Last modified by Leon Poon on 2021/07/16 18:40
From version 12.1
edited by Leon Poon
on 2019/11/02 14:42
Change comment: There is no comment for this version
To version 21.1
edited by Leon Poon
on 2020/05/31 13:25
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -1,8 +1,38 @@
1 1  switch0: port 0 = wan, port 1,2,3,4 = lan
2 2  
3 +If you brick your router you should be able to recover by soldering the UART pin headers and connecting to the serial. See [[this page for pictures>>doc:Linksys EA8100.WebHome]].
3 3  
4 -[[https:~~/~~/github.com/LeonPoon/openwrt/compare/master...master-linksys_ea8100>>https://github.com/LeonPoon/openwrt/compare/master...master-linksys_ea8100]]
5 5  
6 += 19.07.x =
7 +
8 +(Link deleted - issue discovered - fixing.)
9 +
10 +The EA8100 contains 2 firmware partitions. Using the Linksys UI will flash openwrt into only one of the 2 partitions. The booting process switches partition every few boots, so if you want to always boot into openwrt then you have to flash openwrt into both partitions.
11 +
12 +How to flash:
13 +
14 +If your router currently has stock Linksys firmware:
15 +
16 +1. Flash the "squashfs-factory.img" via Linksys UI, Wait for it to start to reboot.
17 +1. Configure your computer to have ip in 192.168.1.0/24 subnet but NOT 192.168.1.1. (so, use 192.168.1.2.) Start ping to 192.168.1.1.
18 +1. Cross your fingers that the router boots openwrt. Otherwise keep rebooting until it loads the openwrt partition. (Usually 3 times max.) Wait a few minutes from reboot to let it load. If you get response from ping 192.168.1.1 it means openwrt loaded.
19 +1. Access LuCI via LAN. (http:~/~/192.168.1.1). Set root password so that SSH server starts. (Do not configure/restart.) This root password is only temporary.
20 +1. Scp the "squashfs-sysupgrade.bin" into /tmp in the router.
21 +1. Log in as root via SSH and the password you set.
22 +1. Sysupgrade the squashfs-sysupgrade.bin. This should flash the openwrt firmware into both firmware partitions. It auto reboots.
23 +1. Access LuCI via 192.168.1.1 again. You can configure for real now.
24 +
25 +If you are on my 18.x below, sysupgrade will not work. You have to manually mtd write the 19.07 "kernel-initramfs.bin" into the nand and boot/log into it (192.168.1.1), then sysupgrade.
26 +
27 +Sysupgrade will wipe entire firmware partitions! Backup your files/config before sysupgrade.
28 +
29 +Subsequently sysupgrade from 19.07.x should work.
30 +
31 +Wifi seem to work at 30-40MB/s with a MacBook Pro.
32 +
33 +
34 += 18.x =
35 +
6 6  9bebafcb5dfe37f25285fa18fb8bfe7b68011267 (with wifi support) Download:
7 7  
8 8  * [[initramfs-kernel.bin>>attach:openwrt-ramips-mt7621-linksys_ea8100-initramfs-kernel-9bebafcb5dfe37f25285fa18fb8bfe7b68011267.bin]]