Wiki source code of Openwrt for Linksys EA8100

Version 31.1 by Leon Poon on 2020/09/10 14:22
Show last authors
1 switch0: port 0 = wan, port 1,2,3,4 = lan
2
3 If you brick your router you should be able to recover by soldering the UART pin headers and connecting to the serial. See [[this page for pictures>>doc:Linksys EA8100.WebHome]].
4
5
6 = 19.07.x =
7
8 19.07.4 is here!
9
10 [[https:~~/~~/www.codepowered.com/openwrt/v19.07.4/linksys_ea8100/>>https://www.codepowered.com/openwrt/v19.07.4/linksys_ea8100/]] ([[https:~~/~~/github.com/LeonPoon/openwrt/compare/v19.07.4...v19.07.4-linksys_ea8100>>https://github.com/LeonPoon/openwrt/compare/v19.07.4...v19.07.4-linksys_ea8100]])
11
12 The EA8100 contains 2 firmware partitions. Using the Linksys UI will flash openwrt into only one of the 2 partitions. The booting process switches partition every few boots, so if you want to always boot into openwrt then you have to flash openwrt into both partitions.
13
14 **Images do not contain LuCi! (The build process doesn't include it for some reason I have not yet time to figure out.)** You need to have the squashfs.bin flashed, then opkg update and opkg install luci.
15
16 How to flash if your router currently has stock Linksys firmware:
17
18 1. Flash the "**initramfs-factory.img**" via Linksys UI. Wait for it to start to reboot.
19 1. Configure your computer to have ip in 192.168.1.0/24 subnet but NOT 192.168.1.1. (so, use 192.168.1.2.) Start ping to 192.168.1.1.
20 1. Cross your fingers that the router boots openwrt. Otherwise keep rebooting until it loads the openwrt partition. (Usually 3 times max.) Wait a few minutes from reboot to let it load. If you get ping response from 192.168.1.1 it means openwrt loaded.
21 1. Scp the "**squashfs-sysupgrade.bin**" into /tmp in the router. root@192.168.1.1. No password.
22 1. Log in as root via SSH into shell. No password.
23 1. **Sysupgrade the uploaded squashfs-sysupgrade.bin**. This should flash the openwrt firmware into both firmware partitions. It auto reboots.
24 1. opkg update
25 1. **opkg install luci (the flashed images does not contain Luci)**
26 1. Access LuCI via http:~/~/192.168.1.1/. You can now configure.
27
28 If you are on my 18.x below, sysupgrading to a 19.07 image will not work. You have to manually mtd write the 19.07 "kernel-initramfs.bin" into the nand and boot/log into it (192.168.1.1), then sysupgrade.
29
30 Sysupgrade from 19.07.x to another 19.07.y will work. **HOWEVER: **sysupgrade will wipe entire firmware partitions! Backup your files/config before sysupgrade.
31
32 Since [[19.07.03>>https://www.codepowered.com/openwrt/v19.07.3/linksys_ea8100/]], as of 19.07.04:
33
34 * Wifi (5Ghz) seem to work at 30-40MB/s with a MacBook Pro.
35 * **Known issue**: 2.4Ghz wifi performance is really bad. You probably want to disable 2.4Ghz wifi.
36
37 = 18.x =
38
39 9bebafcb5dfe37f25285fa18fb8bfe7b68011267 (with wifi support) Download:
40
41 * [[initramfs-kernel.bin>>attach:openwrt-ramips-mt7621-linksys_ea8100-initramfs-kernel-9bebafcb5dfe37f25285fa18fb8bfe7b68011267.bin]]
42 * [[squashfs-sysupgrade.bin>>attach:openwrt-ramips-mt7621-linksys_ea8100-squashfs-sysupgrade-9bebafcb5dfe37f25285fa18fb8bfe7b68011267.bin]] (accepted as upgrade in factory UI)
43
44 Note that sysupgrade to a newer image is not likely to work.
45
46 (% border="1" cellpadding="0" cellspacing="0" style="margin-right:auto; width:auto" %)
47 |[[image:1567332570723-651.png]]
48
49 Dmesg:
50
51 {{code language="plain"}}
52 3: Boot system code via Flash (default).
53 4: Entr boot command line interface.
54 7: Load Boot Loader code then write to Flash via Serial.
55 9: Load Boot Loader code then write to Flash via TFTP. 4
56 You choosed 2
57 0
58
59
60 2: System Load Linux Kernel then write to Flash via TFTP.
61 Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N)
62 Please Input new ones /or Ctrl-C to discard
63 Input device IP () ==:
64 Input server IP () ==:
65 Input Linux Kernel filename (openwrt-ramips-mt7621-linksys_ea8100-initramfs-kernel.bin) ==:openwrt-ramips-mt7621-linksys_ea8100-squashfs-sysupgrade.bin
66 which kernel partition to update (1/2/3=both) (2) ==:3
67
68 NetTxPacket = 0x8FFE3200
69
70 KSEG1ADDR(NetTxPacket) = 0xAFFE3200
71
72 NetLoop,call eth_halt !
73
74 NetLoop,call eth_init !
75 Trying Eth0 (10/100-M)
76
77 Waitting for RX_DMA_BUSY status Start... done
78
79
80 ETH_STATE_ACTIVE!!
81 TFTP from server ; our IP address is
82 Filename 'openwrt-ramips-mt7621-linksys_ea8100-squashfs-sysupgrade.bin'.
83
84 TIMEOUT_COUNT=10,Load address: 0x80100000
85 Loading: Got ARP REPLY, set server/gtwy eth addr ()
86 Got it
87 #################################################################
88 #################################################################
89 #################################################################
90 #################################################################
91 #################################################################
92 #################################################################
93 #################################################################
94 #################################################################
95 #################################################################
96 #################################################################
97 #################################################################
98 #################################################################
99 #################################################################
100 #################################################################
101 #################################################################
102 #################################################################
103 #################################################################
104 ################################################
105 done
106 Bytes transferred = 5898496 (5a0100 hex)
107 LoadAddr=80100000 NetBootFileXferSize= 005a0100
108 ranand_erase: start:180000, len:20000
109 ..ranand_erase: start:1a0000, len:20000
110 ..ranand_erase: start:1c0000, len:20000
111 ...
112 .(5192)offs=7471104 piece=0 piece_size=256 rc=0
113 Done!
114 ranand_erase: start:2980000, len:20000
115 ..ranand_erase: start:29a0000, len:20000
116 ..ranand_erase: start:29c0000, len:20000
117 ...
118 .(5192)offs=49676288 piece=0 piece_size=256 rc=0
119 Done!
120 ## Booting image at bc180000 ...
121 Image Name: MIPS OpenWrt Linux-4.14.141
122 Image Type: MIPS Linux Kernel Image (lzma compressed)
123 Data Size: 2010110 Bytes = 1.9 MB
124 Load Address: 80001000
125 Entry Point: 80001000
126 ............................... Verifying Checksum ... OK
127 Uncompressing Kernel Image ... OK
128 No initrd
129 ## Transferring control to Linux (at address 80001000) ...
130 ## Giving linux memsize in MB, 256
131
132 Starting kernel ...
133
134 [ 0.000000] Linux version 4.14.141 () (gcc version 7.4.0 (OpenWrt GCC 7.4.0 r10942-9bebafcb5d)) #0 SMP Sun Sep 1 06:04:50 2019
135 [ 0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3
136 [ 0.000000] bootconsole [early0] enabled
137 [ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
138 [ 0.000000] MIPS: machine is Linksys EA8100
139 [ 0.000000] Determined physical RAM map:
140 [ 0.000000] memory: 10000000 @ 00000000 (usable)
141 [ 0.000000] Initrd not found or empty - disabling initrd
142 [ 0.000000] VPE topology {2,2} total 4
143 [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
144 [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
145 [ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
146 [ 0.000000] Zone ranges:
147 [ 0.000000] Normal [mem 0x0000000000000000-0x000000000fffffff]
148 [ 0.000000] HighMem empty
149 [ 0.000000] Movable zone start for each node
150 [ 0.000000] Early memory node ranges
151 [ 0.000000] node 0: [mem 0x0000000000000000-0x000000000fffffff]
152 [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff]
153 [ 0.000000] random: get_random_bytes called from start_kernel+0x9c/0x4d8 with crng_init=0
154 [ 0.000000] percpu: Embedded 14 pages/cpu s26064 r8192 d23088 u57344
155 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 64960
156 [ 0.000000] Kernel command line: console=ttyS0,115200n8 rootfstype=squashfs,jffs2
157 [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
158 [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
159 [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
160 [ 0.000000] Writing ErrCtl register=0002c420
161 [ 0.000000] Readback ErrCtl register=0002c420
162 [ 0.000000] Memory: 251700K/262144K available (4796K kernel code, 251K rwdata, 1040K rodata, 1260K init, 254K bss, 10444K reserved, 0K cma-reserved, 0K highmem)
163 [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
164 [ 0.000000] Hierarchical RCU implementation.
165 [ 0.000000] NR_IRQS: 256
166 [ 0.000000] CPU Clock: 880MHz
167 [ 0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns
168 [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4343773742 ns
169 [ 0.000009] sched_clock: 32 bits at 440MHz, resolution 2ns, wraps every 4880645118ns
170 [ 0.007802] Calibrating delay loop... 586.13 BogoMIPS (lpj=2930688)
171 [ 0.073969] pid_max: default: 32768 minimum: 301
172 [ 0.078775] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
173 [ 0.085284] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
174 [ 0.094340] Hierarchical SRCU implementation.
175 [ 0.099495] smp: Bringing up secondary CPUs ...
176 [ 0.114811] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
177 [ 0.114820] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
178 [ 0.114831] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
179 [ 0.114963] CPU1 revision is: 0001992f (MIPS 1004Kc)
180 [ 0.164211] Synchronize counters for CPU 1: done.
181 [ 0.208189] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
182 [ 0.208197] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
183 [ 0.208206] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
184 [ 0.208284] CPU2 revision is: 0001992f (MIPS 1004Kc)
185 [ 0.255179] Synchronize counters for CPU 2: done.
186 [ 0.295789] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
187 [ 0.295797] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
188 [ 0.295805] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
189 [ 0.295885] CPU3 revision is: 0001992f (MIPS 1004Kc)
190 [ 0.340367] Synchronize counters for CPU 3: done.
