Last modified by Leon Poon on 2021/07/16 18:40
From version 42.1
edited by Leon Poon
on 2020/12/10 15:12
Change comment: There is no comment for this version
To version 35.1
edited by Leon Poon
on 2020/09/10 14:47
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -7,49 +7,34 @@
7 7  
8 8  Openwrt 19.07.4 for EA8100 is here!
9 9  
10 +Get images here: [[https:~~/~~/www.codepowered.com/openwrt/v19.07.4/linksys_ea8100/>>https://www.codepowered.com/openwrt/v19.07.4/linksys_ea8100/]] ([[https:~~/~~/github.com/LeonPoon/openwrt/compare/v19.07.4...v19.07.4-linksys_ea8100>>https://github.com/LeonPoon/openwrt/compare/v19.07.4...v19.07.4-linksys_ea8100]])
11 +
10 10  Since [[19.07.03>>https://www.codepowered.com/openwrt/v19.07.3/linksys_ea8100/]], as of 19.07.04:
11 11  
12 12  * Wifi (5Ghz) seem to work at 30-40MB/s with a MacBook Pro.
13 13  * **Known issue**: 2.4Ghz wifi performance is really bad. You probably want to disable 2.4Ghz wifi.
14 14  
15 -UPDATED 2020-12-10 the 19.07.04 builds now includes LuCi! Follow these instructions:
17 +**Images do not contain LuCi! (The build process doesn't include it for some reason I have not yet time to figure out.)** You need to have the **squashfs-sysupgrade.bin** flashed, then install LuCI. (See instructions below.)
16 16  
17 -1. Grab initramfs-factory.img from [[https:~~/~~/www.codepowered.com/openwrt/v19.07.4/bin/targets/ramips/mt7621/openwrt-ramips-mt7621-ea8100-initramfs-factory.img>>https://www.codepowered.com/openwrt/v19.07.4/bin/targets/ramips/mt7621/openwrt-ramips-mt7621-ea8100-initramfs-factory.img]] and flash it via Linksys UI.
18 -1. Wait for Openwrt to boot so that you get to LuCi at [[http:~~/~~/192.168.1.1/>>http://192.168.1.1/]]. Do NOT configure yet! It's not ready.
19 -1. Then grab squashfs-sysupgrade.bin from [[https:~~/~~/www.codepowered.com/openwrt/v19.07.4/bin/targets/ramips/mt7621/openwrt-ramips-mt7621-ea8100-squashfs-sysupgrade.bin>>https://www.codepowered.com/openwrt/v19.07.4/bin/targets/ramips/mt7621/openwrt-ramips-mt7621-ea8100-squashfs-sysupgrade.bin]] and flash it via LuCi
20 -1. Wait for it to reboot. Now you can configure!
19 +The EA8100 contains 2 firmware partitions. Using the Linksys UI will flash openwrt into only one of the 2 partitions. The booting process switches partition every few boots, so if you want to always boot into openwrt then you have to flash openwrt into both partitions.
21 21  
22 -For kernel modules, replace with this in your opkg distfeeds.conf:
21 +How to flash if your router currently has stock Linksys firmware:
23 23  
24 -{{code language="none"}}
25 -src/gz openwrt_core https://www.codepowered.com/openwrt/v19.07.4/bin/targets/ramips/mt7621/packages
26 -{{/code}}
23 +1. Download the "**openwrt-ramips-mt7621-ea8100-initramfs-kernel-factory.img**" from link above, and flash it via Linksys UI. Wait for it to start to reboot.
24 +1. Configure your computer to have IP in ##192.168.1.2/255.255.255.0##.
25 +1. Check that your router booted Openwrt by visiting [[http:~~/~~/192.168.1.1/>>http://192.168.1.1/]]. It is in Openwrt if you see a white screen with message: "The requested URL /cgi-bin/luci/ was not found on this server." (Luci is not installed currently.) Do a reboot if you see Linksys UI instead, then check again when it boots.
