switch0: port 0 = wan, port 1,2,3,4 = lan
https://github.com/LeonPoon/openwrt/compare/master...master-linksys_ea8100
9bebafcb5dfe37f25285fa18fb8bfe7b68011267 (with wifi support) Download:
- (accepted as upgrade in factory UI)
Note that sysupgrade to a newer image is not likely to work.
 |
Dmesg:
3: Boot system code via Flash (default).
4: Entr boot command line interface.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP. 4
You choosed 2
0
2: System Load Linux Kernel then write to Flash via TFTP.
Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N)
Please Input new ones /or Ctrl-C to discard
Input device IP () ==:
Input server IP () ==:
Input Linux Kernel filename (openwrt-ramips-mt7621-linksys_ea8100-initramfs-kernel.bin) ==:openwrt-ramips-mt7621-linksys_ea8100-squashfs-sysupgrade.bin
which kernel partition to update (1/2/3=both) (2) ==:3
NetTxPacket = 0x8FFE3200
KSEG1ADDR(NetTxPacket) = 0xAFFE3200
NetLoop,call eth_halt !
NetLoop,call eth_init !
Trying Eth0 (10/100-M)
Waitting for RX_DMA_BUSY status Start... done
ETH_STATE_ACTIVE!!
TFTP from server ; our IP address is
Filename 'openwrt-ramips-mt7621-linksys_ea8100-squashfs-sysupgrade.bin'.
TIMEOUT_COUNT=10,Load address: 0x80100000
Loading: Got ARP REPLY, set server/gtwy eth addr ()
Got it
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
################################################
done
Bytes transferred = 5898496 (5a0100 hex)
LoadAddr=80100000 NetBootFileXferSize= 005a0100
ranand_erase: start:180000, len:20000
..ranand_erase: start:1a0000, len:20000
..ranand_erase: start:1c0000, len:20000
...
.(5192)offs=7471104 piece=0 piece_size=256 rc=0
Done!
ranand_erase: start:2980000, len:20000
..ranand_erase: start:29a0000, len:20000
..ranand_erase: start:29c0000, len:20000
...
.(5192)offs=49676288 piece=0 piece_size=256 rc=0
Done!
## Booting image at bc180000 ...
Image Name: MIPS OpenWrt Linux-4.14.141
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 2010110 Bytes = 1.9 MB
Load Address: 80001000
Entry Point: 80001000
............................... Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80001000) ...
## Giving linux memsize in MB, 256
Starting kernel ...
[ 0.000000] Linux version 4.14.141 () (gcc version 7.4.0 (OpenWrt GCC 7.4.0 r10942-9bebafcb5d)) #0 SMP Sun Sep 1 06:04:50 2019
[ 0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
[ 0.000000] MIPS: machine is Linksys EA8100
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 10000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] VPE topology {2,2} total 4
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] HighMem empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] random: get_random_bytes called from start_kernel+0x9c/0x4d8 with crng_init=0
[ 0.000000] percpu: Embedded 14 pages/cpu s26064 r8192 d23088 u57344
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 64960
[ 0.000000] Kernel command line: console=ttyS0,115200n8 rootfstype=squashfs,jffs2
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Writing ErrCtl register=0002c420
[ 0.000000] Readback ErrCtl register=0002c420
[ 0.000000] Memory: 251700K/262144K available (4796K kernel code, 251K rwdata, 1040K rodata, 1260K init, 254K bss, 10444K reserved, 0K cma-reserved, 0K highmem)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS: 256
[ 0.000000] CPU Clock: 880MHz
[ 0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4343773742 ns
[ 0.000009] sched_clock: 32 bits at 440MHz, resolution 2ns, wraps every 4880645118ns
[ 0.007802] Calibrating delay loop... 586.13 BogoMIPS (lpj=2930688)
[ 0.073969] pid_max: default: 32768 minimum: 301
[ 0.078775] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.085284] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.094340] Hierarchical SRCU implementation.
[ 0.099495] smp: Bringing up secondary CPUs ...
[ 0.114811] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.114820] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.114831] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.114963] CPU1 revision is: 0001992f (MIPS 1004Kc)
[ 0.164211] Synchronize counters for CPU 1: done.
[ 0.208189] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.208197] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.208206] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.208284] CPU2 revision is: 0001992f (MIPS 1004Kc)
[ 0.255179] Synchronize counters for CPU 2: done.
[ 0.295789] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.295797] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.295805] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.295885] CPU3 revision is: 0001992f (MIPS 1004Kc)
[ 0.340367] Synchronize counters for CPU 3: done.
[ 0.370232] smp: Brought up 1 node, 4 CPUs
[ 0.378204] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.388001] futex hash table entries: 1024 (order: 3, 32768 bytes)
[ 0.394408] pinctrl core: initialized pinctrl subsystem
[ 0.401009] NET: Registered protocol family 16
[ 0.415266] pull PCIe RST: RALINK_RSTCTRL = 4000000
[ 0.720548] release PCIe RST: RALINK_RSTCTRL = 7000000
[ 0.725598] ***** Xtal 40MHz *****
[ 0.728952] release PCIe RST: RALINK_RSTCTRL = 7000000
[ 0.734049] Port 0 N_FTS = 1b102800
[ 0.737517] Port 1 N_FTS = 1b102800
[ 0.740963] Port 2 N_FTS = 1b102800
[ 1.896358] PCIE2 no card, disable it(RST&CLK)
[ 1.900719] -> 21007f2
[ 1.903123] PCIE0 enabled
[ 1.905712] PCIE1 enabled
[ 1.908316] PCI host bridge /pcie@1e140000 ranges:
[ 1.913096] MEM 0x0000000060000000..0x000000006fffffff
[ 1.918245] IO 0x000000001e160000..0x000000001e16ffff
[ 1.923451] PCI coherence region base: 0xbfbf8000, mask/settings: 0x60000000
[ 1.939415] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 1.945254] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 1.950961] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 1.958178] PCI host bridge to bus 0000:00
[ 1.962213] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
[ 1.969068] pci_bus 0000:00: root bus resource [io 0xffffffff]
[ 1.974896] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[ 1.981655] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 1.990318] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 1.998262] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 2.007510] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
[ 2.014070] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
[ 2.020937] pci 0000:00:01.0: BAR 0: no space for [mem size 0x80000000]
[ 2.027521] pci 0000:00:01.0: BAR 0: failed to assign [mem size 0x80000000]
[ 2.034415] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
[ 2.041173] pci 0000:00:01.0: BAR 8: assigned [mem 0x60100000-0x601fffff]
[ 2.047897] pci 0000:00:00.0: BAR 1: assigned [mem 0x60200000-0x6020ffff]
[ 2.054657] pci 0000:00:01.0: BAR 1: assigned [mem 0x60210000-0x6021ffff]
[ 2.061377] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit]
[ 2.068661] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 2.073551] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff]
[ 2.080327] pci 0000:02:00.0: BAR 0: assigned [mem 0x60100000-0x601fffff 64bit]
[ 2.087559] pci 0000:00:01.0: PCI bridge to [bus 02]
[ 2.092502] pci 0000:00:01.0: bridge window [mem 0x60100000-0x601fffff]
[ 2.100582] clocksource: Switched to clocksource GIC
[ 2.107275] NET: Registered protocol family 2
[ 2.112196] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[ 2.119081] TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
[ 2.125539] TCP: Hash tables configured (established 2048 bind 2048)
[ 2.131955] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 2.137713] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 2.144212] NET: Registered protocol family 1
[ 2.380532] 4 CPUs re-calibrate udelay(lpj = 2924544)
[ 2.387039] Crashlog allocated RAM at address 0x3f00000
[ 2.392460] workingset: timestamp_bits=14 max_order=16 bucket_order=2
[ 2.408000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 2.413806] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 2.425815] random: fast init done
[ 2.430745] io scheduler noop registered
[ 2.434579] io scheduler deadline registered (default)
[ 2.440747] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled
[ 2.448257] console [ttyS0] disabled
[ 2.451855] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 19, base_baud = 3125000) is a 16550A
[ 2.460836] console [ttyS0] enabled
[ 2.460836] console [ttyS0] enabled
[ 2.467691] bootconsole [early0] disabled
[ 2.467691] bootconsole [early0] disabled
[ 2.477567] MediaTek Nand driver init, version v2.1 Fix AHB virt2phys error
[ 2.484816] Enable NFI Clock
[ 2.487689] # MTK NAND # : Use HW ECC
[ 2.491382] Device not found, ID: c2f1
[ 2.495110] Not Support this Device!