191 [ 0.370232] smp: Brought up 1 node, 4 CPUs
192 [ 0.378204] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
193 [ 0.388001] futex hash table entries: 1024 (order: 3, 32768 bytes)
194 [ 0.394408] pinctrl core: initialized pinctrl subsystem
195 [ 0.401009] NET: Registered protocol family 16
196 [ 0.415266] pull PCIe RST: RALINK_RSTCTRL = 4000000
197 [ 0.720548] release PCIe RST: RALINK_RSTCTRL = 7000000
198 [ 0.725598] ***** Xtal 40MHz *****
199 [ 0.728952] release PCIe RST: RALINK_RSTCTRL = 7000000
200 [ 0.734049] Port 0 N_FTS = 1b102800
201 [ 0.737517] Port 1 N_FTS = 1b102800
202 [ 0.740963] Port 2 N_FTS = 1b102800
203 [ 1.896358] PCIE2 no card, disable it(RST&CLK)
204 [ 1.900719] -> 21007f2
205 [ 1.903123] PCIE0 enabled
206 [ 1.905712] PCIE1 enabled
207 [ 1.908316] PCI host bridge /pcie@1e140000 ranges:
208 [ 1.913096] MEM 0x0000000060000000..0x000000006fffffff
209 [ 1.918245] IO 0x000000001e160000..0x000000001e16ffff
210 [ 1.923451] PCI coherence region base: 0xbfbf8000, mask/settings: 0x60000000
211 [ 1.939415] mt7621_gpio 1e000600.gpio: registering 32 gpios
212 [ 1.945254] mt7621_gpio 1e000600.gpio: registering 32 gpios
213 [ 1.950961] mt7621_gpio 1e000600.gpio: registering 32 gpios
214 [ 1.958178] PCI host bridge to bus 0000:00
215 [ 1.962213] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
216 [ 1.969068] pci_bus 0000:00: root bus resource [io 0xffffffff]
217 [ 1.974896] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
218 [ 1.981655] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
219 [ 1.990318] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
220 [ 1.998262] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
221 [ 2.007510] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
222 [ 2.014070] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
223 [ 2.020937] pci 0000:00:01.0: BAR 0: no space for [mem size 0x80000000]
224 [ 2.027521] pci 0000:00:01.0: BAR 0: failed to assign [mem size 0x80000000]
225 [ 2.034415] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
226 [ 2.041173] pci 0000:00:01.0: BAR 8: assigned [mem 0x60100000-0x601fffff]
227 [ 2.047897] pci 0000:00:00.0: BAR 1: assigned [mem 0x60200000-0x6020ffff]
228 [ 2.054657] pci 0000:00:01.0: BAR 1: assigned [mem 0x60210000-0x6021ffff]
229 [ 2.061377] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit]
230 [ 2.068661] pci 0000:00:00.0: PCI bridge to [bus 01]
231 [ 2.073551] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff]
232 [ 2.080327] pci 0000:02:00.0: BAR 0: assigned [mem 0x60100000-0x601fffff 64bit]
233 [ 2.087559] pci 0000:00:01.0: PCI bridge to [bus 02]
234 [ 2.092502] pci 0000:00:01.0: bridge window [mem 0x60100000-0x601fffff]
235 [ 2.100582] clocksource: Switched to clocksource GIC
236 [ 2.107275] NET: Registered protocol family 2
237 [ 2.112196] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
238 [ 2.119081] TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
239 [ 2.125539] TCP: Hash tables configured (established 2048 bind 2048)
240 [ 2.131955] UDP hash table entries: 256 (order: 1, 8192 bytes)
241 [ 2.137713] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
242 [ 2.144212] NET: Registered protocol family 1
243 [ 2.380532] 4 CPUs re-calibrate udelay(lpj = 2924544)
244 [ 2.387039] Crashlog allocated RAM at address 0x3f00000
245 [ 2.392460] workingset: timestamp_bits=14 max_order=16 bucket_order=2
246 [ 2.408000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
247 [ 2.413806] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
248 [ 2.425815] random: fast init done
249 [ 2.430745] io scheduler noop registered
250 [ 2.434579] io scheduler deadline registered (default)
251 [ 2.440747] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled
252 [ 2.448257] console [ttyS0] disabled
253 [ 2.451855] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 19, base_baud = 3125000) is a 16550A
254 [ 2.460836] console [ttyS0] enabled
255 [ 2.460836] console [ttyS0] enabled
256 [ 2.467691] bootconsole [early0] disabled
257 [ 2.467691] bootconsole [early0] disabled
258 [ 2.477567] MediaTek Nand driver init, version v2.1 Fix AHB virt2phys error
259 [ 2.484816] Enable NFI Clock
260 [ 2.487689] # MTK NAND # : Use HW ECC
261 [ 2.491382] Device not found, ID: c2f1
262 [ 2.495110] Not Support this Device!
263 [ 2.498835] chip_mode=00000001
264 [ 2.501893] Support this Device in MTK table! c2f1
265 [ 2.506840] [NAND]select ecc bit:4, sparesize :64 spare_per_sector=16
266 [ 2.513320] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xf1
267 [ 2.519642] nand: Macronix NAND 128MiB 3,3V 8-bit
268 [ 2.524347] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
269 [ 2.531927] Scanning device for bad blocks
270 [ 2.819771] 7 fixed-partitions partitions found on MTD device MT7621-NAND
271 [ 2.826546] Creating 7 MTD partitions on "MT7621-NAND":
272 [ 2.831774] 0x000000000000-0x000000080000 : "uboot"
273 [ 2.837706] 0x000000080000-0x0000000c0000 : "uboot_env"
274 [ 2.843891] 0x0000000c0000-0x000000100000 : "factory"
275 [ 2.849892] 0x000000100000-0x000000140000 : "s_env"
276 [ 2.855720] 0x000000140000-0x000000180000 : "devinfo"
277 [ 2.861732] 0x000000180000-0x000002980000 : "firmware1"
278 [ 2.870032] 0x000002980000-0x000005180000 : "firmware2"
279 [ 2.877154] 1 uboot-env-boot_part partitions found on MTD device firmware2
280 [ 2.884061] 0x000002980000-0x000005180000 : "firmware"
281 [ 3.438509] 2 uimage-fw partitions found on MTD device firmware
282 [ 3.444473] 0x000002980000-0x000002b80000 : "kernel"
283 [ 3.450603] 0x000002b80000-0x000005180000 : "ubi"
284 [ 3.456742] [mtk_nand] probe successfully!
285 [ 3.461570] Signature matched and data read!