26 +1. Download the "**openwrt-ramips-mt7621-ea8100-squashfs-sysupgrade.bin**" from link above, and upload it into ##/tmp## in the router via SFTP. You can use [[winscp>>https://winscp.net/]] if on Windows. [[root@192.168.1.1>>mailto:root@192.168.1.1]] (No password).
27 +1. Ssh into [[root@192.168.1.1>>mailto:root@192.168.1.1]] (no password). Use [[putty>>https://www.putty.org/]] to ssh if you are on Windows.
28 +1. In the ssh shell run: ##sysupgrade /tmp/openwrt-ramips-mt7621-ea8100-squashfs-sysupgrade.bin##
29 +1. It automatically reboots after a short while. Log in via SSH again.
30 +1. Run: ##opkg update##
31 +1. Run: ##**opkg install luci**##
32 +1. Access LuCI via [[http:~~/~~/192.168.1.1/>>http://192.168.1.1/]]. You can now configure.
27 27  
28 28  If you are on my 18.x below, sysupgrading to a 19.07 image will not work. You have to manually mtd write the 19.07 "kernel-initramfs.bin" into the nand and boot/log into it (192.168.1.1), then sysupgrade.
29 29  
30 -Sysupgrade from 19.07.x to another 19.07.y will work. You can also upgrade via LuCI.
36 +Sysupgrade from 19.07.x to another 19.07.y will work. You can also upgrade via LuCI. **HOWEVER: **upgrading will wipe entire firmware partitions! Backup your files/config before sysupgrade.
31 31  
32 -{{warning}}
33 -Upgrading images will wipe entire firmware partitions! Backup your files/config before sysupgrade. It will reset router ip to 192.168.1.1.
34 -{{/warning}}
35 -
36 ---**Images do not contain LuCi! (The build process doesn't include it for some reason I have not yet time to figure out.)** You need to have the **squashfs-sysupgrade.bin** flashed, then install LuCI. (See instructions below.)--
37 -
38 ---The EA8100 contains 2 firmware partitions. Using the Linksys UI will flash openwrt into only one of the 2 partitions. The booting process switches partition every few boots, so if you want to always boot into openwrt then you have to flash openwrt into both partitions.--
39 -
40 ---How to flash if your router currently has stock Linksys firmware:--
41 -
42 -1. --Download the "**openwrt-ramips-mt7621-ea8100-initramfs-kernel-factory.img**" from link above, and flash it via Linksys UI. Wait for it to start to reboot.--
43 -1. --Configure your computer to have IP in ##192.168.1.2/255.255.255.0##.--
44 -1. --Check that your router booted Openwrt by visiting [[http:~~/~~/192.168.1.1/>>http://192.168.1.1/]]. It is in Openwrt if you see a white screen with message: "Index of /." Do a reboot if you see Linksys UI instead, then check again when it boots. --
45 -1. --Download the "**openwrt-ramips-mt7621-ea8100-squashfs-sysupgrade.bin**" from link above, and upload it into ##/tmp## in the router via SFTP. You can use [[winscp>>doc:How to WinSCP.WebHome]] if on Windows. [[root@192.168.1.1>>mailto:root@192.168.1.1]] (No password).--
46 -1. --Ssh into [[root@192.168.1.1>>mailto:root@192.168.1.1]] (no password). Use [[putty>>doc:How to Putty.WebHome]] to ssh if you are on Windows.--
47 -1. --In the ssh shell run: ##sysupgrade /tmp/openwrt-ramips-mt7621-ea8100-squashfs-sysupgrade.bin##--
48 -1. --It automatically reboots after a short while. Log in via SSH again. Check you are online by pinging 8.8.8.8 when in SSH.--
49 -1. --Run: ##opkg update##--
50 -1. --Run: ##**opkg install luci**##--
51 -1. --Access LuCI via [[http:~~/~~/192.168.1.1/>>http://192.168.1.1/]]. You can now configure.--
52 -
53 53  = 18.x =
54 54  
55 55  9bebafcb5dfe37f25285fa18fb8bfe7b68011267 (with wifi support) Download: