mt7621-ea8100-initramfs-kernel-factory.img**" from link above, and flash it via Linksys UI. Wait for it to start to reboot.
24 -1. Configure your computer to have IP in ##192.168.1.2/255.255.255.0##.
25 -1. Check that your router booted Openwrt by visiting [[http:~~/~~/192.168.1.1/>>http://192.168.1.1/]]. It is in Openwrt if you see a white screen with message: "The requested URL /cgi-bin/luci/ was not found on this server." (Luci is not installed currently.) Do a reboot if you see Linksys UI instead, then check again when it boots.
26 -1. Download the "**openwrt-ramips-mt7621-ea8100-squashfs-sysupgrade.bin**" from link above, and upload it into ##/tmp## in the router via SFTP. You can use [[winscp>>https://winscp.net/]] if on Windows. [[root@192.168.1.1>>mailto:root@192.168.1.1]] (No password).
27 -1. Ssh into [[root@192.168.1.1>>mailto:root@192.168.1.1]] (no password). Use [[putty>>https://www.putty.org/]] to ssh if you are on Windows.
28 -1. In the ssh shell run: ##sysupgrade /tmp/openwrt-ramips-mt7621-ea8100-squashfs-sysupgrade.bin##
29 -1. It automatically reboots after a short while. Log in via SSH again.
30 -1. Run: ##opkg update##
31 -1. Run: ##**opkg install luci**##
32 -1. Access LuCI via [[http:~~/~~/192.168.1.1/>>http://192.168.1.1/]]. You can now configure.
33 -
34 -If you are on my 18.x below, sysupgrading to a 19.07 image will not work. You have to manually mtd write the 19.07 "kernel-initramfs.bin" into the nand and boot/log into it (192.168.1.1), then sysupgrade.
35 -
36 -Sysupgrade from 19.07.x to another 19.07.y will work. **HOWEVER: **sysupgrade will wipe entire firmware partitions! Backup your files/config before sysupgrade.
37 -
38 -= 18.x =
39 -
40 40  9bebafcb5dfe37f25285fa18fb8bfe7b68011267 (with wifi support) Download:
41 41  
42 42  * [[initramfs-kernel.bin>>attach:openwrt-ramips-mt7621-linksys_ea8100-initramfs-kernel-9bebafcb5dfe37f25285fa18fb8bfe7b68011267.bin]]
... ... @@ -44,7 +44,7 @@
44 44  
45 45  Note that sysupgrade to a newer image is not likely to work.
46 46  
47 -(% border="1" cellpadding="0" cellspacing="0" style="margin-right:auto; width:auto" %)
13 +(% border="1" cellpadding="0" cellspacing="0" style="margin-right:auto; width: auto" %)
48 48  |[[image:1567332570723-651.png]]
49 49  
50 50  Dmesg:
... ... @@ -756,7 +756,3 @@
756 756  wireless.default_radio1.key='qwerty1234'
757 757  root@OpenWrt:/etc#
758 758  {{/code}}
759 -
760 -Firmware:
761 -
762 -./staging_dir/target-mipsel_24kc_glibc/root-ramips/lib/firmware/mediatek/mt7615_rom_patch.bin