286 [ 3.465818] load_fact_bbt success 1023
287 [ 3.470276] libphy: Fixed MDIO Bus: probed
288 [ 3.542951] mtd_read_prop_mac: find prop "hw_mac_addr" in devinfo(max 0x40000) from 0x0
289 [ 3.550970] mtd_read_prop_mac: hw_mac_addr=
290 [ 3.556774] libphy: mdio: probed
291 [ 4.961009] mtk_soc_eth 1e100000.ethernet: loaded mt7530 driver
292 [ 4.967662] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 21
293 [ 4.978262] NET: Registered protocol family 10
294 [ 4.984286] Segment Routing with IPv6
295 [ 4.988020] NET: Registered protocol family 17
296 [ 4.992556] 8021q: 802.1Q VLAN Support v1.8
297 [ 4.999621] UBI: auto-attach mtd9
298 [ 5.003015] ubi0: attaching mtd9
299 [ 5.033798] UBI: EOF marker found, PEBs from 25 will be erased
300 [ 5.039967] ubi0: scanning is finished
301 [ 5.081872] ubi0: volume 1 ("rootfs_data") re-sized from 9 to 258 LEBs
302 [ 5.089203] ubi0: attached mtd9 (name "ubi", size 38 MiB)
303 [ 5.094644] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
304 [ 5.101543] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
305 [ 5.108298] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
306 [ 5.115245] ubi0: good PEBs: 297, bad PEBs: 7, corrupted PEBs: 0
307 [ 5.121247] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
308 [ 5.128436] ubi0: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number:
309 [ 5.137541] ubi0: available PEBs: 0, total reserved PEBs: 297, PEBs reserved for bad PEB handling: 13
310 [ 5.146764] ubi0: background thread "ubi_bgt0d" started, PID 378
311 [ 5.148847] block ubiblock0_0: created from ubi0:0(rootfs)
312 [ 5.158262] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem
313 [ 5.165234] hctosys: unable to open rtc device (rtc0)
314 [ 5.183831] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
315 [ 5.195491] Freeing unused kernel memory: 1260K
316 [ 5.200022] This architecture does not have kernel memory protection.
317 [ 5.783744] init: Console is alive
318 [ 5.787378] init: - watchdog -
319 [ 6.295000] mtk_soc_eth 1e100000.ethernet eth0: port 1 link up
320 [ 6.502425] kmodloader: loading kernel modules from /etc/modules-boot.d/*
321 [ 6.591413] usbcore: registered new interface driver usbfs
322 [ 6.596966] usbcore: registered new interface driver hub
323 [ 6.602453] usbcore: registered new device driver usb
324 [ 6.615285] SCSI subsystem initialized
325 [ 6.626976] xhci-mtk 1e1c0000.xhci: 1e1c0000.xhci supply vbus not found, using dummy regulator
326 [ 6.635689] xhci-mtk 1e1c0000.xhci: 1e1c0000.xhci supply vusb33 not found, using dummy regulator
327 [ 6.644627] xhci-mtk 1e1c0000.xhci: xHCI Host Controller
328 [ 6.649947] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 1
329 [ 6.660739] xhci-mtk 1e1c0000.xhci: hcc params 0x01401198 hci version 0x96 quirks 0x0000000000210010
330 [ 6.669906] xhci-mtk 1e1c0000.xhci: irq 20, io mem 0x1e1c0000
331 [ 6.676639] hub 1-0:1.0: USB hub found
332 [ 6.680467] hub 1-0:1.0: 2 ports detected
333 [ 6.685052] xhci-mtk 1e1c0000.xhci: xHCI Host Controller
334 [ 6.690366] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 2
335 [ 6.697886] xhci-mtk 1e1c0000.xhci: Host supports USB 3.0 SuperSpeed
336 [ 6.704507] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
337 [ 6.713446] hub 2-0:1.0: USB hub found
338 [ 6.717275] hub 2-0:1.0: 1 port detected
339 [ 6.727313] usbcore: registered new interface driver usb-storage
340 [ 6.733578] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
341 [ 6.750877] init: - preinit -
342 [ 7.180814] usb 2-1: new SuperSpeed USB device number 2 using xhci-mtk
343 [ 7.212805] random: procd: uninitialized urandom read (4 bytes read)
344 [ 7.212971] usb-storage 2-1:1.0: USB Mass Storage device detected
345 [ 7.225920] scsi host0: usb-storage 2-1:1.0
346 [ 7.366240] mtk_soc_eth 1e100000.ethernet: PPE started
347 Press the [f] key and hit [enter] to enter failsafe mode
348 Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
349 [ 10.582466] UBIFS (ubi0:1): default file-system created
350 [ 10.589130] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 496
351 [ 10.700430] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
352 [ 10.708276] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
353 [ 10.718161] UBIFS (ubi0:1): FS size: 31490048 bytes (30 MiB, 248 LEBs), journal size 1523712 bytes (1 MiB, 12 LEBs)
354 [ 10.728565] UBIFS (ubi0:1): reserved for root: 1487352 bytes (1452 KiB)
355 [ 10.735166] UBIFS (ubi0:1): media format: w4/r0 (latest is w5/r0), UUID , small LPT model
356 [ 10.749347] mount_root: overlay filesystem has not been fully initialized yet
357 [ 10.756981] mount_root: switching to ubifs overlay
358 [ 10.781065] urandom-seed: Seed file not found (/etc/urandom.seed)
359 [ 10.861172] mtk_soc_eth 1e100000.ethernet: 0x100 = 0x6060000c, 0x10c = 0x80818
360 [ 10.876085] procd: - early -
361 [ 10.879061] procd: - watchdog -
362 [ 11.550737] procd: - watchdog -
363 [ 11.554202] procd: - ubus -
364 [ 11.583502] random: ubusd: uninitialized urandom read (4 bytes read)
365 [ 11.611421] random: ubusd: uninitialized urandom read (4 bytes read)
366 [ 11.618117] random: ubusd: uninitialized urandom read (4 bytes read)
367 [ 11.625387] procd: - init -
368 Please press Enter to activate this console.
369 [ 12.046531] kmodloader: loading kernel modules from /etc/modules.d/*
370 [ 12.057746] ip6_tables: (C) 2000-2006 Netfilter Core Team
371 [ 12.069204] Loading modules backported from Linux version v5.3-rc4-0-gd45331b00ddb
372 [ 12.076775] Backport generated by backports.git v5.3-rc4-1-0-g4ec72687
373 [ 12.085114] ip_tables: (C) 2000-2006 Netfilter Core Team
374 [ 12.096731] nf_conntrack version 0.5.0 (4096 buckets, 16384 max)
375 [ 12.127574] urngd: v1.0.0 started.
