Last modified by Leon Poon on 2021/07/16 18:40
From version 31.1
edited by Leon Poon
on 2020/09/10 14:22
Change comment: There is no comment for this version
To version 12.1
edited by Leon Poon
on 2019/11/02 14:42
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -1,41 +1,8 @@
1 1  switch0: port 0 = wan, port 1,2,3,4 = lan
2 2  
3 -If you brick your router you should be able to recover by soldering the UART pin headers and connecting to the serial. See [[this page for pictures>>doc:Linksys EA8100.WebHome]].
4 4  
4 +[[https:~~/~~/github.com/LeonPoon/openwrt/compare/master...master-linksys_ea8100>>https://github.com/LeonPoon/openwrt/compare/master...master-linksys_ea8100]]
5 5  
6 -= 19.07.x =
7 -
8 -19.07.4 is here!
9 -
10 -[[https:~~/~~/www.codepowered.com/openwrt/v19.07.4/linksys_ea8100/>>https://www.codepowered.com/openwrt/v19.07.4/linksys_ea8100/]] ([[https:~~/~~/github.com/LeonPoon/openwrt/compare/v19.07.4...v19.07.4-linksys_ea8100>>https://github.com/LeonPoon/openwrt/compare/v19.07.4...v19.07.4-linksys_ea8100]])
11 -
12 -The EA8100 contains 2 firmware partitions. Using the Linksys UI will flash openwrt into only one of the 2 partitions. The booting process switches partition every few boots, so if you want to always boot into openwrt then you have to flash openwrt into both partitions.
13 -
14 -**Images do not contain LuCi! (The build process doesn't include it for some reason I have not yet time to figure out.)** You need to have the squashfs.bin flashed, then opkg update and opkg install luci.
15 -
16 -How to flash if your router currently has stock Linksys firmware:
17 -
18 -1. Flash the "**initramfs-factory.img**" via Linksys UI. Wait for it to start to reboot.
19 -1. Configure your computer to have ip in 192.168.1.0/24 subnet but NOT 192.168.1.1. (so, use 192.168.1.2.) Start ping to 192.168.1.1.
20 -1. Cross your fingers that the router boots openwrt. Otherwise keep rebooting until it loads the openwrt partition. (Usually 3 times max.) Wait a few minutes from reboot to let it load. If you get ping response from 192.168.1.1 it means openwrt loaded.
21 -1. Scp the "**squashfs-sysupgrade.bin**" into /tmp in the router. root@192.168.1.1. No password.
22 -1. Log in as root via SSH into shell. No password.
23 -1. **Sysupgrade the uploaded squashfs-sysupgrade.bin**. This should flash the openwrt firmware into both firmware partitions. It auto reboots.
24 -1. opkg update
25 -1. **opkg install luci (the flashed images does not contain Luci)**
26 -1. Access LuCI via http:~/~/192.168.1.1/. You can now configure.
27 -
28 -If you are on my 18.x below, sysupgrading to a 19.07 image will not work. You have to manually mtd write the 19.07 "kernel-initramfs.bin" into the nand and boot/log into it (192.168.1.1), then sysupgrade.
29 -
30 -Sysupgrade from 19.07.x to another 19.07.y will work. **HOWEVER: **sysupgrade will wipe entire firmware partitions! Backup your files/config before sysupgrade.
31 -
32 -Since [[19.07.03>>https://www.codepowered.com/openwrt/v19.07.3/linksys_ea8100/]], as of 19.07.04:
33 -
34 -* Wifi (5Ghz) seem to work at 30-40MB/s with a MacBook Pro.
35 -* **Known issue**: 2.4Ghz wifi performance is really bad. You probably want to disable 2.4Ghz wifi.
36 -
37 -= 18.x =
38 -
39 39  9bebafcb5dfe37f25285fa18fb8bfe7b68011267 (with wifi support) Download:
40 40  
41 41  * [[initramfs-kernel.bin>>attach:openwrt-ramips-mt7621-linksys_ea8100-initramfs-kernel-9bebafcb5dfe37f25285fa18fb8bfe7b68011267.bin]]