[ 2.498835] chip_mode=00000001
[ 2.501893] Support this Device in MTK table! c2f1
[ 2.506840] [NAND]select ecc bit:4, sparesize :64 spare_per_sector=16
[ 2.513320] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xf1
[ 2.519642] nand: Macronix NAND 128MiB 3,3V 8-bit
[ 2.524347] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 2.531927] Scanning device for bad blocks
[ 2.819771] 7 fixed-partitions partitions found on MTD device MT7621-NAND
[ 2.826546] Creating 7 MTD partitions on "MT7621-NAND":
[ 2.831774] 0x000000000000-0x000000080000 : "uboot"
[ 2.837706] 0x000000080000-0x0000000c0000 : "uboot_env"
[ 2.843891] 0x0000000c0000-0x000000100000 : "factory"
[ 2.849892] 0x000000100000-0x000000140000 : "s_env"
[ 2.855720] 0x000000140000-0x000000180000 : "devinfo"
[ 2.861732] 0x000000180000-0x000002980000 : "firmware1"
[ 2.870032] 0x000002980000-0x000005180000 : "firmware2"
[ 2.877154] 1 uboot-env-boot_part partitions found on MTD device firmware2
[ 2.884061] 0x000002980000-0x000005180000 : "firmware"
[ 3.438509] 2 uimage-fw partitions found on MTD device firmware
[ 3.444473] 0x000002980000-0x000002b80000 : "kernel"
[ 3.450603] 0x000002b80000-0x000005180000 : "ubi"
[ 3.456742] [mtk_nand] probe successfully!
[ 3.461570] Signature matched and data read!
[ 3.465818] load_fact_bbt success 1023
[ 3.470276] libphy: Fixed MDIO Bus: probed
[ 3.542951] mtd_read_prop_mac: find prop "hw_mac_addr" in devinfo(max 0x40000) from 0x0
[ 3.550970] mtd_read_prop_mac: hw_mac_addr=
[ 3.556774] libphy: mdio: probed
[ 4.961009] mtk_soc_eth 1e100000.ethernet: loaded mt7530 driver
[ 4.967662] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 21
[ 4.978262] NET: Registered protocol family 10
[ 4.984286] Segment Routing with IPv6
[ 4.988020] NET: Registered protocol family 17
[ 4.992556] 8021q: 802.1Q VLAN Support v1.8
[ 4.999621] UBI: auto-attach mtd9
[ 5.003015] ubi0: attaching mtd9
[ 5.033798] UBI: EOF marker found, PEBs from 25 will be erased
[ 5.039967] ubi0: scanning is finished
[ 5.081872] ubi0: volume 1 ("rootfs_data") re-sized from 9 to 258 LEBs
[ 5.089203] ubi0: attached mtd9 (name "ubi", size 38 MiB)
[ 5.094644] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 5.101543] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 5.108298] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 5.115245] ubi0: good PEBs: 297, bad PEBs: 7, corrupted PEBs: 0
[ 5.121247] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
[ 5.128436] ubi0: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number:
[ 5.137541] ubi0: available PEBs: 0, total reserved PEBs: 297, PEBs reserved for bad PEB handling: 13
[ 5.146764] ubi0: background thread "ubi_bgt0d" started, PID 378
[ 5.148847] block ubiblock0_0: created from ubi0:0(rootfs)
[ 5.158262] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem
[ 5.165234] hctosys: unable to open rtc device (rtc0)
[ 5.183831] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[ 5.195491] Freeing unused kernel memory: 1260K
[ 5.200022] This architecture does not have kernel memory protection.
[ 5.783744] init: Console is alive
[ 5.787378] init: - watchdog -
[ 6.295000] mtk_soc_eth 1e100000.ethernet eth0: port 1 link up
[ 6.502425] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 6.591413] usbcore: registered new interface driver usbfs
[ 6.596966] usbcore: registered new interface driver hub
[ 6.602453] usbcore: registered new device driver usb
[ 6.615285] SCSI subsystem initialized
[ 6.626976] xhci-mtk 1e1c0000.xhci: 1e1c0000.xhci supply vbus not found, using dummy regulator
[ 6.635689] xhci-mtk 1e1c0000.xhci: 1e1c0000.xhci supply vusb33 not found, using dummy regulator
[ 6.644627] xhci-mtk 1e1c0000.xhci: xHCI Host Controller
[ 6.649947] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 1
[ 6.660739] xhci-mtk 1e1c0000.xhci: hcc params 0x01401198 hci version 0x96 quirks 0x0000000000210010
[ 6.669906] xhci-mtk 1e1c0000.xhci: irq 20, io mem 0x1e1c0000
[ 6.676639] hub 1-0:1.0: USB hub found
[ 6.680467] hub 1-0:1.0: 2 ports detected
[ 6.685052] xhci-mtk 1e1c0000.xhci: xHCI Host Controller
[ 6.690366] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 2
[ 6.697886] xhci-mtk 1e1c0000.xhci: Host supports USB 3.0 SuperSpeed
[ 6.704507] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 6.713446] hub 2-0:1.0: USB hub found
[ 6.717275] hub 2-0:1.0: 1 port detected
[ 6.727313] usbcore: registered new interface driver usb-storage
[ 6.733578] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 6.750877] init: - preinit -
[ 7.180814] usb 2-1: new SuperSpeed USB device number 2 using xhci-mtk
[ 7.212805] random: procd: uninitialized urandom read (4 bytes read)
[ 7.212971] usb-storage 2-1:1.0: USB Mass Storage device detected
[ 7.225920] scsi host0: usb-storage 2-1:1.0
[ 7.366240] mtk_soc_eth 1e100000.ethernet: PPE started
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 10.582466] UBIFS (ubi0:1): default file-system created
[ 10.589130] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 496
[ 10.700430] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[ 10.708276] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 10.718161] UBIFS (ubi0:1): FS size: 31490048 bytes (30 MiB, 248 LEBs), journal size 1523712 bytes (1 MiB, 12 LEBs)
[ 10.728565] UBIFS (ubi0:1): reserved for root: 1487352 bytes (1452 KiB)
[ 10.735166] UBIFS (ubi0:1): media format: w4/r0 (latest is w5/r0), UUID , small LPT model
[ 10.749347] mount_root: overlay filesystem has not been fully initialized yet
[ 10.756981] mount_root: switching to ubifs overlay
[ 10.781065] urandom-seed: Seed file not found (/etc/urandom.seed)
[ 10.861172] mtk_soc_eth 1e100000.ethernet: 0x100 = 0x6060000c, 0x10c = 0x80818
[ 10.876085] procd: - early -
[ 10.879061] procd: - watchdog -
[ 11.550737] procd: - watchdog -
[ 11.554202] procd: - ubus -
[ 11.583502] random: ubusd: uninitialized urandom read (4 bytes read)
[ 11.611421] random: ubusd: uninitialized urandom read (4 bytes read)
[ 11.618117] random: ubusd: uninitialized urandom read (4 bytes read)
[ 11.625387] procd: - init -
Please press Enter to activate this console.
[ 12.046531] kmodloader: loading kernel modules from /etc/modules.d/*
[ 12.057746] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 12.069204] Loading modules backported from Linux version v5.3-rc4-0-gd45331b00ddb
[ 12.076775] Backport generated by backports.git v5.3-rc4-1-0-g4ec72687
[ 12.085114] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 12.096731] nf_conntrack version 0.5.0 (4096 buckets, 16384 max)
[ 12.127574] urngd: v1.0.0 started.
[ 12.145053] xt_time: kernel timezone is -0000
[ 12.214244] bus=0x1, slot = 0x0, irq=0x0
[ 12.218201] PCI: Enabling device 0000:00:00.0 (0004 -> 0006)
[ 12.241178] mt7615e 0000:01:00.0: HW/SW Version: 0x8a108a10, Build Time: 20180518100604a
[ 12.241178]
[ 12.266469] random: crng init done
[ 12.269877] random: 6 urandom warning(s) missed due to ratelimiting
[ 12.456236] mt7615e 0000:01:00.0: N9 Firmware Version: _reserved_, Build Time: 20190103180756
[ 12.471995] mt7615e 0000:01:00.0: CR4 Firmware Version: _reserved_, Build Time: 20181207140436
+ýýrýýýýýýýbus=0x2, slot = 0x1, irq=0x0
[ 20.131310] PCI: Enabling device 0000:00:01.0 (0004 -> 0006)
[ 20.161193] mt7615e 0000:02:00.0: HW/SW Version: 0x8a108a10, Build Time: 20180518100604a
[ 20.161193]
[ 20.185604] mt7615e 0000:02:00.0: N9 Firmware Version: _reserved_, Build Time: 20190103180756
[ 20.200746] mt7615e 0000:02:00.0: CR4 Firmware Version: _reserved_, Build Time: 20181207140436
[ 27.852570] PPP generic driver version 2.4.2
[ 27.858358] NET: Registered protocol family 24
[ 27.866716] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 41.276638] mtk_soc_eth 1e100000.ethernet: PPE started
[ 41.287935] br-lan: port 1(eth0.2) entered blocking state
[ 41.293420] br-lan: port 1(eth0.2) entered disabled state
[ 41.299522] device eth0.2 entered promiscuous mode
[ 41.304484] device eth0 entered promiscuous mode
[ 41.311947] br-lan: port 1(eth0.2) entered blocking state
[ 41.317384] br-lan: port 1(eth0.2) entered forwarding state
[ 41.323511] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 42.321086] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
BusyBox v1.31.0 () built-in shell (ash)
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
OpenWrt SNAPSHOT, r10942-9bebafcb5d
-----------------------------------------------------
=== WARNING! =====================================
There is no root password defined on this device!