376 [ 12.145053] xt_time: kernel timezone is -0000
377 [ 12.214244] bus=0x1, slot = 0x0, irq=0x0
378 [ 12.218201] PCI: Enabling device 0000:00:00.0 (0004 -> 0006)
379 [ 12.241178] mt7615e 0000:01:00.0: HW/SW Version: 0x8a108a10, Build Time: 20180518100604a
380 [ 12.241178]
381 [ 12.266469] random: crng init done
382 [ 12.269877] random: 6 urandom warning(s) missed due to ratelimiting
383 [ 12.456236] mt7615e 0000:01:00.0: N9 Firmware Version: _reserved_, Build Time: 20190103180756
384 [ 12.471995] mt7615e 0000:01:00.0: CR4 Firmware Version: _reserved_, Build Time: 20181207140436
385 +ýýrýýýýýýýbus=0x2, slot = 0x1, irq=0x0
386 [ 20.131310] PCI: Enabling device 0000:00:01.0 (0004 -> 0006)
387 [ 20.161193] mt7615e 0000:02:00.0: HW/SW Version: 0x8a108a10, Build Time: 20180518100604a
388 [ 20.161193]
389 [ 20.185604] mt7615e 0000:02:00.0: N9 Firmware Version: _reserved_, Build Time: 20190103180756
390 [ 20.200746] mt7615e 0000:02:00.0: CR4 Firmware Version: _reserved_, Build Time: 20181207140436
391 [ 27.852570] PPP generic driver version 2.4.2
392 [ 27.858358] NET: Registered protocol family 24
393 [ 27.866716] kmodloader: done loading kernel modules from /etc/modules.d/*
394 [ 41.276638] mtk_soc_eth 1e100000.ethernet: PPE started
395 [ 41.287935] br-lan: port 1(eth0.2) entered blocking state
396 [ 41.293420] br-lan: port 1(eth0.2) entered disabled state
397 [ 41.299522] device eth0.2 entered promiscuous mode
398 [ 41.304484] device eth0 entered promiscuous mode
399 [ 41.311947] br-lan: port 1(eth0.2) entered blocking state
400 [ 41.317384] br-lan: port 1(eth0.2) entered forwarding state
401 [ 41.323511] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
402 [ 42.321086] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
403
404
405
406 BusyBox v1.31.0 () built-in shell (ash)
407
408 _______ ________ __
409 | |.-----.-----.-----.| | | |.----.| |_
410 | - || _ | -__| || | | || _|| _|
411 |_______|| __|_____|__|__||________||__| |____|
412 |__| W I R E L E S S F R E E D O M
413 -----------------------------------------------------
414 OpenWrt SNAPSHOT, r10942-9bebafcb5d
415 -----------------------------------------------------
416 === WARNING! =====================================
417 There is no root password defined on this device!
418 Use the "passwd" command to set up a new password
419 in order to prevent unauthorized SSH logins.
420 --------------------------------------------------
421 root@OpenWrt:/# ifconfig -a
422 br-lan Link encap:Ethernet HWaddr
423 inet addr:192.168.1.1 Bcast:192.168.1.255 Mask:255.255.255.0
424 inet6 addr: fde0:62db:5134::1/60 Scope:Global
425 inet6 addr: fe80::/64 Scope:Link
426 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
427 RX packets:41 errors:0 dropped:0 overruns:0 frame:0
428 TX packets:13 errors:0 dropped:0 overruns:0 carrier:0
429 collisions:0 txqueuelen:1000
430 RX bytes:8012 (7.8 KiB) TX bytes:2126 (2.0 KiB)
431
432 eth0 Link encap:Ethernet HWaddr
433 inet6 addr: fe80::/64 Scope:Link
434 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
435 RX packets:102 errors:0 dropped:0 overruns:0 frame:0
436 TX packets:47 errors:0 dropped:0 overruns:0 carrier:0
437 collisions:0 txqueuelen:1000
438 RX bytes:19418 (18.9 KiB) TX bytes:8199 (8.0 KiB)
439 Interrupt:21
440
441 eth0.1 Link encap:Ethernet HWaddr
442 inet6 addr: fe80::/64 Scope:Link
443 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
444 RX packets:0 errors:0 dropped:0 overruns:0 frame:0
445 TX packets:20 errors:0 dropped:0 overruns:0 carrier:0
446 collisions:0 txqueuelen:1000
447 RX bytes:0 (0.0 B) TX bytes:3368 (3.2 KiB)
448
449 eth0.2 Link encap:Ethernet HWaddr
450 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
451 RX packets:41 errors:0 dropped:0 overruns:0 frame:0
452 TX packets:13 errors:0 dropped:0 overruns:0 carrier:0
453 collisions:0 txqueuelen:1000
454 RX bytes:8012 (7.8 KiB) TX bytes:2126 (2.0 KiB)
455
456 lo Link encap:Local Loopback
457 inet addr:127.0.0.1 Mask:255.0.0.0
458 inet6 addr: ::1/128 Scope:Host
459 UP LOOPBACK RUNNING MTU:65536 Metric:1
460 RX packets:28 errors:0 dropped:0 overruns:0 frame:0
461 TX packets:28 errors:0 dropped:0 overruns:0 carrier:0
462 collisions:0 txqueuelen:1000
463 RX bytes:1904 (1.8 KiB) TX bytes:1904 (1.8 KiB)
464
465 wlan0 Link encap:Ethernet HWaddr
466 BROADCAST MULTICAST MTU:1500 Metric:1
467 RX packets:0 errors:0 dropped:0 overruns:0 frame:0
468 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
469 collisions:0 txqueuelen:1000
470 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
471
472 wlan1 Link encap:Ethernet HWaddr
473 BROADCAST MULTICAST MTU:1500 Metric:1
474 RX packets:0 errors:0 dropped:0 overruns:0 frame:0
475 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
476 collisions:0 txqueuelen:1000
477 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
478
479 root@OpenWrt:/# ls -l
480 drwxr-xr-x 2 root root 778 Sep 1 06:04 bin
481 drwxr-xr-x 4 root root 1300 Sep 1 06:05 dev
482 drwxr-xr-x 1 root root 512 Sep 1 06:05 etc
483 -rwxr-xr-x 1 root root 78 Dec 30 2018 init
484 drwxr-xr-x 11 root root 426 Sep 1 06:04 lib
485 drwxr-xr-x 2 root root 3 Sep 1 06:04 mnt
486 drwxr-xr-x 4 root root 360 Sep 1 06:05 overlay
487 dr-xr-xr-x 73 root root 0 Jan 1 1970 proc
488 drwxr-xr-x 16 root root 223 Sep 1 06:04 rom
489 drwxr-xr-x 2 root root 3 Sep 1 06:04 root
490 drwxr-xr-x 2 root root 822 Sep 1 06:04 sbin
491 dr-xr-xr-x 11 root root 0 Jan 1 1970 sys
492 drwxrwxrwt 15 root root 380 Sep 1 06:05 tmp
493 drwxr-xr-x 7 root root 89 Sep 1 06:04 usr
494 lrwxrwxrwx 1 root root 3 Sep 1 06:04 var -> tmp
495 drwxr-xr-x 2 root root 3 Sep 1 06:04 www
496 root@OpenWrt:/# ps
497 PID USER VSZ STAT COMMAND
498 1 root 1576 S /sbin/procd
499 2 root 0 SW [kthreadd]
500 3 root 0 IW [kworker/0:0]
501 4 root 0 IW< [kworker/0:0H]
502 5 root 0 IW [kworker/u8:0]
503 6 root 0 IW< [mm_percpu_wq]
504 7 root 0 SW [ksoftirqd/0]
505 8 root 0 IW [rcu_sched]
506 9 root 0 IW [rcu_bh]
507 10 root 0 SW [migration/0]
508 11 root 0 SW [cpuhp/0]
509 12 root 0 SW [cpuhp/1]
510 13 root 0 SW [migration/1]
511 14 root 0 SW [ksoftirqd/1]
512 16 root 0 IW< [kworker/1:0H]
513 17 root 0 SW [cpuhp/2]
514 18 root 0 SW [migration/2]
515 19 root 0 SW [ksoftirqd/2]
516 21 root 0 IW< [kworker/2:0H]
517 22 root 0 SW [cpuhp/3]
518 23 root 0 SW [migration/3]
519 24 root 0 SW [ksoftirqd/3]
520 25 root 0 IW [kworker/3:0]
521 26 root 0 IW< [kworker/3:0H]
522 27 root 0 IW< [netns]
523 41 root 0 IW [kworker/u8:3]
524 68 root 0 IW [kworker/3:1]
525 69 root 0 IW [kworker/2:1]
526 138 root 0 IW [kworker/1:1]
527 139 root 0 SW [oom_reaper]
528 140 root 0 IW< [writeback]
529 142 root 0 SW [kcompactd0]
530 143 root 0 IW< [crypto]
531 145 root 0 IW< [kblockd]
532 175 root 0 IW< [watchdogd]
533 199 root 0 SW [kswapd0]
534 268 root 0 IW< [pencrypt]
535 270 root 0 IW< [pdecrypt]
536 366 root 0 IW< [ipv6_addrconf]
537 378 root 0 SW [ubi_bgt0d]
538 383 root 0 IW< [kworker/0:1H]
539 384 root 0 IW< [kworker/2:1H]
540 385 root 0 IW [kworker/2:2]
541 386 root 0 IW< [kworker/3:1H]
542 389 root 0 IW< [kworker/1:1H]
543 429 root 0 IW [kworker/0:2]
544 437 root 0 IW [kworker/1:2]
545 453 root 0 SW [scsi_eh_0]
546 454 root 0 IW< [scsi_tmf_0]
547 455 root 0 SW [usb-storage]
548 496 root 0 SW [ubifs_bgt0_1]
549 573 root 1220 S /sbin/ubusd
550 574 root 1220 S /bin/ash --login
551 591 root 1028 S /sbin/urngd
552 660 root 0 IW< [cfg80211]
553 1012 root 1248 S /sbin/logd -S 64
554 1074 dnsmasq 1344 S /usr/sbin/dnsmasq -C /var/etc/dnsmasq.conf.cfg01411c
555 1111 root 1080 S /usr/sbin/dropbear -F -P /var/run/dropbear.1.pid -p
556 1168 root 1700 S /sbin/netifd
557 1204 root 1448 S /usr/sbin/odhcpd
558 1360 root 1212 S udhcpc -p /var/run/udhcpc-eth0.1.pid -s /lib/netifd/
559 1361 root 1052 S odhcp6c -s /lib/netifd/dhcpv6.script -P0 -t120 eth0.
560 1391 root 1212 S< /usr/sbin/ntpd -n -N -S /usr/sbin/ntpd-hotplug -p 0.