Use the "passwd" command to set up a new password
in order to prevent unauthorized SSH logins.
--------------------------------------------------
root@OpenWrt:/# ifconfig -a
br-lan Link encap:Ethernet HWaddr
inet addr:192.168.1.1 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fde0:62db:5134::1/60 Scope:Global
inet6 addr: fe80::/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:41 errors:0 dropped:0 overruns:0 frame:0
TX packets:13 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:8012 (7.8 KiB) TX bytes:2126 (2.0 KiB)
eth0 Link encap:Ethernet HWaddr
inet6 addr: fe80::/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:102 errors:0 dropped:0 overruns:0 frame:0
TX packets:47 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:19418 (18.9 KiB) TX bytes:8199 (8.0 KiB)
Interrupt:21
eth0.1 Link encap:Ethernet HWaddr
inet6 addr: fe80::/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:20 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:3368 (3.2 KiB)
eth0.2 Link encap:Ethernet HWaddr
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:41 errors:0 dropped:0 overruns:0 frame:0
TX packets:13 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:8012 (7.8 KiB) TX bytes:2126 (2.0 KiB)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:28 errors:0 dropped:0 overruns:0 frame:0
TX packets:28 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:1904 (1.8 KiB) TX bytes:1904 (1.8 KiB)
wlan0 Link encap:Ethernet HWaddr
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
wlan1 Link encap:Ethernet HWaddr
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
root@OpenWrt:/# ls -l
drwxr-xr-x 2 root root 778 Sep 1 06:04 bin
drwxr-xr-x 4 root root 1300 Sep 1 06:05 dev
drwxr-xr-x 1 root root 512 Sep 1 06:05 etc
-rwxr-xr-x 1 root root 78 Dec 30 2018 init
drwxr-xr-x 11 root root 426 Sep 1 06:04 lib
drwxr-xr-x 2 root root 3 Sep 1 06:04 mnt
drwxr-xr-x 4 root root 360 Sep 1 06:05 overlay
dr-xr-xr-x 73 root root 0 Jan 1 1970 proc
drwxr-xr-x 16 root root 223 Sep 1 06:04 rom
drwxr-xr-x 2 root root 3 Sep 1 06:04 root
drwxr-xr-x 2 root root 822 Sep 1 06:04 sbin
dr-xr-xr-x 11 root root 0 Jan 1 1970 sys
drwxrwxrwt 15 root root 380 Sep 1 06:05 tmp
drwxr-xr-x 7 root root 89 Sep 1 06:04 usr
lrwxrwxrwx 1 root root 3 Sep 1 06:04 var -> tmp
drwxr-xr-x 2 root root 3 Sep 1 06:04 www
root@OpenWrt:/# ps
PID USER VSZ STAT COMMAND
1 root 1576 S /sbin/procd
2 root 0 SW [kthreadd]
3 root 0 IW [kworker/0:0]
4 root 0 IW< [kworker/0:0H]
5 root 0 IW [kworker/u8:0]
6 root 0 IW< [mm_percpu_wq]
7 root 0 SW [ksoftirqd/0]
8 root 0 IW [rcu_sched]
9 root 0 IW [rcu_bh]
10 root 0 SW [migration/0]
11 root 0 SW [cpuhp/0]
12 root 0 SW [cpuhp/1]
13 root 0 SW [migration/1]
14 root 0 SW [ksoftirqd/1]
16 root 0 IW< [kworker/1:0H]
17 root 0 SW [cpuhp/2]
18 root 0 SW [migration/2]
19 root 0 SW [ksoftirqd/2]
21 root 0 IW< [kworker/2:0H]
22 root 0 SW [cpuhp/3]
23 root 0 SW [migration/3]
24 root 0 SW [ksoftirqd/3]
25 root 0 IW [kworker/3:0]
26 root 0 IW< [kworker/3:0H]
27 root 0 IW< [netns]
41 root 0 IW [kworker/u8:3]
68 root 0 IW [kworker/3:1]
69 root 0 IW [kworker/2:1]
138 root 0 IW [kworker/1:1]
139 root 0 SW [oom_reaper]
140 root 0 IW< [writeback]
142 root 0 SW [kcompactd0]
143 root 0 IW< [crypto]
145 root 0 IW< [kblockd]
175 root 0 IW< [watchdogd]
199 root 0 SW [kswapd0]
268 root 0 IW< [pencrypt]
270 root 0 IW< [pdecrypt]
366 root 0 IW< [ipv6_addrconf]
378 root 0 SW [ubi_bgt0d]
383 root 0 IW< [kworker/0:1H]
384 root 0 IW< [kworker/2:1H]
385 root 0 IW [kworker/2:2]
386 root 0 IW< [kworker/3:1H]
389 root 0 IW< [kworker/1:1H]
429 root 0 IW [kworker/0:2]
437 root 0 IW [kworker/1:2]
453 root 0 SW [scsi_eh_0]
454 root 0 IW< [scsi_tmf_0]
455 root 0 SW [usb-storage]
496 root 0 SW [ubifs_bgt0_1]
573 root 1220 S /sbin/ubusd
574 root 1220 S /bin/ash --login
591 root 1028 S /sbin/urngd
660 root 0 IW< [cfg80211]
1012 root 1248 S /sbin/logd -S 64
1074 dnsmasq 1344 S /usr/sbin/dnsmasq -C /var/etc/dnsmasq.conf.cfg01411c
1111 root 1080 S /usr/sbin/dropbear -F -P /var/run/dropbear.1.pid -p
1168 root 1700 S /sbin/netifd
1204 root 1448 S /usr/sbin/odhcpd
1360 root 1212 S udhcpc -p /var/run/udhcpc-eth0.1.pid -s /lib/netifd/
1361 root 1052 S odhcp6c -s /lib/netifd/dhcpv6.script -P0 -t120 eth0.
1391 root 1212 S< /usr/sbin/ntpd -n -N -S /usr/sbin/ntpd-hotplug -p 0.
1720 root 1212 R ps
root@OpenWrt:/etc# ping www.google.co
PING www.google.co (): 56 data bytes
64 bytes from : seq=0 ttl=52 time=4.718 ms
^C
--- www.google.co ping statistics ---
1 packets transmitted, 1 packets received, 0% packet loss
round-trip min/avg/max = 4.718/4.718/4.718 ms
root@OpenWrt:/etc# ping www.google.com
PING www.google.com (): 56 data bytes
64 bytes from : seq=0 ttl=47 time=4.927 ms
64 bytes from : seq=1 ttl=47 time=4.687 ms
^C
--- www.google.com ping statistics ---
2 packets transmitted, 2 packets received, 0% packet loss
round-trip min/avg/max = 4.687/4.807/4.927 ms
root@OpenWrt:/etc# opkg update
Downloading http://downloads.openwrt.org/snapshots/targets/ramips/mt7621/packages/Packages.gz
Updated list of available packages in /var/opkg-lists/openwrt_core
Downloading http://downloads.openwrt.org/snapshots/targets/ramips/mt7621/packages/Packages.sig
Signature check passed.
Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/base/Packages.gz
Updated list of available packages in /var/opkg-lists/openwrt_base
Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/base/Packages.sig
Signature check passed.
Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/Packages.gz
Updated list of available packages in /var/opkg-lists/openwrt_luci
Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/Packages.sig
Signature check passed.
Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/packages/Packages.gz
Updated list of available packages in /var/opkg-lists/openwrt_packages
Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/packages/Packages.sig
Signature check passed.
Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/routing/Packages.gz
Updated list of available packages in /var/opkg-lists/openwrt_routing
Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/routing/Packages.sig
Signature check passed.
Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/telephony/Packages.gz
Updated list of available packages in /var/opkg-lists/openwrt_telephony
Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/telephony/Packages.sig
Signature check passed.
root@OpenWrt:/etc# opkg install luci
Installing luci (git-19.241.65047-dffe9ca-1) to root...
Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/luci_git-19.241.65047-dffe9ca-1_all.ipk
Installing uhttpd (2019-08-17-6b03f960-3) to root...
Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/base/uhttpd_2019-08-17-6b03f960-3_mipsel_24kc.ipk
Installing liblua5.1.5 (5.1.5-5) to root...
Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/base/liblua5.1.5_5.1.5-5_mipsel_24kc.ipk
Installing lua (5.1.5-5) to root...
Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/base/lua_5.1.5-5_mipsel_24kc.ipk
Installing luci-lib-nixio (git-19.241.65047-dffe9ca-1) to root...
Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/luci-lib-nixio_git-19.241.65047-dffe9ca-1_mipsel_24kc.ipk
Installing luci-lib-ip (git-19.241.65047-dffe9ca-1) to root...
Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/luci-lib-ip_git-19.241.65047-dffe9ca-1_mipsel_24kc.ipk
Installing rpcd (2019-06-05-89bfaa42-3) to root...
Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/base/rpcd_2019-06-05-89bfaa42-3_mipsel_24kc.ipk
Installing libubus-lua (2018-10-06-221ce7e7-1) to root...
Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/base/libubus-lua_2018-10-06-221ce7e7-1_mipsel_24kc.ipk
Installing luci-lib-jsonc (git-19.241.65047-dffe9ca-1) to root...
Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/luci-lib-jsonc_git-19.241.65047-dffe9ca-1_mipsel_24kc.ipk
Installing liblucihttp0 (2019-07-05-a34a17d5-1) to root...
Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/liblucihttp0_2019-07-05-a34a17d5-1_mipsel_24kc.ipk
Installing liblucihttp-lua (2019-07-05-a34a17d5-1) to root...
Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/liblucihttp-lua_2019-07-05-a34a17d5-1_mipsel_24kc.ipk
Installing luci-base (git-19.241.65047-dffe9ca-1) to root...
Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/luci-base_git-19.241.65047-dffe9ca-1_mipsel_24kc.ipk
Installing libiwinfo-lua (2019-08-28-a9f95570-1) to root...
Downloading http://downloads.openwrt.org/snapshots/targets/ramips/mt7621/packages/libiwinfo-lua_2019-08-28-a9f95570-1_mipsel_24kc.ipk
Installing luci-mod-status (git-19.241.65047-dffe9ca-1) to root...
Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/luci-mod-status_git-19.241.65047-dffe9ca-1_mipsel_24kc.ipk
Installing luci-mod-system (git-19.241.65047-dffe9ca-1) to root...
Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/luci-mod-system_git-19.241.65047-dffe9ca-1_all.ipk
Installing luci-mod-network (git-19.241.65047-dffe9ca-1) to root...
Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/luci-mod-network_git-19.241.65047-dffe9ca-1_all.ipk
Installing luci-mod-admin-full (git-19.241.65047-dffe9ca-1) to root...
Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/luci-mod-admin-full_git-19.241.65047-dffe9ca-1_all.ipk
Installing luci-theme-bootstrap (git-19.241.65047-dffe9ca-1) to root...
Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/luci-theme-bootstrap_git-19.241.65047-dffe9ca-1_all.ipk
Installing luci-app-firewall (git-19.241.65047-dffe9ca-1) to root...
Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/luci-app-firewall_git-19.241.65047-dffe9ca-1_all.ipk
Installing luci-app-opkg (git-19.241.65047-dffe9ca-1) to root...
Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/luci-app-opkg_git-19.241.65047-dffe9ca-1_all.ipk
Installing luci-proto-ppp (git-19.241.65047-dffe9ca-1) to root...
Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/luci-proto-ppp_git-19.241.65047-dffe9ca-1_all.ipk
Installing luci-proto-ipv6 (git-19.241.65047-dffe9ca-1) to root...
Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/luci-proto-ipv6_git-19.241.65047-dffe9ca-1_all.ipk
Installing rpcd-mod-rrdns (20170710) to root...
Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/rpcd-mod-rrdns_20170710_mipsel_24kc.ipk
Configuring liblucihttp0.
Configuring luci-app-opkg.
Configuring rpcd.
Configuring liblua5.1.5.
Configuring luci-lib-ip.
Configuring libubus-lua.
Configuring libiwinfo-lua.
Configuring lua.
Configuring luci-lib-nixio.
Configuring luci-lib-jsonc.
Configuring liblucihttp-lua.
Configuring luci-base.
Configuring luci-mod-system.
Configuring luci-theme-bootstrap.
Configuring luci-mod-status.
Configuring luci-app-firewall.
Configuring luci-proto-ppp.
Configuring luci-mod-network.
Configuring luci-mod-admin-full.
Configuring luci-proto-ipv6.
Configuring uhttpd.
Configuring rpcd-mod-rrdns.
Configuring luci.
root@OpenWrt:/etc# df -h
Filesystem Size Used Available Use% Mounted on
/dev/root 2.8M 2.8M 0 100% /rom
tmpfs 123.5M 764.0K 122.8M 1% /tmp
/dev/ubi0_1 27.1M 1.4M 24.3M 5% /overlay
overlayfs:/overlay 27.1M 1.4M 24.3M 5% /
tmpfs 512.0K 0 512.0K 0% /dev
root@OpenWrt:/etc# [ 2075.963720] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 2075.973245] br-lan: port 2(wlan0) entered blocking state
[ 2075.978551] br-lan: port 2(wlan0) entered disabled state
[ 2075.984368] device wlan0 entered promiscuous mode
[ 2087.165173] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 2087.171890] br-lan: port 2(wlan0) entered blocking state
[ 2087.177194] br-lan: port 2(wlan0) entered forwarding state
[ 2096.494533] device wlan0 left promiscuous mode
[ 2096.499322] br-lan: port 2(wlan0) entered disabled state
[ 2097.382887] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 2097.393568] br-lan: port 2(wlan0) entered blocking state
[ 2097.398924] br-lan: port 2(wlan0) entered disabled state
[ 2097.404922] device wlan0 entered promiscuous mode
[ 2097.409972] br-lan: port 2(wlan0) entered blocking state
[ 2097.415296] br-lan: port 2(wlan0) entered forwarding state
[ 2097.749351] br-lan: port 2(wlan0) entered disabled state
[ 2107.953875] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 2107.960561] br-lan: port 2(wlan0) entered blocking state
[ 2107.965861] br-lan: port 2(wlan0) entered forwarding state
[ 2117.964353] device wlan0 left promiscuous mode
[ 2117.969130] br-lan: port 2(wlan0) entered disabled state
[ 2118.782586] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 2118.792816] br-lan: port 2(wlan0) entered blocking state
[ 2118.798173] br-lan: port 2(wlan0) entered disabled state
[ 2118.804171] device wlan0 entered promiscuous mode
[ 2118.809362] br-lan: port 2(wlan0) entered blocking state
[ 2118.814692] br-lan: port 2(wlan0) entered forwarding state
[ 2119.189273] br-lan: port 2(wlan0) entered disabled state
[ 2130.258107] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 2130.264811] br-lan: port 2(wlan0) entered blocking state
[ 2130.270163] br-lan: port 2(wlan0) entered forwarding state
[ 2245.748473] device wlan0 left promiscuous mode
[ 2245.753145] br-lan: port 2(wlan0) entered disabled state
[ 2246.536062] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 2246.546273] br-lan: port 2(wlan0) entered blocking state
[ 2246.551680] br-lan: port 2(wlan0) entered disabled state
[ 2246.557667] device wlan0 entered promiscuous mode
[ 2246.562855] br-lan: port 2(wlan0) entered blocking state
[ 2246.568267] br-lan: port 2(wlan0) entered forwarding state
[ 2246.838430] br-lan: port 2(wlan0) entered disabled state
[ 2246.948147] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[ 2246.954850] br-lan: port 2(wlan1) entered blocking state
[ 2246.960197] br-lan: port 2(wlan1) entered forwarding state
root@OpenWrt:/etc#
root@OpenWrt:/etc# uci show wireless
wireless.radio0=wifi-device
wireless.radio0.type='mac80211'
wireless.radio0.channel='11'
wireless.radio0.hwmode='11g'
wireless.radio0.path='pci0000:00/0000:00:00.0/0000:01:00.0'
wireless.radio0.country='00'
wireless.radio0.legacy_rates='1'
wireless.radio0.htmode='HT20'
wireless.default_radio0=wifi-iface
wireless.default_radio0.device='radio0'
wireless.default_radio0.network='lan'
wireless.default_radio0.mode='ap'
wireless.default_radio0.encryption='psk2'
wireless.default_radio0.key='qwerty1234'
wireless.default_radio0.ssid='asdf'
wireless.radio1=wifi-device
wireless.radio1.type='mac80211'
wireless.radio1.channel='36'
wireless.radio1.hwmode='11a'
wireless.radio1.path='pci0000:00/0000:00:01.0/0000:02:00.0'
wireless.radio1.htmode='VHT80'
wireless.radio1.__toggle='Enable'
wireless.radio1.country='00'
wireless.radio1.legacy_rates='1'
wireless.default_radio1=wifi-iface
wireless.default_radio1.device='radio1'
wireless.default_radio1.network='lan'
wireless.default_radio1.mode='ap'
wireless.default_radio1.ssid='asdf'
wireless.default_radio1.encryption='psk2'
wireless.default_radio1.key='qwerty1234'
root@OpenWrt:/etc#
4: Entr boot command line interface.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP. 4
You choosed 2
0
2: System Load Linux Kernel then write to Flash via TFTP.
Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N)
Please Input new ones /or Ctrl-C to discard
Input device IP () ==:
Input server IP () ==:
Input Linux Kernel filename (openwrt-ramips-mt7621-linksys_ea8100-initramfs-kernel.bin) ==:openwrt-ramips-mt7621-linksys_ea8100-squashfs-sysupgrade.bin
which kernel partition to update (1/2/3=both) (2) ==:3
NetTxPacket = 0x8FFE3200
KSEG1ADDR(NetTxPacket) = 0xAFFE3200
NetLoop,call eth_halt !
NetLoop,call eth_init !
Trying Eth0 (10/100-M)
Waitting for RX_DMA_BUSY status Start... done
ETH_STATE_ACTIVE!!
TFTP from server ; our IP address is
Filename 'openwrt-ramips-mt7621-linksys_ea8100-squashfs-sysupgrade.bin'.
TIMEOUT_COUNT=10,Load address: 0x80100000
Loading: Got ARP REPLY, set server/gtwy eth addr ()
Got it
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
################################################
done
Bytes transferred = 5898496 (5a0100 hex)
LoadAddr=80100000 NetBootFileXferSize= 005a0100
ranand_erase: start:180000, len:20000
..ranand_erase: start:1a0000, len:20000
..ranand_erase: start:1c0000, len:20000
...
.(5192)offs=7471104 piece=0 piece_size=256 rc=0
Done!
ranand_erase: start:2980000, len:20000
..ranand_erase: start:29a0000, len:20000
..ranand_erase: start:29c0000, len:20000
...
.(5192)offs=49676288 piece=0 piece_size=256 rc=0
Done!
## Booting image at bc180000 ...
Image Name: MIPS OpenWrt Linux-4.14.141
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 2010110 Bytes = 1.9 MB
Load Address: 80001000
Entry Point: 80001000
............................... Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80001000) ...
## Giving linux memsize in MB, 256
Starting kernel ...
[ 0.000000] Linux version 4.14.141 () (gcc version 7.4.0 (OpenWrt GCC 7.4.0 r10942-9bebafcb5d)) #0 SMP Sun Sep 1 06:04:50 2019
[ 0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
[ 0.000000] MIPS: machine is Linksys EA8100
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 10000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] VPE topology {2,2} total 4
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] HighMem empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] random: get_random_bytes called from start_kernel+0x9c/0x4d8 with crng_init=0
[ 0.000000] percpu: Embedded 14 pages/cpu s26064 r8192 d23088 u57344
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 64960
[ 0.000000] Kernel command line: console=ttyS0,115200n8 rootfstype=squashfs,jffs2
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Writing ErrCtl register=0002c420
[ 0.000000] Readback ErrCtl register=0002c420
[ 0.000000] Memory: 251700K/262144K available (4796K kernel code, 251K rwdata, 1040K rodata, 1260K init, 254K bss, 10444K reserved, 0K cma-reserved, 0K highmem)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS: 256
[ 0.000000] CPU Clock: 880MHz
[ 0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4343773742 ns
[ 0.000009] sched_clock: 32 bits at 440MHz, resolution 2ns, wraps every 4880645118ns
[ 0.007802] Calibrating delay loop... 586.13 BogoMIPS (lpj=2930688)
[ 0.073969] pid_max: default: 32768 minimum: 301
[ 0.078775] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.085284] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.094340] Hierarchical SRCU implementation.
[ 0.099495] smp: Bringing up secondary CPUs ...
[ 0.114811] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.114820] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.114831] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.114963] CPU1 revision is: 0001992f (MIPS 1004Kc)
[ 0.164211] Synchronize counters for CPU 1: done.
[ 0.208189] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.208197] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.208206] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.208284] CPU2 revision is: 0001992f (MIPS 1004Kc)
[ 0.255179] Synchronize counters for CPU 2: done.
[ 0.295789] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.295797] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.295805] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.295885] CPU3 revision is: 0001992f (MIPS 1004Kc)
[ 0.340367] Synchronize counters for CPU 3: done.
[ 0.370232] smp: Brought up 1 node, 4 CPUs
[ 0.378204] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.388001] futex hash table entries: 1024 (order: 3, 32768 bytes)
[ 0.394408] pinctrl core: initialized pinctrl subsystem
[ 0.401009] NET: Registered protocol family 16
[ 0.415266] pull PCIe RST: RALINK_RSTCTRL = 4000000
[ 0.720548] release PCIe RST: RALINK_RSTCTRL = 7000000
[ 0.725598] ***** Xtal 40MHz *****
[ 0.728952] release PCIe RST: RALINK_RSTCTRL = 7000000
[ 0.734049] Port 0 N_FTS = 1b102800
[ 0.737517] Port 1 N_FTS = 1b102800
[ 0.740963] Port 2 N_FTS = 1b102800
[ 1.896358] PCIE2 no card, disable it(RST&CLK)
[ 1.900719] -> 21007f2
[ 1.903123] PCIE0 enabled
[ 1.905712] PCIE1 enabled
[ 1.908316] PCI host bridge /pcie@1e140000 ranges:
[ 1.913096] MEM 0x0000000060000000..0x000000006fffffff
[ 1.918245] IO 0x000000001e160000..0x000000001e16ffff
[ 1.923451] PCI coherence region base: 0xbfbf8000, mask/settings: 0x60000000
[ 1.939415] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 1.945254] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 1.950961] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 1.958178] PCI host bridge to bus 0000:00
[ 1.962213] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
[ 1.969068] pci_bus 0000:00: root bus resource [io 0xffffffff]
[ 1.974896] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[ 1.981655] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 1.990318] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 1.998262] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 2.007510] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
[ 2.014070] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
[ 2.020937] pci 0000:00:01.0: BAR 0: no space for [mem size 0x80000000]
[ 2.027521] pci 0000:00:01.0: BAR 0: failed to assign [mem size 0x80000000]
[ 2.034415] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
[ 2.041173] pci 0000:00:01.0: BAR 8: assigned [mem 0x60100000-0x601fffff]
[ 2.047897] pci 0000:00:00.0: BAR 1: assigned [mem 0x60200000-0x6020ffff]
[ 2.054657] pci 0000:00:01.0: BAR 1: assigned [mem 0x60210000-0x6021ffff]
[ 2.061377] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit]
[ 2.068661] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 2.073551] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff]
[ 2.080327] pci 0000:02:00.0: BAR 0: assigned [mem 0x60100000-0x601fffff 64bit]
[ 2.087559] pci 0000:00:01.0: PCI bridge to [bus 02]
[ 2.092502] pci 0000:00:01.0: bridge window [mem 0x60100000-0x601fffff]
[ 2.100582] clocksource: Switched to clocksource GIC
[ 2.107275] NET: Registered protocol family 2
[ 2.112196] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[ 2.119081] TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
[ 2.125539] TCP: Hash tables configured (established 2048 bind 2048)
[ 2.131955] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 2.137713] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 2.144212] NET: Registered protocol family 1
[ 2.380532] 4 CPUs re-calibrate udelay(lpj = 2924544)
[ 2.387039] Crashlog allocated RAM at address 0x3f00000
[ 2.392460] workingset: timestamp_bits=14 max_order=16 bucket_order=2
[ 2.408000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 2.413806] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 2.425815] random: fast init done
[ 2.430745] io scheduler noop registered
[ 2.434579] io scheduler deadline registered (default)
[ 2.440747] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled
[ 2.448257] console [ttyS0] disabled
[ 2.451855] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 19, base_baud = 3125000) is a 16550A
[ 2.460836] console [ttyS0] enabled
[ 2.460836] console [ttyS0] enabled
[ 2.467691] bootconsole [early0] disabled
[ 2.467691] bootconsole [early0] disabled
[ 2.477567] MediaTek Nand driver init, version v2.1 Fix AHB virt2phys error
[ 2.484816] Enable NFI Clock
[ 2.487689] # MTK NAND # : Use HW ECC
[ 2.491382] Device not found, ID: c2f1
[ 2.495110] Not Support this Device!