561 1720 root 1212 R ps
562 root@OpenWrt:/etc# ping www.google.co
563 PING www.google.co (): 56 data bytes
564 64 bytes from : seq=0 ttl=52 time=4.718 ms
565 ^C
566 --- www.google.co ping statistics ---
567 1 packets transmitted, 1 packets received, 0% packet loss
568 round-trip min/avg/max = 4.718/4.718/4.718 ms
569 root@OpenWrt:/etc# ping www.google.com
570 PING www.google.com (): 56 data bytes
571 64 bytes from : seq=0 ttl=47 time=4.927 ms
572 64 bytes from : seq=1 ttl=47 time=4.687 ms
573 ^C
574 --- www.google.com ping statistics ---
575 2 packets transmitted, 2 packets received, 0% packet loss
576 round-trip min/avg/max = 4.687/4.807/4.927 ms
577 root@OpenWrt:/etc# opkg update
578 Downloading http://downloads.openwrt.org/snapshots/targets/ramips/mt7621/packages/Packages.gz
579 Updated list of available packages in /var/opkg-lists/openwrt_core
580 Downloading http://downloads.openwrt.org/snapshots/targets/ramips/mt7621/packages/Packages.sig
581 Signature check passed.
582 Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/base/Packages.gz
583 Updated list of available packages in /var/opkg-lists/openwrt_base
584 Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/base/Packages.sig
585 Signature check passed.
586 Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/Packages.gz
587 Updated list of available packages in /var/opkg-lists/openwrt_luci
588 Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/Packages.sig
589 Signature check passed.
590 Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/packages/Packages.gz
591 Updated list of available packages in /var/opkg-lists/openwrt_packages
592 Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/packages/Packages.sig
593 Signature check passed.
594 Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/routing/Packages.gz
595 Updated list of available packages in /var/opkg-lists/openwrt_routing
596 Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/routing/Packages.sig
597 Signature check passed.
598 Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/telephony/Packages.gz
599 Updated list of available packages in /var/opkg-lists/openwrt_telephony
600 Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/telephony/Packages.sig
601 Signature check passed.
602 root@OpenWrt:/etc# opkg install luci
603 Installing luci (git-19.241.65047-dffe9ca-1) to root...
604 Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/luci_git-19.241.65047-dffe9ca-1_all.ipk
605 Installing uhttpd (2019-08-17-6b03f960-3) to root...
606 Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/base/uhttpd_2019-08-17-6b03f960-3_mipsel_24kc.ipk
607 Installing liblua5.1.5 (5.1.5-5) to root...
608 Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/base/liblua5.1.5_5.1.5-5_mipsel_24kc.ipk
609 Installing lua (5.1.5-5) to root...
610 Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/base/lua_5.1.5-5_mipsel_24kc.ipk
611 Installing luci-lib-nixio (git-19.241.65047-dffe9ca-1) to root...
612 Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/luci-lib-nixio_git-19.241.65047-dffe9ca-1_mipsel_24kc.ipk
613 Installing luci-lib-ip (git-19.241.65047-dffe9ca-1) to root...
614 Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/luci-lib-ip_git-19.241.65047-dffe9ca-1_mipsel_24kc.ipk
615 Installing rpcd (2019-06-05-89bfaa42-3) to root...
616 Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/base/rpcd_2019-06-05-89bfaa42-3_mipsel_24kc.ipk
617 Installing libubus-lua (2018-10-06-221ce7e7-1) to root...
618 Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/base/libubus-lua_2018-10-06-221ce7e7-1_mipsel_24kc.ipk
619 Installing luci-lib-jsonc (git-19.241.65047-dffe9ca-1) to root...
620 Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/luci-lib-jsonc_git-19.241.65047-dffe9ca-1_mipsel_24kc.ipk
621 Installing liblucihttp0 (2019-07-05-a34a17d5-1) to root...
622 Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/liblucihttp0_2019-07-05-a34a17d5-1_mipsel_24kc.ipk
623 Installing liblucihttp-lua (2019-07-05-a34a17d5-1) to root...
624 Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/liblucihttp-lua_2019-07-05-a34a17d5-1_mipsel_24kc.ipk
625 Installing luci-base (git-19.241.65047-dffe9ca-1) to root...
626 Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/luci-base_git-19.241.65047-dffe9ca-1_mipsel_24kc.ipk
627 Installing libiwinfo-lua (2019-08-28-a9f95570-1) to root...
628 Downloading http://downloads.openwrt.org/snapshots/targets/ramips/mt7621/packages/libiwinfo-lua_2019-08-28-a9f95570-1_mipsel_24kc.ipk
629 Installing luci-mod-status (git-19.241.65047-dffe9ca-1) to root...
630 Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/luci-mod-status_git-19.241.65047-dffe9ca-1_mipsel_24kc.ipk
631 Installing luci-mod-system (git-19.241.65047-dffe9ca-1) to root...
632 Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/luci-mod-system_git-19.241.65047-dffe9ca-1_all.ipk
633 Installing luci-mod-network (git-19.241.65047-dffe9ca-1) to root...
634 Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/luci-mod-network_git-19.241.65047-dffe9ca-1_all.ipk
635 Installing luci-mod-admin-full (git-19.241.65047-dffe9ca-1) to root...
636 Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/luci-mod-admin-full_git-19.241.65047-dffe9ca-1_all.ipk
637 Installing luci-theme-bootstrap (git-19.241.65047-dffe9ca-1) to root...
638 Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/luci-theme-bootstrap_git-19.241.65047-dffe9ca-1_all.ipk
639 Installing luci-app-firewall (git-19.241.65047-dffe9ca-1) to root...
640 Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/luci-app-firewall_git-19.241.65047-dffe9ca-1_all.ipk
641 Installing luci-app-opkg (git-19.241.65047-dffe9ca-1) to root...
642 Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/luci-app-opkg_git-19.241.65047-dffe9ca-1_all.ipk
643 Installing luci-proto-ppp (git-19.241.65047-dffe9ca-1) to root...
644 Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/luci-proto-ppp_git-19.241.65047-dffe9ca-1_all.ipk
645 Installing luci-proto-ipv6 (git-19.241.65047-dffe9ca-1) to root...
646 Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/luci-proto-ipv6_git-19.241.65047-dffe9ca-1_all.ipk
647 Installing rpcd-mod-rrdns (20170710) to root...
648 Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/rpcd-mod-rrdns_20170710_mipsel_24kc.ipk