[ 2.498835] chip_mode=00000001
[ 2.501893] Support this Device in MTK table! c2f1
[ 2.506840] [NAND]select ecc bit:4, sparesize :64 spare_per_sector=16
[ 2.513320] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xf1
[ 2.519642] nand: Macronix NAND 128MiB 3,3V 8-bit
[ 2.524347] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 2.531927] Scanning device for bad blocks
[ 2.819771] 7 fixed-partitions partitions found on MTD device MT7621-NAND
[ 2.826546] Creating 7 MTD partitions on "MT7621-NAND":
[ 2.831774] 0x000000000000-0x000000080000 : "uboot"
[ 2.837706] 0x000000080000-0x0000000c0000 : "uboot_env"
[ 2.843891] 0x0000000c0000-0x000000100000 : "factory"
[ 2.849892] 0x000000100000-0x000000140000 : "s_env"
[ 2.855720] 0x000000140000-0x000000180000 : "devinfo"
[ 2.861732] 0x000000180000-0x000002980000 : "firmware1"
[ 2.870032] 0x000002980000-0x000005180000 : "firmware2"
[ 2.877154] 1 uboot-env-boot_part partitions found on MTD device firmware2
[ 2.884061] 0x000002980000-0x000005180000 : "firmware"
[ 3.438509] 2 uimage-fw partitions found on MTD device firmware
[ 3.444473] 0x000002980000-0x000002b80000 : "kernel"
[ 3.450603] 0x000002b80000-0x000005180000 : "ubi"
[ 3.456742] [mtk_nand] probe successfully!
[ 3.461570] Signature matched and data read!
[ 3.465818] load_fact_bbt success 1023
[ 3.470276] libphy: Fixed MDIO Bus: probed
[ 3.542951] mtd_read_prop_mac: find prop "hw_mac_addr" in devinfo(max 0x40000) from 0x0
[ 3.550970] mtd_read_prop_mac: hw_mac_addr=
[ 3.556774] libphy: mdio: probed
[ 4.961009] mtk_soc_eth 1e100000.ethernet: loaded mt7530 driver
[ 4.967662] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 21
[ 4.978262] NET: Registered protocol family 10
[ 4.984286] Segment Routing with IPv6
[ 4.988020] NET: Registered protocol family 17
[ 4.992556] 8021q: 802.1Q VLAN Support v1.8
[ 4.999621] UBI: auto-attach mtd9
[ 5.003015] ubi0: attaching mtd9
[ 5.033798] UBI: EOF marker found, PEBs from 25 will be erased
[ 5.039967] ubi0: scanning is finished
[ 5.081872] ubi0: volume 1 ("rootfs_data") re-sized from 9 to 258 LEBs
[ 5.089203] ubi0: attached mtd9 (name "ubi", size 38 MiB)
[ 5.094644] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 5.101543] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 5.108298] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 5.115245] ubi0: good PEBs: 297, bad PEBs: 7, corrupted PEBs: 0
[ 5.121247] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
[ 5.128436] ubi0: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number:
[ 5.137541] ubi0: available PEBs: 0, total reserved PEBs: 297, PEBs reserved for bad PEB handling: 13
[ 5.146764] ubi0: background thread "ubi_bgt0d" started, PID 378
[ 5.148847] block ubiblock0_0: created from ubi0:0(rootfs)
[ 5.158262] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem
[ 5.165234] hctosys: unable to open rtc device (rtc0)
[ 5.183831] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[ 5.195491] Freeing unused kernel memory: 1260K
[ 5.200022] This architecture does not have kernel memory protection.
[ 5.783744] init: Console is alive
[ 5.787378] init: - watchdog -
[ 6.295000] mtk_soc_eth 1e100000.ethernet eth0: port 1 link up
[ 6.502425] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 6.591413] usbcore: registered new interface driver usbfs
[ 6.596966] usbcore: registered new interface driver hub
[ 6.602453] usbcore: registered new device driver usb
[ 6.615285] SCSI subsystem initialized
[ 6.626976] xhci-mtk 1e1c0000.xhci: 1e1c0000.xhci supply vbus not found, using dummy regulator
[ 6.635689] xhci-mtk 1e1c0000.xhci: 1e1c0000.xhci supply vusb33 not found, using dummy regulator
[ 6.644627] xhci-mtk 1e1c0000.xhci: xHCI Host Controller
[ 6.649947] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 1
[ 6.660739] xhci-mtk 1e1c0000.xhci: hcc params 0x01401198 hci version 0x96 quirks 0x0000000000210010
[ 6.669906] xhci-mtk 1e1c0000.xhci: irq 20, io mem 0x1e1c0000
[ 6.676639] hub 1-0:1.0: USB hub found
[ 6.680467] hub 1-0:1.0: 2 ports detected
[ 6.685052] xhci-mtk 1e1c0000.xhci: xHCI Host Controller
[ 6.690366] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 2
[ 6.697886] xhci-mtk 1e1c0000.xhci: Host supports USB 3.0 SuperSpeed
[ 6.704507] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 6.713446] hub 2-0:1.0: USB hub found
[ 6.717275] hub 2-0:1.0: 1 port detected
[ 6.727313] usbcore: registered new interface driver usb-storage
[ 6.733578] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 6.750877] init: - preinit -
[ 7.180814] usb 2-1: new SuperSpeed USB device number 2 using xhci-mtk
[ 7.212805] random: procd: uninitialized urandom read (4 bytes read)
[ 7.212971] usb-storage 2-1:1.0: USB Mass Storage device detected
[ 7.225920] scsi host0: usb-storage 2-1:1.0
[ 7.366240] mtk_soc_eth 1e100000.ethernet: PPE started
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 10.582466] UBIFS (ubi0:1): default file-system created
[ 10.589130] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 496
[ 10.700430] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[ 10.708276] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 10.718161] UBIFS (ubi0:1): FS size: 31490048 bytes (30 MiB, 248 LEBs), journal size 1523712 bytes (1 MiB, 12 LEBs)
[ 10.728565] UBIFS (ubi0:1): reserved for root: 1487352 bytes (1452 KiB)
[ 10.735166] UBIFS (ubi0:1): media format: w4/r0 (latest is w5/r0), UUID , small LPT model
[ 10.749347] mount_root: overlay filesystem has not been fully initialized yet
[ 10.756981] mount_root: switching to ubifs overlay
[ 10.781065] urandom-seed: Seed file not found (/etc/urandom.seed)
[ 10.861172] mtk_soc_eth 1e100000.ethernet: 0x100 = 0x6060000c, 0x10c = 0x80818
[ 10.876085] procd: - early -
[ 10.879061] procd: - watchdog -
[ 11.550737] procd: - watchdog -
[ 11.554202] procd: - ubus -
[ 11.583502] random: ubusd: uninitialized urandom read (4 bytes read)
[ 11.611421] random: ubusd: uninitialized urandom read (4 bytes read)
[ 11.618117] random: ubusd: uninitialized urandom read (4 bytes read)
[ 11.625387] procd: - init -
Please press Enter to activate this console.
[ 12.046531] kmodloader: loading kernel modules from /etc/modules.d/*
[ 12.057746] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 12.069204] Loading modules backported from Linux version v5.3-rc4-0-gd45331b00ddb
[ 12.076775] Backport generated by backports.git v5.3-rc4-1-0-g4ec72687
[ 12.085114] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 12.096731] nf_conntrack version 0.5.0 (4096 buckets, 16384 max)
[ 12.127574] urngd: v1.0.0 started.
[ 12.145053] xt_time: kernel timezone is -0000
[ 12.214244] bus=0x1, slot = 0x0, irq=0x0
[ 12.218201] PCI: Enabling device 0000:00:00.0 (0004 -> 0006)
[ 12.241178] mt7615e 0000:01:00.0: HW/SW Version: 0x8a108a10, Build Time: 20180518100604a
[ 12.241178]
[ 12.266469] random: crng init done
[ 12.269877] random: 6 urandom warning(s) missed due to ratelimiting
[ 12.456236] mt7615e 0000:01:00.0: N9 Firmware Version: _reserved_, Build Time: 20190103180756
[ 12.471995] mt7615e 0000:01:00.0: CR4 Firmware Version: _reserved_, Build Time: 20181207140436
+ýýrýýýýýýýbus=0x2, slot = 0x1, irq=0x0
[ 20.131310] PCI: Enabling device 0000:00:01.0 (0004 -> 0006)
[ 20.161193] mt7615e 0000:02:00.0: HW/SW Version: 0x8a108a10, Build Time: 20180518100604a
[ 20.161193]
[ 20.185604] mt7615e 0000:02:00.0: N9 Firmware Version: _reserved_, Build Time: 20190103180756
[ 20.200746] mt7615e 0000:02:00.0: CR4 Firmware Version: _reserved_, Build Time: 20181207140436
[ 27.852570] PPP generic driver version 2.4.2
[ 27.858358] NET: Registered protocol family 24
[ 27.866716] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 41.276638] mtk_soc_eth 1e100000.ethernet: PPE started
[ 41.287935] br-lan: port 1(eth0.2) entered blocking state
[ 41.293420] br-lan: port 1(eth0.2) entered disabled state
[ 41.299522] device eth0.2 entered promiscuous mode
[ 41.304484] device eth0 entered promiscuous mode
[ 41.311947] br-lan: port 1(eth0.2) entered blocking state
[ 41.317384] br-lan: port 1(eth0.2) entered forwarding state
[ 41.323511] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 42.321086] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
BusyBox v1.31.0 () built-in shell (ash)
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
OpenWrt SNAPSHOT, r10942-9bebafcb5d
-----------------------------------------------------
=== WARNING! =====================================
There is no root password defined on this device!
Use the "passwd" command to set up a new password
in order to prevent unauthorized SSH logins.
--------------------------------------------------
root@OpenWrt:/# ifconfig -a
br-lan Link encap:Ethernet HWaddr
inet addr:192.168.1.1 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fde0:62db:5134::1/60 Scope:Global
inet6 addr: fe80::/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:41 errors:0 dropped:0 overruns:0 frame:0
TX packets:13 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:8012 (7.8 KiB) TX bytes:2126 (2.0 KiB)
eth0 Link encap:Ethernet HWaddr
inet6 addr: fe80::/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:102 errors:0 dropped:0 overruns:0 frame:0
TX packets:47 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:19418 (18.9 KiB) TX bytes:8199 (8.0 KiB)
Interrupt:21
eth0.1 Link encap:Ethernet HWaddr
inet6 addr: fe80::/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:20 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:3368 (3.2 KiB)
eth0.2 Link encap:Ethernet HWaddr
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:41 errors:0 dropped:0 overruns:0 frame:0
TX packets:13 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:8012 (7.8 KiB) TX bytes:2126 (2.0 KiB)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:28 errors:0 dropped:0 overruns:0 frame:0
TX packets:28 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:1904 (1.8 KiB) TX bytes:1904 (1.8 KiB)
wlan0 Link encap:Ethernet HWaddr
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
wlan1 Link encap:Ethernet HWaddr
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
root@OpenWrt:/# ls -l
drwxr-xr-x 2 root root 778 Sep 1 06:04 bin
drwxr-xr-x 4 root root 1300 Sep 1 06:05 dev
drwxr-xr-x 1 root root 512 Sep 1 06:05 etc
-rwxr-xr-x 1 root root 78 Dec 30 2018 init
drwxr-xr-x 11 root root 426 Sep 1 06:04 lib
drwxr-xr-x 2 root root 3 Sep 1 06:04 mnt
drwxr-xr-x 4 root root 360 Sep 1 06:05 overlay
dr-xr-xr-x 73 root root 0 Jan 1 1970 proc
drwxr-xr-x 16 root root 223 Sep 1 06:04 rom
drwxr-xr-x 2 root root 3 Sep 1 06:04 root
drwxr-xr-x 2 root root 822 Sep 1 06:04 sbin
dr-xr-xr-x 11 root root 0 Jan 1 1970 sys
drwxrwxrwt 15 root root 380 Sep 1 06:05 tmp
drwxr-xr-x 7 root root 89 Sep 1 06:04 usr
lrwxrwxrwx 1 root root 3 Sep 1 06:04 var -> tmp
drwxr-xr-x 2 root root 3 Sep 1 06:04 www
root@OpenWrt:/# ps
PID USER VSZ STAT COMMAND
1 root 1576 S /sbin/procd
2 root 0 SW [kthreadd]
3 root 0 IW [kworker/0:0]
4 root 0 IW< [kworker/0:0H]
5 root 0 IW [kworker/u8:0]
6 root 0 IW< [mm_percpu_wq]
7 root 0 SW [ksoftirqd/0]
8 root 0 IW [rcu_sched]
9 root 0 IW [rcu_bh]
10 root 0 SW [migration/0]
11 root 0 SW [cpuhp/0]
12 root 0 SW [cpuhp/1]
13 root 0 SW [migration/1]
14 root 0 SW [ksoftirqd/1]
16 root 0 IW< [kworker/1:0H]
17 root 0 SW [cpuhp/2]
18 root 0 SW [migration/2]
19 root 0 SW [ksoftirqd/2]
21 root 0 IW< [kworker/2:0H]
22 root 0 SW [cpuhp/3]
23 root 0 SW [migration/3]
24 root 0 SW [ksoftirqd/3]
25 root 0 IW [kworker/3:0]
26 root 0 IW< [kworker/3:0H]
27 root 0 IW< [netns]
41 root 0 IW [kworker/u8:3]
68 root 0 IW [kworker/3:1]
69 root 0 IW [kworker/2:1]
138 root 0 IW [kworker/1:1]
139 root 0 SW [oom_reaper]
140 root 0 IW< [writeback]
142 root 0 SW [kcompactd0]
143 root 0 IW< [crypto]
145 root 0 IW< [kblockd]
175 root 0 IW< [watchdogd]
199 root 0 SW [kswapd0]
268 root 0 IW< [pencrypt]
270 root 0 IW< [pdecrypt]
366 root 0 IW< [ipv6_addrconf]
378 root 0 SW [ubi_bgt0d]
383 root 0 IW< [kworker/0:1H]
384 root 0 IW< [kworker/2:1H]
385 root 0 IW [kworker/2:2]
386 root 0 IW< [kworker/3:1H]
389 root 0 IW< [kworker/1:1H]
429 root 0 IW [kworker/0:2]
437 root 0 IW [kworker/1:2]
453 root 0 SW [scsi_eh_0]
454 root 0 IW< [scsi_tmf_0]
455 root 0 SW [usb-storage]
496 root 0 SW [ubifs_bgt0_1]
573 root 1220 S /sbin/ubusd
574 root 1220 S /bin/ash --login
591 root 1028 S /sbin/urngd
660 root 0 IW< [cfg80211]
1012 root 1248 S /sbin/logd -S 64
1074 dnsmasq 1344 S /usr/sbin/dnsmasq -C /var/etc/dnsmasq.conf.cfg01411c
1111 root 1080 S /usr/sbin/dropbear -F -P /var/run/dropbear.1.pid -p
1168 root 1700 S /sbin/netifd
1204 root 1448 S /usr/sbin/odhcpd
1360 root 1212 S udhcpc -p /var/run/udhcpc-eth0.1.pid -s /lib/netifd/
1361 root 1052 S odhcp6c -s /lib/netifd/dhcpv6.script -P0 -t120 eth0.
1391 root 1212 S< /usr/sbin/ntpd -n -N -S /usr/sbin/ntpd-hotplug -p 0.
1720 root 1212 R ps
root@OpenWrt:/etc# ping www.google.co
PING www.google.co (): 56 data bytes
64 bytes from : seq=0 ttl=52 time=4.718 ms
^C
--- www.google.co ping statistics ---
1 packets transmitted, 1 packets received, 0% packet loss
round-trip min/avg/max = 4.718/4.718/4.718 ms
root@OpenWrt:/etc# ping www.google.com
PING www.google.com (): 56 data bytes
64 bytes from : seq=0 ttl=47 time=4.927 ms
64 bytes from : seq=1 ttl=47 time=4.687 ms
^C
--- www.google.com ping statistics ---
2 packets transmitted, 2 packets received, 0% packet loss
round-trip min/avg/max = 4.687/4.807/4.927 ms
root@OpenWrt:/etc# opkg update
Downloading http://downloads.openwrt.org/snapshots/targets/ramips/mt7621/packages/Packages.gz
Updated list of available packages in /var/opkg-lists/openwrt_core
Downloading http://downloads.openwrt.org/snapshots/targets/ramips/mt7621/packages/Packages.sig
Signature check passed.
Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/base/Packages.gz
Updated list of available packages in /var/opkg-lists/openwrt_base
Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/base/Packages.sig
Signature check passed.
Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/Packages.gz
Updated list of available packages in /var/opkg-lists/openwrt_luci
Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/Packages.sig
Signature check passed.
Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/packages/Packages.gz
Updated list of available packages in /var/opkg-lists/openwrt_packages
Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/packages/Packages.sig
Signature check passed.
Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/routing/Packages.gz
Updated list of available packages in /var/opkg-lists/openwrt_routing
Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/routing/Packages.sig
Signature check passed.
Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/telephony/Packages.gz
Updated list of available packages in /var/opkg-lists/openwrt_telephony
Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/telephony/Packages.sig
Signature check passed.
root@OpenWrt:/etc# opkg install luci
Installing luci (git-19.241.65047-dffe9ca-1) to root...
Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/luci_git-19.241.65047-dffe9ca-1_all.ipk
Installing uhttpd (2019-08-17-6b03f960-3) to root...
Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/base/uhttpd_2019-08-17-6b03f960-3_mipsel_24kc.ipk
Installing liblua5.1.5 (5.1.5-5) to root...
Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/base/liblua5.1.5_5.1.5-5_mipsel_24kc.ipk
Installing lua (5.1.5-5) to root...
Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/base/lua_5.1.5-5_mipsel_24kc.ipk
Installing luci-lib-nixio (git-19.241.65047-dffe9ca-1) to root...
Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/luci-lib-nixio_git-19.241.65047-dffe9ca-1_mipsel_24kc.ipk
Installing luci-lib-ip (git-19.241.65047-dffe9ca-1) to root...
Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/luci-lib-ip_git-19.241.65047-dffe9ca-1_mipsel_24kc.ipk
Installing rpcd (2019-06-05-89bfaa42-3) to root...
Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/base/rpcd_2019-06-05-89bfaa42-3_mipsel_24kc.ipk
Installing libubus-lua (2018-10-06-221ce7e7-1) to root...
Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/base/libubus-lua_2018-10-06-221ce7e7-1_mipsel_24kc.ipk
Installing luci-lib-jsonc (git-19.241.65047-dffe9ca-1) to root...
Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/luci-lib-jsonc_git-19.241.65047-dffe9ca-1_mipsel_24kc.ipk
Installing liblucihttp0 (2019-07-05-a34a17d5-1) to root...
Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/liblucihttp0_2019-07-05-a34a17d5-1_mipsel_24kc.ipk
Installing liblucihttp-lua (2019-07-05-a34a17d5-1) to root...
Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/liblucihttp-lua_2019-07-05-a34a17d5-1_mipsel_24kc.ipk
Installing luci-base (git-19.241.65047-dffe9ca-1) to root...
Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/luci-base_git-19.241.65047-dffe9ca-1_mipsel_24kc.ipk
Installing libiwinfo-lua (2019-08-28-a9f95570-1) to root...
Downloading http://downloads.openwrt.org/snapshots/targets/ramips/mt7621/packages/libiwinfo-lua_2019-08-28-a9f95570-1_mipsel_24kc.ipk
Installing luci-mod-status (git-19.241.65047-dffe9ca-1) to root...
Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/luci-mod-status_git-19.241.65047-dffe9ca-1_mipsel_24kc.ipk
Installing luci-mod-system (git-19.241.65047-dffe9ca-1) to root...
Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/luci-mod-system_git-19.241.65047-dffe9ca-1_all.ipk
Installing luci-mod-network (git-19.241.65047-dffe9ca-1) to root...
Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/luci-mod-network_git-19.241.65047-dffe9ca-1_all.ipk
Installing luci-mod-admin-full (git-19.241.65047-dffe9ca-1) to root...
Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/luci-mod-admin-full_git-19.241.65047-dffe9ca-1_all.ipk
Installing luci-theme-bootstrap (git-19.241.65047-dffe9ca-1) to root...
Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/luci-theme-bootstrap_git-19.241.65047-dffe9ca-1_all.ipk
Installing luci-app-firewall (git-19.241.65047-dffe9ca-1) to root...
Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/luci-app-firewall_git-19.241.65047-dffe9ca-1_all.ipk
Installing luci-app-opkg (git-19.241.65047-dffe9ca-1) to root...
Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/luci-app-opkg_git-19.241.65047-dffe9ca-1_all.ipk
Installing luci-proto-ppp (git-19.241.65047-dffe9ca-1) to root...
Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/luci-proto-ppp_git-19.241.65047-dffe9ca-1_all.ipk
Installing luci-proto-ipv6 (git-19.241.65047-dffe9ca-1) to root...
Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/luci-proto-ipv6_git-19.241.65047-dffe9ca-1_all.ipk
Installing rpcd-mod-rrdns (20170710) to root...
Downloading http://downloads.openwrt.org/snapshots/packages/mipsel_24kc/luci/rpcd-mod-rrdns_20170710_mipsel_24kc.ipk
Configuring liblucihttp0.
Configuring luci-app-opkg.
Configuring rpcd.
Configuring liblua5.1.5.
Configuring luci-lib-ip.
Configuring libubus-lua.
Configuring libiwinfo-lua.
Configuring lua.
Configuring luci-lib-nixio.
Configuring luci-lib-jsonc.
Configuring liblucihttp-lua.
Configuring luci-base.
Configuring luci-mod-system.
Configuring luci-theme-bootstrap.
Configuring luci-mod-status.
Configuring luci-app-firewall.
Configuring luci-proto-ppp.
Configuring luci-mod-network.
Configuring luci-mod-admin-full.
Configuring luci-proto-ipv6.
Configuring uhttpd.
Configuring rpcd-mod-rrdns.
Configuring luci.
root@OpenWrt:/etc# df -h
Filesystem Size Used Available Use% Mounted on
/dev/root 2.8M 2.8M 0 100% /rom
tmpfs 123.5M 764.0K 122.8M 1% /tmp
/dev/ubi0_1 27.1M 1.4M 24.3M 5% /overlay
overlayfs:/overlay 27.1M 1.4M 24.3M 5% /
tmpfs 512.0K 0 512.0K 0% /dev
root@OpenWrt:/etc# [ 2075.963720] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 2075.973245] br-lan: port 2(wlan0) entered blocking state
[ 2075.978551] br-lan: port 2(wlan0) entered disabled state
[ 2075.984368] device wlan0 entered promiscuous mode
[ 2087.165173] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 2087.171890] br-lan: port 2(wlan0) entered blocking state
[ 2087.177194] br-lan: port 2(wlan0) entered forwarding state
[ 2096.494533] device wlan0 left promiscuous mode
[ 2096.499322] br-lan: port 2(wlan0) entered disabled state
[ 2097.382887] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 2097.393568] br-lan: port 2(wlan0) entered blocking state
[ 2097.398924] br-lan: port 2(wlan0) entered disabled state
[ 2097.404922] device wlan0 entered promiscuous mode
[ 2097.409972] br-lan: port 2(wlan0) entered blocking state
[ 2097.415296] br-lan: port 2(wlan0) entered forwarding state
[ 2097.749351] br-lan: port 2(wlan0) entered disabled state
[ 2107.953875] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 2107.960561] br-lan: port 2(wlan0) entered blocking state
[ 2107.965861] br-lan: port 2(wlan0) entered forwarding state
[ 2117.964353] device wlan0 left promiscuous mode
[ 2117.969130] br-lan: port 2(wlan0) entered disabled state
[ 2118.782586] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 2118.792816] br-lan: port 2(wlan0) entered blocking state
[ 2118.798173] br-lan: port 2(wlan0) entered disabled state
[ 2118.804171] device wlan0 entered promiscuous mode
[ 2118.809362] br-lan: port 2(wlan0) entered blocking state
[ 2118.814692] br-lan: port 2(wlan0) entered forwarding state
[ 2119.189273] br-lan: port 2(wlan0) entered disabled state
[ 2130.258107] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 2130.264811] br-lan: port 2(wlan0) entered blocking state
[ 2130.270163] br-lan: port 2(wlan0) entered forwarding state
[ 2245.748473] device wlan0 left promiscuous mode
[ 2245.753145] br-lan: port 2(wlan0) entered disabled state
[ 2246.536062] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 2246.546273] br-lan: port 2(wlan0) entered blocking state
[ 2246.551680] br-lan: port 2(wlan0) entered disabled state
[ 2246.557667] device wlan0 entered promiscuous mode
[ 2246.562855] br-lan: port 2(wlan0) entered blocking state
[ 2246.568267] br-lan: port 2(wlan0) entered forwarding state
[ 2246.838430] br-lan: port 2(wlan0) entered disabled state
[ 2246.948147] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[ 2246.954850] br-lan: port 2(wlan1) entered blocking state
[ 2246.960197] br-lan: port 2(wlan1) entered forwarding state
root@OpenWrt:/etc#
root@OpenWrt:/etc# uci show wireless
wireless.radio0=wifi-device
wireless.radio0.type='mac80211'
wireless.radio0.channel='11'
wireless.radio0.hwmode='11g'
wireless.radio0.path='pci0000:00/0000:00:00.0/0000:01:00.0'
wireless.radio0.country='00'
wireless.radio0.legacy_rates='1'
wireless.radio0.htmode='HT20'
wireless.default_radio0=wifi-iface
wireless.default_radio0.device='radio0'
wireless.default_radio0.network='lan'
wireless.default_radio0.mode='ap'
wireless.default_radio0.encryption='psk2'
wireless.default_radio0.key='qwerty1234'
wireless.default_radio0.ssid='asdf'
wireless.radio1=wifi-device
wireless.radio1.type='mac80211'
wireless.radio1.channel='36'
wireless.radio1.hwmode='11a'
wireless.radio1.path='pci0000:00/0000:00:01.0/0000:02:00.0'
wireless.radio1.htmode='VHT80'
wireless.radio1.__toggle='Enable'
wireless.radio1.country='00'
wireless.radio1.legacy_rates='1'
wireless.default_radio1=wifi-iface
wireless.default_radio1.device='radio1'
wireless.default_radio1.network='lan'
wireless.default_radio1.mode='ap'
wireless.default_radio1.ssid='asdf'
wireless.default_radio1.encryption='psk2'
wireless.default_radio1.key='qwerty1234'
root@OpenWrt:/etc#
Firmware:
./staging_dir/target-mipsel_24kc_glibc/root-ramips/lib/firmware/mediatek/mt7615_rom_patch.bin