649 Configuring liblucihttp0.
650 Configuring luci-app-opkg.
651 Configuring rpcd.
652 Configuring liblua5.1.5.
653 Configuring luci-lib-ip.
654 Configuring libubus-lua.
655 Configuring libiwinfo-lua.
656 Configuring lua.
657 Configuring luci-lib-nixio.
658 Configuring luci-lib-jsonc.
659 Configuring liblucihttp-lua.
660 Configuring luci-base.
661 Configuring luci-mod-system.
662 Configuring luci-theme-bootstrap.
663 Configuring luci-mod-status.
664 Configuring luci-app-firewall.
665 Configuring luci-proto-ppp.
666 Configuring luci-mod-network.
667 Configuring luci-mod-admin-full.
668 Configuring luci-proto-ipv6.
669 Configuring uhttpd.
670 Configuring rpcd-mod-rrdns.
671 Configuring luci.
672 root@OpenWrt:/etc# df -h
673 Filesystem Size Used Available Use% Mounted on
674 /dev/root 2.8M 2.8M 0 100% /rom
675 tmpfs 123.5M 764.0K 122.8M 1% /tmp
676 /dev/ubi0_1 27.1M 1.4M 24.3M 5% /overlay
677 overlayfs:/overlay 27.1M 1.4M 24.3M 5% /
678 tmpfs 512.0K 0 512.0K 0% /dev
679 root@OpenWrt:/etc# [ 2075.963720] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
680 [ 2075.973245] br-lan: port 2(wlan0) entered blocking state
681 [ 2075.978551] br-lan: port 2(wlan0) entered disabled state
682 [ 2075.984368] device wlan0 entered promiscuous mode
683 [ 2087.165173] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
684 [ 2087.171890] br-lan: port 2(wlan0) entered blocking state
685 [ 2087.177194] br-lan: port 2(wlan0) entered forwarding state
686 [ 2096.494533] device wlan0 left promiscuous mode
687 [ 2096.499322] br-lan: port 2(wlan0) entered disabled state
688 [ 2097.382887] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
689 [ 2097.393568] br-lan: port 2(wlan0) entered blocking state
690 [ 2097.398924] br-lan: port 2(wlan0) entered disabled state
691 [ 2097.404922] device wlan0 entered promiscuous mode
692 [ 2097.409972] br-lan: port 2(wlan0) entered blocking state
693 [ 2097.415296] br-lan: port 2(wlan0) entered forwarding state
694 [ 2097.749351] br-lan: port 2(wlan0) entered disabled state
695 [ 2107.953875] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
696 [ 2107.960561] br-lan: port 2(wlan0) entered blocking state
697 [ 2107.965861] br-lan: port 2(wlan0) entered forwarding state
698 [ 2117.964353] device wlan0 left promiscuous mode
699 [ 2117.969130] br-lan: port 2(wlan0) entered disabled state
700 [ 2118.782586] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
701 [ 2118.792816] br-lan: port 2(wlan0) entered blocking state
702 [ 2118.798173] br-lan: port 2(wlan0) entered disabled state
703 [ 2118.804171] device wlan0 entered promiscuous mode
704 [ 2118.809362] br-lan: port 2(wlan0) entered blocking state
705 [ 2118.814692] br-lan: port 2(wlan0) entered forwarding state
706 [ 2119.189273] br-lan: port 2(wlan0) entered disabled state
707 [ 2130.258107] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
708 [ 2130.264811] br-lan: port 2(wlan0) entered blocking state
709 [ 2130.270163] br-lan: port 2(wlan0) entered forwarding state
710 [ 2245.748473] device wlan0 left promiscuous mode
711 [ 2245.753145] br-lan: port 2(wlan0) entered disabled state
712 [ 2246.536062] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
713 [ 2246.546273] br-lan: port 2(wlan0) entered blocking state
714 [ 2246.551680] br-lan: port 2(wlan0) entered disabled state
715 [ 2246.557667] device wlan0 entered promiscuous mode
716 [ 2246.562855] br-lan: port 2(wlan0) entered blocking state
717 [ 2246.568267] br-lan: port 2(wlan0) entered forwarding state
718 [ 2246.838430] br-lan: port 2(wlan0) entered disabled state
719 [ 2246.948147] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
720 [ 2246.954850] br-lan: port 2(wlan1) entered blocking state
721 [ 2246.960197] br-lan: port 2(wlan1) entered forwarding state
722
723 root@OpenWrt:/etc#
724 root@OpenWrt:/etc# uci show wireless
725 wireless.radio0=wifi-device
726 wireless.radio0.type='mac80211'
727 wireless.radio0.channel='11'
728 wireless.radio0.hwmode='11g'
729 wireless.radio0.path='pci0000:00/0000:00:00.0/0000:01:00.0'
730 wireless.radio0.country='00'
731 wireless.radio0.legacy_rates='1'
732 wireless.radio0.htmode='HT20'
733 wireless.default_radio0=wifi-iface
734 wireless.default_radio0.device='radio0'
735 wireless.default_radio0.network='lan'
736 wireless.default_radio0.mode='ap'
737 wireless.default_radio0.encryption='psk2'
738 wireless.default_radio0.key='qwerty1234'
739 wireless.default_radio0.ssid='asdf'
740 wireless.radio1=wifi-device
741 wireless.radio1.type='mac80211'
742 wireless.radio1.channel='36'
743 wireless.radio1.hwmode='11a'
744 wireless.radio1.path='pci0000:00/0000:00:01.0/0000:02:00.0'
745 wireless.radio1.htmode='VHT80'
746 wireless.radio1.__toggle='Enable'
747 wireless.radio1.country='00'
748 wireless.radio1.legacy_rates='1'
749 wireless.default_radio1=wifi-iface
750 wireless.default_radio1.device='radio1'
751 wireless.default_radio1.network='lan'
752 wireless.default_radio1.mode='ap'
753 wireless.default_radio1.ssid='asdf'
754 wireless.default_radio1.encryption='psk2'
755 wireless.default_radio1.key='qwerty1234'
756 root@OpenWrt:/etc#
757 {{/code}}
758
759 Firmware:
760
761 ./staging_dir/target-mipsel_24kc_glibc/root-ramips/lib/firmware/mediatek/mt7615_rom_patch.bin